From: Yongqiang Niu <yongqiang.niu@mediatek.com>
To: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: CK Hu <ck.hu@mediatek.com>,
Philipp Zabel <p.zabel@pengutronix.de>,
Matthias Brugger <matthias.bgg@gmail.com>,
David Airlie <airlied@linux.ie>, Daniel Vetter <daniel@ffwll.ch>,
Mark Rutland <mark.rutland@arm.com>,
dri-devel <dri-devel@lists.freedesktop.org>,
Devicetree List <devicetree@vger.kernel.org>,
lkml <linux-kernel@vger.kernel.org>,
"moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE"
<linux-arm-kernel@lists.infradead.org>,
"moderated list:ARM/Mediatek SoC support"
<linux-mediatek@lists.infradead.org>
Subject: Re: [PATCH v11 7/9] drm/mediatek: enable dither function
Date: Thu, 28 Jan 2021 16:28:42 +0800 [thread overview]
Message-ID: <1611822522.1947.12.camel@mhfsdcap03> (raw)
In-Reply-To: <CAJMQK-h1_d1+SpxMC8LGPJK=X9HHoJ_ueFzV2Sq44buCiaXFUA@mail.gmail.com>
On Thu, 2021-01-28 at 16:18 +0800, Hsin-Yi Wang wrote:
> On Thu, Jan 28, 2021 at 4:10 PM Yongqiang Niu
> <yongqiang.niu@mediatek.com> wrote:
> >
> > On Thu, 2021-01-28 at 16:07 +0800, CK Hu wrote:
> > > On Thu, 2021-01-28 at 15:59 +0800, Yongqiang Niu wrote:
> > > > On Thu, 2021-01-28 at 15:42 +0800, CK Hu wrote:
> > > > > Hi, Hsin-Yi:
> > > > >
> > > > > On Thu, 2021-01-28 at 15:28 +0800, Hsin-Yi Wang wrote:
> > > > > > From: Yongqiang Niu <yongqiang.niu@mediatek.com>
> > > > > >
> > > > > > for 5 or 6 bpc panel, we need enable dither function
> > > > > > to improve the display quality
> > > > > >
> > > > > > Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
> > > > > > Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
> > > > > > ---
> > > > > > drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.c | 44 ++++++++++++++++++++-
> > > > > > 1 file changed, 43 insertions(+), 1 deletion(-)
> > > > > >
> > > > > > diff --git a/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.c b/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.c
> > > > > > index 8173f709272be..e85625704d611 100644
> > > > > > --- a/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.c
> > > > > > +++ b/drivers/gpu/drm/mediatek/mtk_drm_ddp_comp.c
> > > > > > @@ -53,7 +53,9 @@
> > > > > > #define DITHER_EN BIT(0)
> > > > > > #define DISP_DITHER_CFG 0x0020
> > > > > > #define DITHER_RELAY_MODE BIT(0)
> > > > > > +#define DITHER_ENGINE_EN BIT(1)
> > > > > > #define DISP_DITHER_SIZE 0x0030
> > > > > > +#define DITHER_REG(idx) (0x100 + (idx) * 4)
> > > > > >
> > > > > > #define LUT_10BIT_MASK 0x03ff
> > > > > >
> > > > > > @@ -313,8 +315,48 @@ static void mtk_dither_config(struct device *dev, unsigned int w,
> > > > > > {
> > > > > > struct mtk_ddp_comp_dev *priv = dev_get_drvdata(dev);
> > > > > >
> > > > > > + bool enable = false;
> > > > > > +
> > > > > > + /* default value for dither reg 5 to 14 */
> > > > > > + const u32 dither_setting[] = {
> > > > > > + 0x00000000, /* 5 */
> > > > > > + 0x00003002, /* 6 */
> > > > > > + 0x00000000, /* 7 */
> > > > > > + 0x00000000, /* 8 */
> > > > > > + 0x00000000, /* 9 */
> > > > > > + 0x00000000, /* 10 */
> > > > > > + 0x00000000, /* 11 */
> > > > > > + 0x00000011, /* 12 */
> > > > > > + 0x00000000, /* 13 */
> > > > > > + 0x00000000, /* 14 */
> > > > >
> > > > > Could you explain what is this?
> > > >
> > > > this is dither 5 to dither 14 setting
> > > > this will be useless, we just need set dither 5 and dither 7 like
> > > > mtk_ddp_write(cmdq_pkt, 0, comp, DISP_DITHER_5);
> > > > mtk_ddp_write(cmdq_pkt, 0, comp, DISP_DITHER_7);
> > > > other value is same with hardware default value.
> > > >
> > > >
> > > > >
> > > > > > + };
> > > > > > +
> > > > > > + if (bpc == 5 || bpc == 6) {
> > > > > > + enable = true;
> > > > > > + mtk_ddp_write(cmdq_pkt,
> > > > > > + DITHER_LSB_ERR_SHIFT_R(MTK_MAX_BPC - bpc) |
> > > > > > + DITHER_ADD_LSHIFT_R(MTK_MAX_BPC - bpc) |
> > > > > > + DITHER_NEW_BIT_MODE,
> > > > > > + &priv->cmdq_reg, priv->regs, DITHER_REG(15));
> > > > > > + mtk_ddp_write(cmdq_pkt,
> > > > > > + DITHER_LSB_ERR_SHIFT_B(MTK_MAX_BPC - bpc) |
> > > > > > + DITHER_ADD_LSHIFT_B(MTK_MAX_BPC - bpc) |
> > > > > > + DITHER_LSB_ERR_SHIFT_G(MTK_MAX_BPC - bpc) |
> > > > > > + DITHER_ADD_LSHIFT_G(MTK_MAX_BPC - bpc),
> > > > >
> > > > > This result in 0x50505050, but previous version is 0x50504040, so this
> > > > > version is correct and previous version is incorrect?
> > > >
> > > > the new version set r g b 3 channel same, seams more reasonable
> > > >
> > > >
> > >
> > > So all the setting of DISP_DITHER_5, DISP_DITHER_7, DISP_DITHER_15,
> > > DISP_DITHER_16 is identical to mtk_dither_set(), so call
> > > mtk_dither_set() instead of duplication here.
> > >
> >
> > dither enable set in mtk_dither_set is
> > mtk_ddp_write(cmdq_pkt, DISP_DITHERING, comp, CFG);
> >
> > that is different 8183 and mt8192.
> > mt8173 dither enable in gamma is bit2
> > mt8183 and mt8192 dither engine enable is bit 1
> >
> >
>
> We can still call mtk_dither_set() for bpc is 5 or 6 here, though it
> will be set to bit2,
> but later in mtk_ddp_write(cmdq_pkt, enable ? DITHER_ENGINE_EN :
> DITHER_RELAY_MODE, &priv->cmdq_reg, priv->regs, DISP_DITHER_CFG); it
> will be correct back to bit 1.
>
> Is this reasonable?
the result is ok.
>
> > > Regards,
> > > CK
> > > > >
> > > > > Regards,
> > > > > CK
> > > > >
> > > > > > + &priv->cmdq_reg, priv->regs, DITHER_REG(16));
> > > > > > + }
> > > > > > +
> > > > > > +
> > > > > > + if (enable) {
> > > > > > + u32 idx;
> > > > > > +
> > > > > > + for (idx = 0; idx < ARRAY_SIZE(dither_setting); idx++)
> > > > > > + mtk_ddp_write(cmdq_pkt, dither_setting[idx], &priv->cmdq_reg, priv->regs,
> > > > > > + DITHER_REG(idx + 5));
> > > > > > + }
> > > > > > +
> > > > > > mtk_ddp_write(cmdq_pkt, h << 16 | w, &priv->cmdq_reg, priv->regs, DISP_DITHER_SIZE);
> > > > > > - mtk_ddp_write(cmdq_pkt, DITHER_RELAY_MODE, &priv->cmdq_reg, priv->regs, DISP_DITHER_CFG);
> > > > > > + mtk_ddp_write(cmdq_pkt, enable ? DITHER_ENGINE_EN : DITHER_RELAY_MODE, &priv->cmdq_reg, priv->regs, DISP_DITHER_CFG);
> > > > > > }
> > > > > >
> > > > > > static void mtk_dither_start(struct device *dev)
> > > > >
> > > > >
> > > >
> > > >
> > >
> > >
> >
next prev parent reply other threads:[~2021-01-28 8:30 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-01-28 7:27 [PATCH v11 0/9] drm/mediatek: add support for mediatek SOC MT8183 Hsin-Yi Wang
2021-01-28 7:27 ` [PATCH v11 1/9] arm64: dts: mt8183: rename rdma fifo size Hsin-Yi Wang
2021-01-28 10:24 ` Enric Balletbo Serra
2021-01-28 7:27 ` [PATCH v11 2/9] arm64: dts: mt8183: refine gamma compatible name Hsin-Yi Wang
2021-01-28 9:11 ` Enric Balletbo Serra
2021-01-28 7:27 ` [PATCH v11 3/9] drm/mediatek: add RDMA fifo size error handle Hsin-Yi Wang
2021-01-28 7:50 ` CK Hu
2021-01-28 11:12 ` Hsin-Yi Wang
2021-01-28 7:27 ` [PATCH v11 4/9] drm/mediatek: add mtk_dither_set_common() function Hsin-Yi Wang
2021-01-28 7:39 ` CK Hu
2021-01-28 7:27 ` [PATCH v11 5/9] drm/mediatek: separate gamma module Hsin-Yi Wang
2021-01-28 7:27 ` [PATCH v11 6/9] drm/mediatek: add has_dither private data for gamma Hsin-Yi Wang
2021-01-28 7:28 ` [PATCH v11 7/9] drm/mediatek: enable dither function Hsin-Yi Wang
2021-01-28 7:42 ` CK Hu
2021-01-28 7:59 ` Yongqiang Niu
2021-01-28 8:07 ` CK Hu
2021-01-28 8:09 ` Yongqiang Niu
2021-01-28 8:18 ` Hsin-Yi Wang
2021-01-28 8:28 ` Yongqiang Niu [this message]
2021-01-28 8:28 ` CK Hu
2021-01-28 8:32 ` Yongqiang Niu
2021-01-28 8:41 ` Hsin-Yi Wang
2021-01-28 7:28 ` [PATCH v11 8/9] soc: mediatek: add mtk mutex support for MT8183 Hsin-Yi Wang
2021-01-28 7:46 ` CK Hu
2021-01-28 7:28 ` [PATCH v11 9/9] drm/mediatek: add support for mediatek SOC MT8183 Hsin-Yi Wang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1611822522.1947.12.camel@mhfsdcap03 \
--to=yongqiang.niu@mediatek.com \
--cc=airlied@linux.ie \
--cc=ck.hu@mediatek.com \
--cc=daniel@ffwll.ch \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=hsinyi@chromium.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=mark.rutland@arm.com \
--cc=matthias.bgg@gmail.com \
--cc=p.zabel@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).