From: Maxime Ripard <maxime@cerno.tech>
To: Eric Anholt <eric@anholt.net>,
Maarten Lankhorst <maarten.lankhorst@linux.intel.com>,
Thomas Zimmermann <tzimmermann@suse.de>,
Maxime Ripard <maxime@cerno.tech>,
Daniel Vetter <daniel.vetter@intel.com>,
David Airlie <airlied@linux.ie>
Cc: Jason Cooper <jason@lakedaemon.net>,
bcm-kernel-feedback-list@broadcom.com,
linux-arm-kernel@lists.infradead.org,
Marc Zyngier <maz@kernel.org>,
linux-media@vger.kernel.org,
Hans Verkuil <hverkuil-cisco@xs4all.nl>,
linux-kernel@vger.kernel.org,
Mauro Carvalho Chehab <mchehab@kernel.org>,
Thomas Gleixner <tglx@linutronix.de>,
Dave Stevenson <dave.stevenson@raspberrypi.com>,
linux-rpi-kernel@lists.infradead.org,
dri-devel@lists.freedesktop.org
Subject: [PATCH 15/15] ARM: dts: bcm2711: Add the CEC interrupt controller
Date: Thu, 10 Dec 2020 14:46:48 +0100 [thread overview]
Message-ID: <20201210134648.272857-16-maxime@cerno.tech> (raw)
In-Reply-To: <20201210134648.272857-1-maxime@cerno.tech>
The CEC and hotplug interrupts go through an interrupt controller shared
between the two HDMI controllers.
Let's add that interrupt controller and the interrupts for both HDMI
controllers
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
arch/arm/boot/dts/bcm2711.dtsi | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/arch/arm/boot/dts/bcm2711.dtsi b/arch/arm/boot/dts/bcm2711.dtsi
index 8bb46ae76a92..154cf6d35333 100644
--- a/arch/arm/boot/dts/bcm2711.dtsi
+++ b/arch/arm/boot/dts/bcm2711.dtsi
@@ -316,6 +316,14 @@ bsc_intr: interrupt-controller@7ef00040 {
#interrupt-cells = <1>;
};
+ aon_intr: interrupt-controller@7ef00100 {
+ compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc";
+ reg = <0x7ef00100 0x30>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
hdmi0: hdmi@7ef00700 {
compatible = "brcm,bcm2711-hdmi0";
reg = <0x7ef00700 0x300>,
@@ -338,6 +346,11 @@ hdmi0: hdmi@7ef00700 {
"hd";
clock-names = "hdmi", "bvb", "audio", "cec";
resets = <&dvp 0>;
+ interrupt-parent = <&aon_intr>;
+ interrupts = <0>, <1>, <2>,
+ <3>, <4>, <5>;
+ interrupt-names = "cec-tx", "cec-rx", "cec-low",
+ "wakeup", "hpd-connected", "hpd-removed";
ddc = <&ddc0>;
dmas = <&dma 10>;
dma-names = "audio-rx";
@@ -377,6 +390,11 @@ hdmi1: hdmi@7ef05700 {
ddc = <&ddc1>;
clock-names = "hdmi", "bvb", "audio", "cec";
resets = <&dvp 1>;
+ interrupt-parent = <&aon_intr>;
+ interrupts = <6>, <7>, <8>,
+ <9>, <10>, <11>;
+ interrupt-names = "cec-tx", "cec-rx", "cec-low",
+ "wakeup", "hpd-connected", "hpd-removed";
dmas = <&dma 17>;
dma-names = "audio-rx";
status = "disabled";
--
2.28.0
next prev parent reply other threads:[~2020-12-10 13:50 UTC|newest]
Thread overview: 39+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-12-10 13:46 [PATCH 00/15] drm/vc4: hdmi: Add CEC support for the BCM2711 Maxime Ripard
2020-12-10 13:46 ` [PATCH 01/15] irqchip: Allow to compile bcmstb on other platforms Maxime Ripard
2020-12-10 17:33 ` Florian Fainelli
2020-12-10 17:59 ` Marc Zyngier
2020-12-14 15:27 ` Maxime Ripard
2020-12-14 16:20 ` Marc Zyngier
2020-12-10 13:46 ` [PATCH 02/15] drm/vc4: hdmi: Move hdmi reset to bind Maxime Ripard
2020-12-18 11:20 ` Dave Stevenson
2020-12-10 13:46 ` [PATCH 03/15] drm/vc4: hdmi: Fix register offset with longer CEC messages Maxime Ripard
2020-12-15 11:23 ` Dave Stevenson
2020-12-10 13:46 ` [PATCH 04/15] drm/vc4: hdmi: Fix up CEC registers Maxime Ripard
2020-12-18 11:21 ` Dave Stevenson
2020-12-10 13:46 ` [PATCH 05/15] drm/vc4: hdmi: Restore cec physical address on reconnect Maxime Ripard
2020-12-18 14:21 ` Dave Stevenson
2020-12-18 14:45 ` Dave Stevenson
2021-01-11 10:29 ` Maxime Ripard
2020-12-10 13:46 ` [PATCH 06/15] drm/vc4: hdmi: Compute the CEC clock divider from the clock rate Maxime Ripard
2020-12-18 11:30 ` Dave Stevenson
2020-12-10 13:46 ` [PATCH 07/15] drm/vc4: hdmi: Update the CEC clock divider on HSM rate change Maxime Ripard
2020-12-18 14:26 ` Dave Stevenson
2020-12-10 13:46 ` [PATCH 08/15] drm/vc4: hdmi: Introduce a CEC clock Maxime Ripard
2020-12-18 11:37 ` Dave Stevenson
2020-12-18 12:23 ` Maxime Ripard
2020-12-18 12:25 ` Dave Stevenson
2020-12-10 13:46 ` [PATCH 09/15] drm/vc4: hdmi: Split the interrupt handlers Maxime Ripard
2020-12-10 13:46 ` [PATCH 10/15] drm/vc4: hdmi: Support BCM2711 CEC interrupt setup Maxime Ripard
2020-12-10 13:46 ` [PATCH 11/15] drm/vc4: hdmi: Remove cec_available flag Maxime Ripard
2020-12-18 14:30 ` Dave Stevenson
2020-12-10 13:46 ` [PATCH 12/15] drm/vc4: hdmi: Don't register the CEC adapter if there's no interrupts Maxime Ripard
2020-12-18 14:29 ` Dave Stevenson
2020-12-10 13:46 ` [PATCH 13/15] dt-binding: display: bcm2711-hdmi: Add CEC and hotplug interrupts Maxime Ripard
2020-12-10 13:46 ` [PATCH 14/15] ARM: dts: bcm2711: Add the BSC interrupt controller Maxime Ripard
2020-12-10 17:41 ` Florian Fainelli
2020-12-10 13:46 ` Maxime Ripard [this message]
2020-12-10 17:42 ` [PATCH 15/15] ARM: dts: bcm2711: Add the CEC " Florian Fainelli
2020-12-16 12:35 ` [PATCH 00/15] drm/vc4: hdmi: Add CEC support for the BCM2711 Hans Verkuil
2020-12-17 10:49 ` Maxime Ripard
2020-12-17 10:53 ` Hans Verkuil
2020-12-17 12:59 ` Maxime Ripard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201210134648.272857-16-maxime@cerno.tech \
--to=maxime@cerno.tech \
--cc=airlied@linux.ie \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=daniel.vetter@intel.com \
--cc=dave.stevenson@raspberrypi.com \
--cc=dri-devel@lists.freedesktop.org \
--cc=eric@anholt.net \
--cc=hverkuil-cisco@xs4all.nl \
--cc=jason@lakedaemon.net \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=linux-rpi-kernel@lists.infradead.org \
--cc=maarten.lankhorst@linux.intel.com \
--cc=maz@kernel.org \
--cc=mchehab@kernel.org \
--cc=tglx@linutronix.de \
--cc=tzimmermann@suse.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).