From: muhammad.husaini.zulkifli@intel.com
To: adrian.hunter@intel.com, michal.simek@xilinx.com,
andriy.shevchenko@intel.com, ulf.hansson@linaro.org,
linux-mmc@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Cc: lakshmi.bai.raja.subramanian@intel.com,
wan.ahmad.zainie.wan.mohamad@intel.com,
muhammad.husaini.zulkifli@intel.com, arnd@arndb.de
Subject: [PATCH v4 4/4] mmc: sdhci-of-arasan: Enable UHS-1 support for Keem Bay SOC
Date: Thu, 8 Oct 2020 10:09:36 +0800 [thread overview]
Message-ID: <20201008020936.19894-5-muhammad.husaini.zulkifli@intel.com> (raw)
In-Reply-To: <20201008020936.19894-1-muhammad.husaini.zulkifli@intel.com>
From: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Voltage switching sequence is needed to support UHS-1 interface.
There are 2 places to control the voltage.
1) By setting the AON register using firmware driver calling
system-level platform management layer (SMC) to set the register.
2) By controlling the GPIO expander value to drive either 1.8V or 3.3V
for power mux input.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
---
drivers/mmc/host/sdhci-of-arasan.c | 126 +++++++++++++++++++++++++++++
1 file changed, 126 insertions(+)
diff --git a/drivers/mmc/host/sdhci-of-arasan.c b/drivers/mmc/host/sdhci-of-arasan.c
index 46aea6516133..ea2467b0073d 100644
--- a/drivers/mmc/host/sdhci-of-arasan.c
+++ b/drivers/mmc/host/sdhci-of-arasan.c
@@ -16,6 +16,7 @@
*/
#include <linux/clk-provider.h>
+#include <linux/gpio/consumer.h>
#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/of_device.h>
@@ -23,6 +24,7 @@
#include <linux/regmap.h>
#include <linux/of.h>
#include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/firmware/intel/keembay_firmware.h>
#include "cqhci.h"
#include "sdhci-pltfm.h"
@@ -136,6 +138,7 @@ struct sdhci_arasan_clk_data {
* @soc_ctl_base: Pointer to regmap for syscon for soc_ctl registers.
* @soc_ctl_map: Map to get offsets into soc_ctl registers.
* @quirks: Arasan deviations from spec.
+ * @uhs_gpio: Pointer to the uhs gpio.
*/
struct sdhci_arasan_data {
struct sdhci_host *host;
@@ -150,6 +153,7 @@ struct sdhci_arasan_data {
struct regmap *soc_ctl_base;
const struct sdhci_arasan_soc_ctl_map *soc_ctl_map;
unsigned int quirks;
+ struct gpio_desc *uhs_gpio;
/* Controller does not have CD wired and will not function normally without */
#define SDHCI_ARASAN_QUIRK_FORCE_CDTEST BIT(0)
@@ -361,6 +365,112 @@ static int sdhci_arasan_voltage_switch(struct mmc_host *mmc,
return -EINVAL;
}
+static int sdhci_arasan_keembay_voltage_switch(struct mmc_host *mmc,
+ struct mmc_ios *ios)
+{
+ struct sdhci_host *host = mmc_priv(mmc);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
+ u16 ctrl_2, clk;
+ int ret;
+
+ switch (ios->signal_voltage) {
+ case MMC_SIGNAL_VOLTAGE_180:
+ clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+ clk &= ~SDHCI_CLOCK_CARD_EN;
+ sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
+
+ clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+ if (clk & SDHCI_CLOCK_CARD_EN)
+ return -EAGAIN;
+
+ sdhci_writeb(host, SDHCI_POWER_ON | SDHCI_POWER_180,
+ SDHCI_POWER_CONTROL);
+
+ /*
+ * Set VDDIO_B voltage to Low for 1.8V
+ * which is controlling by GPIO Expander.
+ */
+ gpiod_set_value_cansleep(sdhci_arasan->uhs_gpio, 0);
+
+ /*
+ * This is like a final gatekeeper. Need to ensure changed voltage
+ * is settled before and after turn on this bit.
+ */
+ usleep_range(1000, 1100);
+
+ ret = keembay_sd_voltage_selection(KEEMBAY_SET_1V8_VOLT);
+ if (ret)
+ return ret;
+
+ usleep_range(1000, 1100);
+
+ ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+ ctrl_2 |= SDHCI_CTRL_VDD_180;
+ sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
+
+ /* Sleep for 5ms to stabilize 1.8V regulator */
+ usleep_range(5000, 5500);
+
+ /* 1.8V regulator output should be stable within 5 ms */
+ ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+ if (!(ctrl_2 & SDHCI_CTRL_VDD_180))
+ return -EAGAIN;
+
+ clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+ clk |= SDHCI_CLOCK_CARD_EN;
+ sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
+ break;
+ case MMC_SIGNAL_VOLTAGE_330:
+ /*
+ * Set VDDIO_B voltage to High for 3.3V
+ * which is controlling by GPIO Expander.
+ */
+ gpiod_set_value_cansleep(sdhci_arasan->uhs_gpio, 1);
+
+ /*
+ * This is like a final gatekeeper. Need to ensure changed voltage
+ * is settled before and after turn on this bit.
+ */
+ usleep_range(1000, 1100);
+
+ ret = keembay_sd_voltage_selection(KEEMBAY_SET_3V3_VOLT);
+ if (ret)
+ return ret;
+
+ usleep_range(1000, 1100);
+
+ /* Set 1.8V Signal Enable in the Host Control2 register to 0 */
+ ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+ ctrl_2 &= ~SDHCI_CTRL_VDD_180;
+ sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
+
+ /* Sleep for 5ms to stabilize 3.3V regulator */
+ usleep_range(5000, 5500);
+
+ /* 3.3V regulator output should be stable within 5 ms */
+ ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+ if (ctrl_2 & SDHCI_CTRL_VDD_180)
+ return -EAGAIN;
+
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int sdhci_arasan_keembay_select_drive_strength(struct mmc_card *card,
+ unsigned int max_dtr, int host_drv,
+ int card_drv, int *drv_type)
+{
+ if (card->host->ios.signal_voltage == MMC_SIGNAL_VOLTAGE_180)
+ *drv_type = MMC_SET_DRIVER_TYPE_C;
+
+ return 0;
+}
+
static const struct sdhci_ops sdhci_arasan_ops = {
.set_clock = sdhci_arasan_set_clock,
.get_max_clock = sdhci_pltfm_clk_get_max_clock,
@@ -1601,6 +1711,22 @@ static int sdhci_arasan_probe(struct platform_device *pdev)
host->mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY;
}
+ if (of_device_is_compatible(np, "intel,keembay-sdhci-5.1-sd")) {
+ struct gpio_desc *uhs;
+
+ uhs = devm_gpiod_get_optional(dev, "uhs", GPIOD_OUT_HIGH);
+ if (IS_ERR(uhs))
+ return dev_err_probe(dev, PTR_ERR(uhs), "can't get uhs gpio\n");
+
+ sdhci_arasan->uhs_gpio = uhs;
+
+ host->mmc_host_ops.start_signal_voltage_switch =
+ sdhci_arasan_keembay_voltage_switch;
+
+ host->mmc_host_ops.select_drive_strength =
+ sdhci_arasan_keembay_select_drive_strength;
+ }
+
sdhci_arasan_update_baseclkfreq(host);
ret = sdhci_arasan_register_sdclk(sdhci_arasan, clk_xin, &pdev->dev);
--
2.17.1
next prev parent reply other threads:[~2020-10-08 2:13 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-10-08 2:09 [PATCH v4 0/4] mmc: sdhci-of-arasan: Enable UHS-1 support for Keem Bay SOC muhammad.husaini.zulkifli
2020-10-08 2:09 ` [PATCH v4 1/4] firmware: keembay: Add support for Arm Trusted Firmware Service call muhammad.husaini.zulkifli
2020-10-08 7:35 ` Michal Simek
2020-10-08 8:46 ` Andy Shevchenko
2020-10-08 10:39 ` Zulkifli, Muhammad Husaini
2020-10-08 9:45 ` Sudeep Holla
2020-10-08 12:34 ` Zulkifli, Muhammad Husaini
2020-10-08 2:09 ` [PATCH v4 2/4] dt-bindings: mmc: Add uhs-gpio for Keem Bay UHS-1 Support muhammad.husaini.zulkifli
2020-10-08 7:36 ` Michal Simek
2020-10-08 2:09 ` [PATCH v4 3/4] mmc: sdhci-of-arasan: Add structure device pointer in probe muhammad.husaini.zulkifli
2020-10-08 7:34 ` Michal Simek
2020-10-08 10:36 ` Zulkifli, Muhammad Husaini
2020-10-08 11:12 ` Andy Shevchenko
2020-10-08 2:09 ` muhammad.husaini.zulkifli [this message]
2020-10-08 7:36 ` [PATCH v4 4/4] mmc: sdhci-of-arasan: Enable UHS-1 support for Keem Bay SOC Michal Simek
2020-10-08 9:27 ` Ulf Hansson
2020-10-08 10:54 ` Zulkifli, Muhammad Husaini
2020-10-08 15:19 ` Ulf Hansson
2020-10-08 17:21 ` Zulkifli, Muhammad Husaini
2020-10-09 6:56 ` Ulf Hansson
2020-10-09 7:25 ` Michal Simek
2020-10-09 17:50 ` Zulkifli, Muhammad Husaini
2020-10-13 8:12 ` Zulkifli, Muhammad Husaini
2020-10-13 8:41 ` Ulf Hansson
2020-10-16 7:23 ` Zulkifli, Muhammad Husaini
2020-10-16 10:50 ` Ulf Hansson
2020-11-06 7:16 ` Zulkifli, Muhammad Husaini
2020-11-09 13:36 ` Zulkifli, Muhammad Husaini
2020-10-08 10:58 ` Adrian Hunter
2020-10-08 15:12 ` Ulf Hansson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201008020936.19894-5-muhammad.husaini.zulkifli@intel.com \
--to=muhammad.husaini.zulkifli@intel.com \
--cc=adrian.hunter@intel.com \
--cc=andriy.shevchenko@intel.com \
--cc=arnd@arndb.de \
--cc=lakshmi.bai.raja.subramanian@intel.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=michal.simek@xilinx.com \
--cc=ulf.hansson@linaro.org \
--cc=wan.ahmad.zainie.wan.mohamad@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).