Re: [PATCH v4 0/9] staging: iio: ad7780: move out of staging

[Renato Lui Geh <renatogeh@gmail.com>]

Hi Alexandru,

Thanks for the review. Some questions inline.

Thanks,
Renato

On 03/01, Ardelean, Alexandru wrote:
>On Thu, 2019-02-28 at 11:23 -0300, Renato Lui Geh wrote:
>>
>
>The patch-series is a bit big.
>I guess that the intent is to move this out-of-staging, but various patches
>are holding this in it's place.
>For patch series above a certain size, you could get many re-spins
>[V2,3,4... so on].
>
>You could send some of the changes as individual patches, or group them in
>series of 1,2 or 3 patches. That way, you "parallelize" patch sending, and
>when you get reviews on each patch, you can re-spin them individually.
>You'll find over time that certain patches get accepted on V1, others on V2
>and some on V7 [ hopefully, there isn't any frustration at that point ].

On these subseries, should versioning follow this patchset (v5) or should
they start anew (v1), ignoring this series version?
>
>Well, this is a technique I use to distribute some of my upstream-patch-
>work, so that I can switch easier between internal-work & upstreaming-work.
>
>Coming back to this patch-series.
>My general input, is that the patches are fine over-all; some are just
>cosmetics/noise/a-different-way-of-doing-things-for-this-driver, and those
>usually can be left to preference [of the maintainer usually].
>
>I do suggest to not hurry when re-spinning patches, and not change too much
>the number of patches in a new series. That can complicate things
>sometimes. But, if doing small patch-series or individual patches, you
>won't have this problem too much.
>
>Thanks
>Alex
>
>>
>> This series of patches contains the following:
>>  - Adds user input for the 'gain' and 'filter' GPIO pins for the ad778x
>>    family chips;
>>  - Filter reading for the ad778x;
>>  - Sets pattern macro values and mask for PATTERN status bits;
>>  - Adds ID values for the ad7170, ad7171, ad7780 and ad7781 for ID
>>    status bits checking;
>>  - Moves regulator initialization to after GPIO init to maintain
>>    consistency between probe and remove;
>>  - Copyright edits, adding SPDX identifier and new copyright holder;
>>  - Moves the ad7780 driver out of staging to the mainline;
>>  - Adds device tree binding for the ad7780 driver.
>>
>> Renato Lui Geh (9):
>>   staging: iio: ad7780: add gain & filter gpio support
>>   staging: iio: ad7780: add filter reading to ad778x
>>   staging: iio: ad7780: set pattern values and masks directly
>>   staging:iio:ad7780: add chip ID values and mask
>>   staging: iio: ad7780: move regulator to after GPIO init
>>   staging: iio: ad7780: add SPDX identifier
>>   staging: iio: ad7780: add new copyright holder
>>   staging: iio: ad7780: moving ad7780 out of staging
>>   staging: iio: ad7780: add device tree binding
>>
>> Changelog:
>> *v3
>>  - SPDX and regulator init as patches
>>  - Renamed filter to odr and ad778x_filter to ad778x_odr_avail
>>  - Removed unnecessary regulator disabling
>>  - Removed unnecessary AD_SD_CHANNEL macro
>>  - Changed unsigned int to unsigned long long to avoid overflow
>> *v4
>>  - Split gain & filter patch into two, with the new commit adding only
>>    filter reading
>>  - Changed pattern values to direct values, and added pattern mask
>>  - Added ID values and mask
>>  - Added new copyright holder
>>  - Added device tree binding to the ad7780 driver
>>
>>  .../bindings/iio/adc/adi,ad7780.txt           |  48 +++
>>  drivers/iio/adc/Kconfig                       |  12 +
>>  drivers/iio/adc/Makefile                      |   1 +
>>  drivers/iio/adc/ad7780.c                      | 365 ++++++++++++++++++
>>  drivers/staging/iio/adc/Kconfig               |  13 -
>>  drivers/staging/iio/adc/Makefile              |   1 -
>>  drivers/staging/iio/adc/ad7780.c              | 277 -------------
>>  7 files changed, 426 insertions(+), 291 deletions(-)
>>  create mode 100644
>> Documentation/devicetree/bindings/iio/adc/adi,ad7780.txt
>>  create mode 100644 drivers/iio/adc/ad7780.c
>>  delete mode 100644 drivers/staging/iio/adc/ad7780.c
>>
>> --
>> 2.21.0
>>
>
>-- 
>You received this message because you are subscribed to the Google Groups "Kernel USP" group.
>To unsubscribe from this group and stop receiving emails from it, send an email to kernel-usp+unsubscribe@googlegroups.com.
>To post to this group, send email to kernel-usp@googlegroups.com.
>To view this discussion on the web visit https://groups.google.com/d/msgid/kernel-usp/72a54cd5f58aeb9507b95b7e33ca3d9a38c853e9.camel%40analog.com.
>For more options, visit https://groups.google.com/d/optout.