From: Tony Lindgren <tony@atomide.com>
To: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Mark Brown <broonie@kernel.org>,
Liam Girdwood <lgirdwood@gmail.com>,
Jaroslav Kysela <perex@perex.cz>, Takashi Iwai <tiwai@suse.com>,
alsa-devel@alsa-project.org, linux-kernel@vger.kernel.org,
linux-omap@vger.kernel.org, "Arthur D ." <spinal.by@gmail.com>,
Merlijn Wajer <merlijn@wizzup.org>, Pavel Machek <pavel@ucw.cz>,
Sebastian Reichel <sre@kernel.org>,
Jarkko Nikula <jarkko.nikula@bitmer.com>
Subject: Re: [PATCH] ASoC: cpcap: Implement set_tdm_slot for voice call support
Date: Mon, 17 Feb 2020 15:23:25 -0800 [thread overview]
Message-ID: <20200217232325.GD35972@atomide.com> (raw)
In-Reply-To: <9a060430-5a3e-61e1-3d2c-f89819d9436f@ti.com>
* Peter Ujfalusi <peter.ujfalusi@ti.com> [200214 13:30]:
> Hi Tony,
>
> On 12/02/2020 16.46, Tony Lindgren wrote:
> > * Peter Ujfalusi <peter.ujfalusi@ti.com> [200212 09:18]:
> >> On 11/02/2020 20.10, Tony Lindgren wrote:
> >>> +static int cpcap_voice_set_tdm_slot(struct snd_soc_dai *dai,
> >>> + unsigned int tx_mask, unsigned int rx_mask,
> >>> + int slots, int slot_width)
> >>> +{
> >>> + struct snd_soc_component *component = dai->component;
> >>> + struct cpcap_audio *cpcap = snd_soc_component_get_drvdata(component);
> >>> + int err, ts_mask, mask;
> >>> + bool voice_call;
> >>> +
> >>> + /*
> >>> + * Primitive test for voice call, probably needs more checks
> >>> + * later on for 16-bit calls detected, Bluetooth headset etc.
> >>> + */
> >>> + if (tx_mask == 0 && rx_mask == 1 && slot_width == 8)
> >>> + voice_call = true;
> >>> + else
> >>> + voice_call = false;
> >>
> >> You only have voice call if only rx slot0 is in use?
> >
> > Yeah so it seems. Then there's the modem to wlcore bluetooth path that
> > I have not looked at. But presumably that's again just configuring some
> > tdm slot on the PMIC.
> >
> >> If you record mono on the voice DAI, then rx_mask is also 1, no?
> >
> > It is above :) But maybe I don't follow what you're asking here
>
> If you arecrod -Dvoice_pcm -c1 -fS8 > /dev/null
> then it is reasonable that the machine driver will set rx_mask = 1
>
> > and maybe you have some better check in mind.
>
> Not sure, but relying on set_tdm_slots to decide if we are in a call
> case does not sound right.
OK yeah seems at least bluetooth would need to be also handled
in the set_tdm_slots.
> >> You will also set the sampling rate for voice in
> >> cpcap_voice_hw_params(), but that is for normal playback/capture, right?
> >
> > Yeah so normal playback/capture is already working with cpcap codec driver
> > with mainline Linux. The voice call needs to set rate to 8000.
>
> But if you have a voice call initiated should not the rate be set by the
> set_sysclk()?
Hmm does set_sysclk called from modem codec know that cpcap codec
is the clock master based on bitclock-master and set the rate
for cpcap codec?
> >> It feels like that these should be done via DAPM with codec to codec route?
> >
> > Sure if you have some better way of doing it :) Do you have an example to
> > point me to?
>
> Something along the lines of:
> https://mailman.alsa-project.org/pipermail/alsa-devel/2020-February/162915.html
>
> The it is a matter of building and connecting the DAPM routes between
> the two codec and with a flip of the switch you would have audio flowing
> between them.
Sounds good to me.
Tony
next prev parent reply other threads:[~2020-02-17 23:23 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-02-11 18:10 [PATCH] ASoC: cpcap: Implement set_tdm_slot for voice call support Tony Lindgren
2020-02-12 9:17 ` Peter Ujfalusi
2020-02-12 14:46 ` Tony Lindgren
2020-02-14 13:29 ` Peter Ujfalusi
2020-02-17 23:23 ` Tony Lindgren [this message]
2020-02-18 15:15 ` Peter Ujfalusi
2020-02-18 15:32 ` Tony Lindgren
2020-02-18 16:44 ` Mark Brown
2020-02-18 17:06 ` Sebastian Reichel
2020-02-18 17:42 ` Mark Brown
2020-02-19 17:39 ` Tony Lindgren
2020-02-19 17:46 ` Mark Brown
2020-02-19 18:49 ` Tony Lindgren
2020-02-19 18:53 ` Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200217232325.GD35972@atomide.com \
--to=tony@atomide.com \
--cc=alsa-devel@alsa-project.org \
--cc=broonie@kernel.org \
--cc=jarkko.nikula@bitmer.com \
--cc=lgirdwood@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=merlijn@wizzup.org \
--cc=pavel@ucw.cz \
--cc=perex@perex.cz \
--cc=peter.ujfalusi@ti.com \
--cc=spinal.by@gmail.com \
--cc=sre@kernel.org \
--cc=tiwai@suse.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).