linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Nicolin Chen <nicoleotsuka@gmail.com>
To: jdelvare@suse.com, linux@roeck-us.net
Cc: linux-hwmon@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH v3 5/5] hwmon: (ina3221) Add PM runtime support
Date: Wed, 24 Oct 2018 12:34:02 -0700	[thread overview]
Message-ID: <20181024193402.16698-6-nicoleotsuka@gmail.com> (raw)
In-Reply-To: <20181024193402.16698-1-nicoleotsuka@gmail.com>

If all three channels are disabled via in[123]_enable ABI,
the driver could suspend the chip for power saving purpose.

So this patch adds the PM runtime support in order to gain
more power control than system suspend and resume use case.

For PM runtime, there are a few related changes happening:
1) Added a new explicit hdev device pointer for all the PM
   runtime callbacks. This is because hwmon core registers
   a child device for each hwmon driver. So there might be
   a mismatch between two device pointers in the driver if
   mixing using them.
2) Added a check in ina3221_is_enabled() to make sure that
   the chip is resumed.
3) Bypassed the unchanged status in ina3221_write_enable()
   in order to keep the PM runtime refcount being matched.
4) Removed the reset routine in the probe() by calling the
   resume() via pm_runtime_get_sync() instead, as they're
   similar. It's also necessary to do so to match initial
   PM refcount with the number of enabled channels.
5) Bypassed the system suspend/resume callbacks from the
   i2c_client->dev, because both the i2c_client->dev and
   the ina->hdev coexist and share the same pair of system
   suspend/resume callback functions, which means there'd
   be two suspend() calls during the system suspend while
   the second one will fail.

Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
---
Changelog
v2->v3:
 * Improved a dev_err message
 * Added comments at pm_runtime_put_noidle() callbacks
 * Added pm_runtime header file in an alphabetical order
v1->v2:
 * Bypassed i2c_client->dev in suspend/resume()
 * Added a missing '\n' in one dev_err()

 drivers/hwmon/ina3221.c | 113 ++++++++++++++++++++++++++++++++--------
 1 file changed, 91 insertions(+), 22 deletions(-)

diff --git a/drivers/hwmon/ina3221.c b/drivers/hwmon/ina3221.c
index 07dd6ef58d3e..3e7c6fac6e1b 100644
--- a/drivers/hwmon/ina3221.c
+++ b/drivers/hwmon/ina3221.c
@@ -20,6 +20,7 @@
 #include <linux/module.h>
 #include <linux/mutex.h>
 #include <linux/of.h>
+#include <linux/pm_runtime.h>
 #include <linux/regmap.h>
 
 #define INA3221_DRIVER_NAME		"ina3221"
@@ -53,6 +54,7 @@
 #define INA3221_CONFIG_CHs_EN_MASK	GENMASK(14, 12)
 #define INA3221_CONFIG_CHx_EN(x)	BIT(14 - (x))
 
+#define INA3221_CONFIG_DEFAULT		0x7127
 #define INA3221_RSHUNT_DEFAULT		10000
 
 enum ina3221_fields {
@@ -103,6 +105,7 @@ struct ina3221_input {
 
 /**
  * struct ina3221_data - device specific information
+ * @hdev: Device pointer of hwmon child device, used for pm runtime
  * @regmap: Register map of the device
  * @fields: Register fields of the device
  * @inputs: Array of channel input source specific structures
@@ -110,6 +113,7 @@ struct ina3221_input {
  * @reg_config: Register value of INA3221_CONFIG
  */
 struct ina3221_data {
+	struct device *hdev;
 	struct regmap *regmap;
 	struct regmap_field *fields[F_MAX_FIELDS];
 	struct ina3221_input inputs[INA3221_NUM_CHANNELS];
@@ -119,7 +123,8 @@ struct ina3221_data {
 
 static inline bool ina3221_is_enabled(struct ina3221_data *ina, int channel)
 {
-	return ina->reg_config & INA3221_CONFIG_CHx_EN(channel);
+	return pm_runtime_active(ina->hdev) &&
+	       (ina->reg_config & INA3221_CONFIG_CHx_EN(channel));
 }
 
 /* Lookup table for Bus and Shunt conversion times in usec */
@@ -290,21 +295,48 @@ static int ina3221_write_enable(struct device *dev, int channel, bool enable)
 {
 	struct ina3221_data *ina = dev_get_drvdata(dev);
 	u16 config, mask = INA3221_CONFIG_CHx_EN(channel);
+	u16 config_old = ina->reg_config & mask;
 	int ret;
 
 	config = enable ? mask : 0;
 
+	/* Bypass if enable status is not being changed */
+	if (config_old == config)
+		return 0;
+
+	/* For enabling routine, increase refcount and resume() at first */
+	if (enable) {
+		ret = pm_runtime_get_sync(ina->hdev);
+		if (ret < 0) {
+			dev_err(dev, "Failed to get PM runtime\n");
+			return ret;
+		}
+	}
+
 	/* Enable or disable the channel */
 	ret = regmap_update_bits(ina->regmap, INA3221_CONFIG, mask, config);
 	if (ret)
-		return ret;
+		goto fail;
 
 	/* Cache the latest config register value */
 	ret = regmap_read(ina->regmap, INA3221_CONFIG, &ina->reg_config);
 	if (ret)
-		return ret;
+		goto fail;
+
+	/* For disabling routine, decrease refcount or suspend() at last */
+	if (!enable)
+		pm_runtime_put_sync(ina->hdev);
 
 	return 0;
+
+fail:
+	if (enable) {
+		dev_err(dev, "Failed to enable channel %d: error %d\n",
+			channel, ret);
+		pm_runtime_put_sync(ina->hdev);
+	}
+
+	return ret;
 }
 
 static int ina3221_read(struct device *dev, enum hwmon_sensor_types type,
@@ -599,7 +631,6 @@ static int ina3221_probe(struct i2c_client *client,
 {
 	struct device *dev = &client->dev;
 	struct ina3221_data *ina;
-	struct device *hwmon_dev;
 	int i, ret;
 
 	ina = devm_kzalloc(dev, sizeof(*ina), GFP_KERNEL);
@@ -631,44 +662,72 @@ static int ina3221_probe(struct i2c_client *client,
 		return ret;
 	}
 
-	ret = regmap_field_write(ina->fields[F_RST], true);
-	if (ret) {
-		dev_err(dev, "Unable to reset device\n");
-		return ret;
-	}
-
-	/* Sync config register after reset */
-	ret = regmap_read(ina->regmap, INA3221_CONFIG, &ina->reg_config);
-	if (ret)
-		return ret;
+	/* The driver will be reset, so use reset value */
+	ina->reg_config = INA3221_CONFIG_DEFAULT;
 
 	/* Disable channels if their inputs are disconnected */
 	for (i = 0; i < INA3221_NUM_CHANNELS; i++) {
 		if (ina->inputs[i].disconnected)
 			ina->reg_config &= ~INA3221_CONFIG_CHx_EN(i);
 	}
-	ret = regmap_write(ina->regmap, INA3221_CONFIG, ina->reg_config);
-	if (ret)
-		return ret;
 
 	mutex_init(&ina->lock);
 	dev_set_drvdata(dev, ina);
 
-	hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name, ina,
+	/* Fence sysfs nodes till pm_runtime is resumed */
+	mutex_lock(&ina->lock);
+
+	/* Use the returned hdev for pm_runtime */
+	ina->hdev = devm_hwmon_device_register_with_info(dev, client->name, ina,
 							 &ina3221_chip_info,
 							 ina3221_groups);
-	if (IS_ERR(hwmon_dev)) {
+	if (IS_ERR(ina->hdev)) {
 		dev_err(dev, "Unable to register hwmon device\n");
-		mutex_destroy(&ina->lock);
-		return PTR_ERR(hwmon_dev);
+		ret = PTR_ERR(ina->hdev);
+		goto fail_lock;
 	}
 
+	/* Enable PM runtime -- status is suspended by default */
+	pm_runtime_enable(ina->hdev);
+
+	/* Initialize (resume) the device */
+	for (i = 0; i < INA3221_NUM_CHANNELS; i++) {
+		if (ina->inputs[i].disconnected)
+			continue;
+		/* Match the refcount with number of enabled channels */
+		ret = pm_runtime_get_sync(ina->hdev);
+		if (ret < 0)
+			goto fail_pm;
+	}
+
+	mutex_unlock(&ina->lock);
+
 	return 0;
+
+fail_pm:
+	pm_runtime_disable(ina->hdev);
+	pm_runtime_set_suspended(ina->hdev);
+	/* pm_runtime_put_noidle() will decrease the PM refcount until 0 */
+	for (i = 0; i < INA3221_NUM_CHANNELS; i++)
+		pm_runtime_put_noidle(ina->hdev);
+fail_lock:
+	mutex_unlock(&ina->lock);
+	mutex_destroy(&ina->lock);
+
+	return ret;
 }
 
 static int ina3221_remove(struct i2c_client *client)
 {
 	struct ina3221_data *ina = dev_get_drvdata(&client->dev);
+	int i;
+
+	pm_runtime_disable(ina->hdev);
+	pm_runtime_set_suspended(ina->hdev);
+
+	/* pm_runtime_put_noidle() will decrease the PM refcount until 0 */
+	for (i = 0; i < INA3221_NUM_CHANNELS; i++)
+		pm_runtime_put_noidle(ina->hdev);
 
 	mutex_destroy(&ina->lock);
 
@@ -680,6 +739,10 @@ static int __maybe_unused ina3221_suspend(struct device *dev)
 	struct ina3221_data *ina = dev_get_drvdata(dev);
 	int ret;
 
+	/* Let hdev control all PM runtime callbacks */
+	if (dev != ina->hdev)
+		return 0;
+
 	/* Save config register value and enable cache-only */
 	ret = regmap_read(ina->regmap, INA3221_CONFIG, &ina->reg_config);
 	if (ret)
@@ -703,6 +766,10 @@ static int __maybe_unused ina3221_resume(struct device *dev)
 	struct ina3221_data *ina = dev_get_drvdata(dev);
 	int ret;
 
+	/* Let hdev control all PM runtime callbacks */
+	if (dev != ina->hdev)
+		return 0;
+
 	regcache_cache_only(ina->regmap, false);
 
 	/* Software reset the chip */
@@ -726,7 +793,9 @@ static int __maybe_unused ina3221_resume(struct device *dev)
 }
 
 static const struct dev_pm_ops ina3221_pm = {
-	SET_SYSTEM_SLEEP_PM_OPS(ina3221_suspend, ina3221_resume)
+	SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+				pm_runtime_force_resume)
+	SET_RUNTIME_PM_OPS(ina3221_suspend, ina3221_resume, NULL)
 };
 
 static const struct of_device_id ina3221_of_match_table[] = {
-- 
2.17.1


      parent reply	other threads:[~2018-10-24 19:34 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-10-24 19:33 [PATCH v3 0/5] hwmon: (ina3221) Implement PM runtime to save power Nicolin Chen
2018-10-24 19:33 ` [PATCH v3 1/5] hwmon: (core) Inherit power properties to hdev Nicolin Chen
2018-10-25  0:13   ` linux
2018-10-25  1:01     ` Nicolin Chen
2018-10-25  1:33       ` Nicolin Chen
2018-10-25  6:55         ` linux
2018-10-25 23:21           ` Nicolin Chen
2018-10-24 19:33 ` [PATCH v3 2/5] hwmon: (ina3221) Check channel status for alarms attribute read Nicolin Chen
2018-10-24 19:34 ` [PATCH v3 3/5] hwmon: (ina3221) Serialize sysfs ABI accesses Nicolin Chen
2018-10-24 19:34 ` [PATCH v3 4/5] hwmon: (ina3221) Make sure data is ready before reading Nicolin Chen
2018-10-24 19:34 ` Nicolin Chen [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20181024193402.16698-6-nicoleotsuka@gmail.com \
    --to=nicoleotsuka@gmail.com \
    --cc=jdelvare@suse.com \
    --cc=linux-hwmon@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux@roeck-us.net \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).