From: Rob Herring <robh@kernel.org>
To: Sven Van Asbroeck <svendev@arcx.com>
Cc: lee.jones@linaro.org, mark.rutland@arm.com, afaerber@suse.de,
treding@nvidia.com, david@lechnology.com, noralf@tronnes.org,
johan@kernel.org, monstr@monstr.eu, michal.vokac@ysoft.com,
arnd@arndb.de, gregkh@linuxfoundation.org, john.garry@huawei.com,
andriy.shevchenko@linux.intel.com, geert+renesas@glider.be,
robin.murphy@arm.com, paul.gortmaker@windriver.com,
sebastien.bourdelin@savoirfairelinux.com, icenowy@aosc.io,
yuanzhichang@hisilicon.com, stuyoder@gmail.com,
linus.walleij@linaro.org, maxime.ripard@bootlin.com,
bogdan.purcareata@nxp.com, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org
Subject: Re: [PATCH anybus v1 2/4] dt-bindings: anybus-bridge: document devicetree binding.
Date: Wed, 24 Oct 2018 19:06:58 -0500 [thread overview]
Message-ID: <20181025000658.GA26048@bogus> (raw)
In-Reply-To: <20181024142456.10084-3-svendev@arcx.com>
On Wed, Oct 24, 2018 at 10:24:54AM -0400, Sven Van Asbroeck wrote:
> This patch adds devicetree binding documentation for the
> Arcx anybus bridge.
>
> Signed-off-by: Sven Van Asbroeck <svendev@arcx.com>
> ---
> .../bindings/mfd/arcx,anybus-bridge.txt | 37 +++++++++++++++++++
> .../devicetree/bindings/vendor-prefixes.txt | 1 +
> 2 files changed, 38 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/arcx,anybus-bridge.txt
>
> diff --git a/Documentation/devicetree/bindings/mfd/arcx,anybus-bridge.txt b/Documentation/devicetree/bindings/mfd/arcx,anybus-bridge.txt
> new file mode 100644
> index 000000000000..3c0399c4ed45
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/arcx,anybus-bridge.txt
> @@ -0,0 +1,37 @@
> +* Arcx anybus bridge
> +
> +This chip communicates with the SoC over the WEIM bus. It is
> +expected that its Device Tree node is specified as the child of a node
> +corresponding to the WEIM bus used for communication.
By WEIM you are referring to i.MX external parallel bus? Presumably this
can work on any parallel bus, not just i.MX.
> +
> +Required properties:
> +
> + - compatible : The following chip-specific string:
> + "arcx,anybus-bridge"
No version or part number?
> +
> + - reg :
> + weim memory area where the cpld registers are located, followed by:
> + weim memory area of the first anybus-s slot, followed by:
> + weim memory area of the second anybus-s slot.
> +
> + - enable-gpios : the gpio connected to the bridge's 'enable gpio'.
> +
> + - pwms : the pwm connected to the bridge's 'pwm input'.
> +
> + - irq-gpios : the gpios connected to the bridge's interrupt lines.
> + note that there is no need to provide the 'interrupts' property here.
Why not? This should not be base on what the OS currently happens to
support.
What are the functions of each line? The order must be defined.
> +
> +Example of usage:
> +
> +&weim {
> + bridge@0,0 {
> + compatible = "arcx,anybus-bridge";
> + reg = <0 0 0x100>, <0 0x400000 0x800>, <1 0x400000 0x800>;
> + fsl,weim-cs-timing = <0x024400b1 0x00001010 0x20081100
> + 0x00000000 0xa0000240 0x00000000>;
> + enable-gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
> + pwms = <&pwm3 0 571>;
> + irq-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>,
> + <&gpio1 5 GPIO_ACTIVE_HIGH>;
> + };
> +};
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> index 2c3fc512e746..1bf07b20a8af 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> @@ -35,6 +35,7 @@ aptina Aptina Imaging
> arasan Arasan Chip Systems
> archermind ArcherMind Technology (Nanjing) Co., Ltd.
> arctic Arctic Sand
> +arcx Arcx/Archronix Inc.
> aries Aries Embedded GmbH
> arm ARM Ltd.
> armadeus ARMadeus Systems SARL
> --
> 2.17.1
>
next prev parent reply other threads:[~2018-10-25 0:07 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-10-24 14:24 [PATCH anybus v1 0/4] Support HMS Profinet Card over Anybus Sven Van Asbroeck
2018-10-24 14:24 ` [PATCH anybus v1 1/4] mfd: support the Arcx anybus bridge Sven Van Asbroeck
2018-10-24 15:58 ` Randy Dunlap
2018-10-26 8:34 ` Lee Jones
2018-10-26 13:40 ` Sven Van Asbroeck
2018-10-24 14:24 ` [PATCH anybus v1 2/4] dt-bindings: anybus-bridge: document devicetree binding Sven Van Asbroeck
2018-10-25 0:06 ` Rob Herring [this message]
2018-10-25 5:19 ` Lee Jones
2018-10-25 10:16 ` Linus Walleij
2018-10-24 14:24 ` [PATCH anybus v1 3/4] bus: support HMS Anybus-S bus Sven Van Asbroeck
2018-10-24 15:58 ` Randy Dunlap
2018-10-25 11:08 ` Linus Walleij
2018-10-24 14:24 ` [PATCH anybus v1 4/4] misc: support HMS Profinet IRT industrial controller Sven Van Asbroeck
2018-10-24 15:58 ` Randy Dunlap
2018-10-25 9:18 ` [PATCH anybus v1 0/4] Support HMS Profinet Card over Anybus Andy Shevchenko
2018-11-05 14:49 ` Sven Van Asbroeck
2018-10-25 13:35 [PATCH anybus v1 2/4] dt-bindings: anybus-bridge: document devicetree binding thesven73
2018-10-25 13:55 thesven73
2018-10-25 15:30 ` David Lechner
2018-10-26 11:28 ` Linus Walleij
2018-10-25 15:46 thesven73
2018-10-26 6:39 ` Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181025000658.GA26048@bogus \
--to=robh@kernel.org \
--cc=afaerber@suse.de \
--cc=andriy.shevchenko@linux.intel.com \
--cc=arnd@arndb.de \
--cc=bogdan.purcareata@nxp.com \
--cc=david@lechnology.com \
--cc=devicetree@vger.kernel.org \
--cc=geert+renesas@glider.be \
--cc=gregkh@linuxfoundation.org \
--cc=icenowy@aosc.io \
--cc=johan@kernel.org \
--cc=john.garry@huawei.com \
--cc=lee.jones@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=maxime.ripard@bootlin.com \
--cc=michal.vokac@ysoft.com \
--cc=monstr@monstr.eu \
--cc=noralf@tronnes.org \
--cc=paul.gortmaker@windriver.com \
--cc=robin.murphy@arm.com \
--cc=sebastien.bourdelin@savoirfairelinux.com \
--cc=stuyoder@gmail.com \
--cc=svendev@arcx.com \
--cc=treding@nvidia.com \
--cc=yuanzhichang@hisilicon.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).