From: Jernej Skrabec <jernej.skrabec@siol.net>
To: maxime.ripard@free-electrons.com, wens@csie.org,
airlied@linux.ie, robh+dt@kernel.org, mark.rutland@arm.com,
mturquette@baylibre.com, sboyd@kernel.org
Cc: jernej.skrabec@siol.net, dri-devel@lists.freedesktop.org,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org,
linux-sunxi@googlegroups.com
Subject: [PATCH 13/15] ARM: dts: sunxi: h3/h5: Add HDMI pipeline
Date: Sat, 24 Feb 2018 22:45:43 +0100 [thread overview]
Message-ID: <20180224214545.3740-14-jernej.skrabec@siol.net> (raw)
In-Reply-To: <20180224214545.3740-1-jernej.skrabec@siol.net>
This commit adds all entries needed for HDMI to function properly.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
---
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 108 +++++++++++++++++++++++++++++++++++++
1 file changed, 108 insertions(+)
diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
index 7a83b15225c7..e70348ed9bc0 100644
--- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -105,6 +105,12 @@
};
};
+ de: display-engine {
+ compatible = "allwinner,sun8i-h3-display-engine";
+ allwinner,pipelines = <&mixer0>;
+ status = "disabled";
+ };
+
soc {
compatible = "simple-bus";
#address-cells = <1>;
@@ -123,6 +129,29 @@
#reset-cells = <1>;
};
+ mixer0: mixer@1100000 {
+ compatible = "allwinner,sun8i-h3-de2-mixer-0";
+ reg = <0x01100000 0x100000>;
+ clocks = <&display_clocks CLK_BUS_MIXER0>,
+ <&display_clocks CLK_MIXER0>;
+ clock-names = "bus",
+ "mod";
+ resets = <&display_clocks RST_MIXER0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mixer0_out: port@1 {
+ reg = <1>;
+
+ mixer0_out_tcon0: endpoint {
+ remote-endpoint = <&tcon0_in_mixer0>;
+ };
+ };
+ };
+ };
+
syscon: syscon@1c00000 {
compatible = "allwinner,sun8i-h3-system-controller",
"syscon";
@@ -138,6 +167,41 @@
#dma-cells = <1>;
};
+ tcon0: lcd-controller@1c0c000 {
+ compatible = "allwinner,sun8i-h3-tcon-tv",
+ "allwinner,sun8i-a83t-tcon-tv";
+ reg = <0x01c0c000 0x1000>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>;
+ clock-names = "ahb", "tcon-ch1";
+ resets = <&ccu RST_BUS_TCON0>;
+ reset-names = "lcd";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon0_in: port@0 {
+ reg = <0>;
+
+ tcon0_in_mixer0: endpoint {
+ remote-endpoint = <&mixer0_out_tcon0>;
+ };
+ };
+
+ tcon0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ tcon0_out_hdmi: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&hdmi_in_tcon0>;
+ };
+ };
+ };
+ };
+
mmc0: mmc@1c0f000 {
/* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c0f000 0x1000>;
@@ -684,6 +748,50 @@
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};
+ hdmi: hdmi@1ee0000 {
+ compatible = "allwinner,sun8i-h3-dw-hdmi",
+ "allwinner,sun8i-a83t-dw-hdmi";
+ reg = <0x01ee0000 0x10000>;
+ reg-io-width = <1>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
+ <&ccu CLK_HDMI>;
+ clock-names = "iahb", "isfr", "tmds";
+ resets = <&ccu RST_BUS_HDMI1>;
+ reset-names = "ctrl";
+ phys = <&hdmi_phy>;
+ phy-names = "hdmi-phy";
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hdmi_in: port@0 {
+ reg = <0>;
+
+ hdmi_in_tcon0: endpoint {
+ remote-endpoint = <&tcon0_out_hdmi>;
+ };
+ };
+
+ hdmi_out: port@1 {
+ reg = <1>;
+ };
+ };
+ };
+
+ hdmi_phy: hdmi-phy@1ef0000 {
+ compatible = "allwinner,sun8i-h3-hdmi-phy";
+ reg = <0x01ef0000 0x10000>;
+ clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
+ <&ccu 6>;
+ clock-names = "bus", "mod", "pll-0";
+ resets = <&ccu RST_BUS_HDMI0>;
+ reset-names = "phy";
+ #phy-cells = <0>;
+ };
+
rtc: rtc@1f00000 {
compatible = "allwinner,sun6i-a31-rtc";
reg = <0x01f00000 0x54>;
--
2.16.2
next prev parent reply other threads:[~2018-02-24 21:46 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-02-24 21:45 [PATCH 00/15] Implement H3/H5 HDMI driver Jernej Skrabec
2018-02-24 21:45 ` [PATCH 01/15] clk: sunxi-ng: Add check for minimal rate to NM PLLs Jernej Skrabec
2018-02-26 9:38 ` Maxime Ripard
2018-02-26 9:43 ` Chen-Yu Tsai
2018-02-26 10:25 ` Maxime Ripard
2018-02-26 10:28 ` Chen-Yu Tsai
2018-02-26 16:17 ` Jernej Škrabec
2018-02-24 21:45 ` [PATCH 02/15] clk: sunxi-ng: h3: h5: Add minimal rate for video PLL Jernej Skrabec
2018-02-24 21:45 ` [PATCH 03/15] clk: sunxi-ng: h3: h5: Allow some clocks to set parent rate Jernej Skrabec
2018-02-24 21:45 ` [PATCH 04/15] clk: sunxi-ng: h3: h5: export CLK_PLL_VIDEO Jernej Skrabec
2018-02-24 21:45 ` [PATCH 05/15] dt-bindings: display: sun4i-drm: Add compatibles for H3 HDMI pipeline Jernej Skrabec
2018-02-24 21:45 ` [PATCH 06/15] drm/sun4i: Add support for H3 display engine Jernej Skrabec
2018-02-24 21:45 ` [PATCH 07/15] drm/sun4i: Add support for H3 mixer 0 Jernej Skrabec
2018-02-24 21:45 ` [PATCH 08/15] drm/sun4i: Fix polarity configuration for DW HDMI PHY Jernej Skrabec
2018-02-26 9:39 ` Maxime Ripard
2018-02-26 16:19 ` Jernej Škrabec
2018-02-24 21:45 ` [PATCH 09/15] drm/sun4i: Add support for variants to " Jernej Skrabec
2018-02-24 21:45 ` [PATCH 10/15] drm/sun4i: Move and expand DW HDMI PHY register macros Jernej Skrabec
2018-02-24 21:45 ` [PATCH 11/15] drm/sun4i: Add support for H3 HDMI PHY variant Jernej Skrabec
2018-02-26 16:24 ` Jernej Škrabec
2018-02-24 21:45 ` [PATCH 12/15] drm/sun4i: Allow building on arm64 Jernej Skrabec
2018-02-27 2:18 ` kbuild test robot
2018-02-24 21:45 ` Jernej Skrabec [this message]
2018-02-24 21:45 ` [PATCH 14/15] ARM: dts: sun8i: h3: Enable HDMI output on H3 boards Jernej Skrabec
2018-02-25 8:11 ` [linux-sunxi] " Julian Calaby
2018-02-25 8:43 ` Icenowy Zheng
2018-02-25 9:06 ` Julian Calaby
2018-02-25 9:08 ` Icenowy Zheng
2018-02-26 16:16 ` Jernej Škrabec
2018-02-26 16:21 ` Icenowy Zheng
2018-02-26 16:27 ` Jernej Škrabec
2018-02-27 2:29 ` Julian Calaby
2018-02-27 7:07 ` Maxime Ripard
2018-02-27 10:35 ` Julian Calaby
2018-02-24 21:45 ` [PATCH 15/15] ARM64: dts: sun50i: h5: Enable HDMI output on H5 boards Jernej Skrabec
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180224214545.3740-14-jernej.skrabec@siol.net \
--to=jernej.skrabec@siol.net \
--cc=airlied@linux.ie \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sunxi@googlegroups.com \
--cc=mark.rutland@arm.com \
--cc=maxime.ripard@free-electrons.com \
--cc=mturquette@baylibre.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).