From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
To: Geert Uytterhoeven <geert+renesas@glider.be>,
Magnus Damm <magnus.damm@gmail.com>,
Rob Herring <robh+dt@kernel.org>
Cc: linux-renesas-soc@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Biju Das <biju.das.jz@bp.renesas.com>,
Prabhakar <prabhakar.csengg@gmail.com>,
Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Subject: [PATCH] ARM: dts: r8a7742-iwg21d-q7-dbcm-ca: Add OV7725 nodes
Date: Fri, 20 Nov 2020 15:13:43 +0000 [thread overview]
Message-ID: <20201120151343.24175-1-prabhakar.mahadev-lad.rj@bp.renesas.com> (raw)
Add the ov7725 endpoint nodes to the camera daughter board. The ov7725
sensors can be populated on I2C{0,1,2,3} buses.
By default the VIN{0,1,2,3} are tied to OV5640{0,1,2,3} endpoints
respectively in the camera DB dts hence the remote-endpoint property in
OV7725{0,1,2,3} endpoints is commented out.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
---
Hi All,
This patch is based on top of [1].
[1] https://git.kernel.org/pub/scm/linux/kernel/git/geert/
renesas-devel.git/log/?h=renesas-arm-dt-for-v5.11
Cheers,
Prabhakar
---
.../boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts | 93 +++++++++++++++++++
1 file changed, 93 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
index 98c3fbd89fa6..d1386bf7bdbe 100644
--- a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
+++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
@@ -108,6 +108,29 @@
};
};
};
+
+ ov7725@21 {
+ compatible = "ovti,ov7725";
+ reg = <0x21>;
+ clocks = <&mclk_cam1>;
+
+ port {
+ ov7725_0: endpoint {
+ bus-width = <8>;
+ bus-type = <6>;
+ /*
+ * uncomment remote-endpoint property to
+ * tie ov7725_0 to vin0ep also make
+ * sure to comment/remove remote-endpoint
+ * property from ov5640_0 endpoint and
+ * replace remote-endpoint property in
+ * vin0ep node with
+ * remote-endpoint = <&ov7725_0>;
+ */
+ /* remote-endpoint = <&vin0ep>; */
+ };
+ };
+ };
};
&i2c1 {
@@ -133,6 +156,29 @@
};
};
};
+
+ ov7725@21 {
+ compatible = "ovti,ov7725";
+ reg = <0x21>;
+ clocks = <&mclk_cam2>;
+
+ port {
+ ov7725_1: endpoint {
+ bus-width = <8>;
+ bus-type = <6>;
+ /*
+ * uncomment remote-endpoint property to
+ * tie ov7725_1 to vin1ep also make
+ * sure to comment/remove remote-endpoint
+ * property from ov5640_1 endpoint and
+ * replace remote-endpoint property in
+ * vin1ep node with
+ * remote-endpoint = <&ov7725_1>;
+ */
+ /* remote-endpoint = <&vin1ep>; */
+ };
+ };
+ };
};
&i2c2 {
@@ -152,6 +198,30 @@
};
};
};
+
+ ov7725@21 {
+ status = "disabled";
+ compatible = "ovti,ov7725";
+ reg = <0x21>;
+ clocks = <&mclk_cam3>;
+
+ port {
+ ov7725_2: endpoint {
+ bus-width = <8>;
+ bus-type = <6>;
+ /*
+ * uncomment remote-endpoint property to
+ * tie ov7725_2 to vin2ep also make
+ * sure to comment/remove remote-endpoint
+ * property from ov5640_2 endpoint and
+ * replace remote-endpoint property in
+ * vin2ep node with
+ * remote-endpoint = <&ov7725_2>;
+ */
+ /* remote-endpoint = <&vin2ep>; */
+ };
+ };
+ };
};
&i2c3 {
@@ -177,6 +247,29 @@
};
};
};
+
+ ov7725@21 {
+ compatible = "ovti,ov7725";
+ reg = <0x21>;
+ clocks = <&mclk_cam4>;
+
+ port {
+ ov7725_3: endpoint {
+ bus-width = <8>;
+ bus-type = <6>;
+ /*
+ * uncomment remote-endpoint property to
+ * tie ov7725_3 to vin3ep also make
+ * sure to comment/remove remote-endpoint
+ * property from ov5640_3 endpoint and
+ * replace remote-endpoint property in
+ * vin3ep node with
+ * remote-endpoint = <&ov7725_3>;
+ */
+ /* remote-endpoint = <&vin3ep>; */
+ };
+ };
+ };
};
&pfc {
--
2.17.1
next reply other threads:[~2020-11-20 15:14 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-11-20 15:13 Lad Prabhakar [this message]
2020-11-24 9:04 ` [PATCH] ARM: dts: r8a7742-iwg21d-q7-dbcm-ca: Add OV7725 nodes Geert Uytterhoeven
2020-11-24 13:51 ` Lad, Prabhakar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201120151343.24175-1-prabhakar.mahadev-lad.rj@bp.renesas.com \
--to=prabhakar.mahadev-lad.rj@bp.renesas.com \
--cc=biju.das.jz@bp.renesas.com \
--cc=devicetree@vger.kernel.org \
--cc=geert+renesas@glider.be \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=magnus.damm@gmail.com \
--cc=prabhakar.csengg@gmail.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).