From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
To: Bhaumik Bhatt <bbhatt@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org, hemantk@codeaurora.org,
jhugo@codeaurora.org, linux-kernel@vger.kernel.org,
loic.poulain@linaro.org, linux-wireless@vger.kernel.org,
kvalo@codeaurora.org, ath11k@lists.infradead.org
Subject: Re: [PATCH v4 0/6] BHI/BHIe improvements for MHI power purposes
Date: Fri, 25 Jun 2021 10:58:51 +0530 [thread overview]
Message-ID: <20210625052851.GF4974@workstation> (raw)
In-Reply-To: <1620330705-40192-1-git-send-email-bbhatt@codeaurora.org>
On Thu, May 06, 2021 at 12:51:39PM -0700, Bhaumik Bhatt wrote:
> This patch series improves the power up behavior by allowing MHI host driver to
> set BHI and/or BHIe offsets early on in the preparation phase and fail pre-power
> up if offsets are not found or not within a limited MMIO region. This also
> allows MHI host to clean up the offsets in the unprepare after power down phase.
>
> Going forward, controllers will be required to specify a reg_len field which
> will be used to check whether the BHI/BHIe offsets are in range or not.
>
> This series has been tested on X86_64 architecture with the PCI generic driver
> as controller and an SDX55 device.
>
Since there is a chance to send this series for 5.14, I've applied it
now to mhi-next!
Thanks,
Mani
> v4:
> -Added reviewed-by tags
> -Updated range check patch to include BHI/e offsets in the error message
>
> v3:
> -Added reviewed-by tags
> -Updated order of reg_len in mhi_controller structure documentation
>
> v2:
> -Added reviewed-by tags
> -Moved reg_len entry in mhi_controller structure to allow for a packed struct
>
> Bhaumik Bhatt (6):
> bus: mhi: core: Set BHI/BHIe offsets on power up preparation
> bus: mhi: core: Set BHI and BHIe pointers to NULL in clean-up
> bus: mhi: Add MMIO region length to controller structure
> ath11k: set register access length for MHI driver
> bus: mhi: pci_generic: Set register access length for MHI driver
> bus: mhi: core: Add range checks for BHI and BHIe
>
> drivers/bus/mhi/core/init.c | 61 ++++++++++++++++++++++++-----------
> drivers/bus/mhi/core/pm.c | 28 +++-------------
> drivers/bus/mhi/pci_generic.c | 1 +
> drivers/net/wireless/ath/ath11k/mhi.c | 1 +
> include/linux/mhi.h | 2 ++
> 5 files changed, 50 insertions(+), 43 deletions(-)
>
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
>
next prev parent reply other threads:[~2021-06-25 5:29 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-05-06 19:51 [PATCH v4 0/6] BHI/BHIe improvements for MHI power purposes Bhaumik Bhatt
2021-05-06 19:51 ` [PATCH v4 1/6] bus: mhi: core: Set BHI/BHIe offsets on power up preparation Bhaumik Bhatt
2021-05-21 13:36 ` Manivannan Sadhasivam
2021-05-06 19:51 ` [PATCH v4 2/6] bus: mhi: core: Set BHI and BHIe pointers to NULL in clean-up Bhaumik Bhatt
2021-05-21 13:37 ` Manivannan Sadhasivam
2021-05-06 19:51 ` [PATCH v4 3/6] bus: mhi: Add MMIO region length to controller structure Bhaumik Bhatt
2021-05-21 13:38 ` Manivannan Sadhasivam
2021-05-06 19:51 ` [PATCH v4 4/6] ath11k: set register access length for MHI driver Bhaumik Bhatt
2021-05-21 13:51 ` Manivannan Sadhasivam
2021-06-14 16:02 ` Kalle Valo
2021-06-14 17:49 ` Bhaumik Bhatt
2021-06-16 17:38 ` Bhaumik Bhatt
2021-06-18 6:45 ` Manivannan Sadhasivam
2021-06-23 17:29 ` Kalle Valo
2021-06-24 6:09 ` Manivannan Sadhasivam
2021-06-23 17:34 ` Kalle Valo
2021-06-23 21:33 ` Bhaumik Bhatt
2021-05-06 19:51 ` [PATCH v4 5/6] bus: mhi: pci_generic: Set " Bhaumik Bhatt
2021-05-21 13:52 ` Manivannan Sadhasivam
2021-05-06 19:51 ` [PATCH v4 6/6] bus: mhi: core: Add range checks for BHI and BHIe Bhaumik Bhatt
2021-05-07 2:33 ` Hemant Kumar
2021-05-21 13:54 ` Manivannan Sadhasivam
2021-06-25 5:28 ` Manivannan Sadhasivam [this message]
-- strict thread matches above, loose matches on Subject: below --
2021-05-06 19:32 [PATCH v4 0/6] BHI/BHIe improvements for MHI power purposes Bhaumik Bhatt
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210625052851.GF4974@workstation \
--to=manivannan.sadhasivam@linaro.org \
--cc=ath11k@lists.infradead.org \
--cc=bbhatt@codeaurora.org \
--cc=hemantk@codeaurora.org \
--cc=jhugo@codeaurora.org \
--cc=kvalo@codeaurora.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-wireless@vger.kernel.org \
--cc=loic.poulain@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).