From: Martin Kaiser <martin@kaiser.cx>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>,
Phillip Potter <phil@philpotter.co.uk>,
Michael Straube <straube.linux@gmail.com>,
linux-staging@lists.linux.dev, linux-kernel@vger.kernel.org,
Martin Kaiser <martin@kaiser.cx>
Subject: [PATCH 10/10] staging: r8188eu: we only need one struct bb_reg_def for path a
Date: Sat, 12 Feb 2022 17:17:37 +0100 [thread overview]
Message-ID: <20220212161737.381841-11-martin@kaiser.cx> (raw)
In-Reply-To: <20220212161737.381841-1-martin@kaiser.cx>
The r8188eu driver does no longer access rf path b registers via
PHYRegDef.
Change the PHYRegDef array in struct hal_data_8188e to a single
variable that holds the register addresses for rf path a. Remove
the initialisation of path b register addresses.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
---
drivers/staging/r8188eu/hal/rtl8188e_phycfg.c | 58 +++++++------------
drivers/staging/r8188eu/hal/rtl8188e_rf6052.c | 2 +-
.../staging/r8188eu/include/rtl8188e_hal.h | 2 +-
3 files changed, 22 insertions(+), 40 deletions(-)
diff --git a/drivers/staging/r8188eu/hal/rtl8188e_phycfg.c b/drivers/staging/r8188eu/hal/rtl8188e_phycfg.c
index e2e4443b7414..b0e5b9f6a005 100644
--- a/drivers/staging/r8188eu/hal/rtl8188e_phycfg.c
+++ b/drivers/staging/r8188eu/hal/rtl8188e_phycfg.c
@@ -123,7 +123,7 @@ phy_RFSerialRead(
{
u32 retValue = 0;
struct hal_data_8188e *pHalData = &Adapter->haldata;
- struct bb_reg_def *pPhyReg = &pHalData->PHYRegDef[RF_PATH_A];
+ struct bb_reg_def *pPhyReg = &pHalData->PHYRegDef;
u32 NewOffset;
u32 tmplong, tmplong2;
u8 RfPiEnable = 0;
@@ -215,7 +215,7 @@ phy_RFSerialWrite(
{
u32 DataAndAddr = 0;
struct hal_data_8188e *pHalData = &Adapter->haldata;
- struct bb_reg_def *pPhyReg = &pHalData->PHYRegDef[RF_PATH_A];
+ struct bb_reg_def *pPhyReg = &pHalData->PHYRegDef;
u32 NewOffset;
/* 2009/06/17 MH We can not execute IO for power save or other accident mode. */
@@ -358,76 +358,58 @@ phy_InitBBRFRegisterDefinition(
struct hal_data_8188e *pHalData = &Adapter->haldata;
/* RF Interface Sowrtware Control */
- pHalData->PHYRegDef[RF_PATH_A].rfintfs = rFPGA0_XAB_RFInterfaceSW; /* 16 LSBs if read 32-bit from 0x870 */
- pHalData->PHYRegDef[RF_PATH_B].rfintfs = rFPGA0_XAB_RFInterfaceSW; /* 16 MSBs if read 32-bit from 0x870 (16-bit for 0x872) */
+ pHalData->PHYRegDef.rfintfs = rFPGA0_XAB_RFInterfaceSW; /* 16 LSBs if read 32-bit from 0x870 */
/* RF Interface Readback Value */
- pHalData->PHYRegDef[RF_PATH_A].rfintfi = rFPGA0_XAB_RFInterfaceRB; /* 16 LSBs if read 32-bit from 0x8E0 */
- pHalData->PHYRegDef[RF_PATH_B].rfintfi = rFPGA0_XAB_RFInterfaceRB;/* 16 MSBs if read 32-bit from 0x8E0 (16-bit for 0x8E2) */
+ pHalData->PHYRegDef.rfintfi = rFPGA0_XAB_RFInterfaceRB; /* 16 LSBs if read 32-bit from 0x8E0 */
/* RF Interface Output (and Enable) */
- pHalData->PHYRegDef[RF_PATH_A].rfintfo = rFPGA0_XA_RFInterfaceOE; /* 16 LSBs if read 32-bit from 0x860 */
- pHalData->PHYRegDef[RF_PATH_B].rfintfo = rFPGA0_XB_RFInterfaceOE; /* 16 LSBs if read 32-bit from 0x864 */
+ pHalData->PHYRegDef.rfintfo = rFPGA0_XA_RFInterfaceOE; /* 16 LSBs if read 32-bit from 0x860 */
/* RF Interface (Output and) Enable */
- pHalData->PHYRegDef[RF_PATH_A].rfintfe = rFPGA0_XA_RFInterfaceOE; /* 16 MSBs if read 32-bit from 0x860 (16-bit for 0x862) */
- pHalData->PHYRegDef[RF_PATH_B].rfintfe = rFPGA0_XB_RFInterfaceOE; /* 16 MSBs if read 32-bit from 0x864 (16-bit for 0x866) */
+ pHalData->PHYRegDef.rfintfe = rFPGA0_XA_RFInterfaceOE; /* 16 MSBs if read 32-bit from 0x860 (16-bit for 0x862) */
/* Addr of LSSI. Wirte RF register by driver */
- pHalData->PHYRegDef[RF_PATH_A].rf3wireOffset = rFPGA0_XA_LSSIParameter; /* LSSI Parameter */
- pHalData->PHYRegDef[RF_PATH_B].rf3wireOffset = rFPGA0_XB_LSSIParameter;
+ pHalData->PHYRegDef.rf3wireOffset = rFPGA0_XA_LSSIParameter; /* LSSI Parameter */
/* RF parameter */
- pHalData->PHYRegDef[RF_PATH_A].rfLSSI_Select = rFPGA0_XAB_RFParameter; /* BB Band Select */
- pHalData->PHYRegDef[RF_PATH_B].rfLSSI_Select = rFPGA0_XAB_RFParameter;
+ pHalData->PHYRegDef.rfLSSI_Select = rFPGA0_XAB_RFParameter; /* BB Band Select */
/* Tx AGC Gain Stage (same for all path. Should we remove this?) */
- pHalData->PHYRegDef[RF_PATH_A].rfTxGainStage = rFPGA0_TxGainStage; /* Tx gain stage */
- pHalData->PHYRegDef[RF_PATH_B].rfTxGainStage = rFPGA0_TxGainStage; /* Tx gain stage */
+ pHalData->PHYRegDef.rfTxGainStage = rFPGA0_TxGainStage; /* Tx gain stage */
/* Tranceiver A~D HSSI Parameter-1 */
- pHalData->PHYRegDef[RF_PATH_A].rfHSSIPara1 = rFPGA0_XA_HSSIParameter1; /* wire control parameter1 */
- pHalData->PHYRegDef[RF_PATH_B].rfHSSIPara1 = rFPGA0_XB_HSSIParameter1; /* wire control parameter1 */
+ pHalData->PHYRegDef.rfHSSIPara1 = rFPGA0_XA_HSSIParameter1; /* wire control parameter1 */
/* Tranceiver A~D HSSI Parameter-2 */
- pHalData->PHYRegDef[RF_PATH_A].rfHSSIPara2 = rFPGA0_XA_HSSIParameter2; /* wire control parameter2 */
- pHalData->PHYRegDef[RF_PATH_B].rfHSSIPara2 = rFPGA0_XB_HSSIParameter2; /* wire control parameter2 */
+ pHalData->PHYRegDef.rfHSSIPara2 = rFPGA0_XA_HSSIParameter2; /* wire control parameter2 */
/* RF switch Control */
- pHalData->PHYRegDef[RF_PATH_A].rfSwitchControl = rFPGA0_XAB_SwitchControl; /* TR/Ant switch control */
- pHalData->PHYRegDef[RF_PATH_B].rfSwitchControl = rFPGA0_XAB_SwitchControl;
+ pHalData->PHYRegDef.rfSwitchControl = rFPGA0_XAB_SwitchControl; /* TR/Ant switch control */
/* AGC control 1 */
- pHalData->PHYRegDef[RF_PATH_A].rfAGCControl1 = rOFDM0_XAAGCCore1;
- pHalData->PHYRegDef[RF_PATH_B].rfAGCControl1 = rOFDM0_XBAGCCore1;
+ pHalData->PHYRegDef.rfAGCControl1 = rOFDM0_XAAGCCore1;
/* AGC control 2 */
- pHalData->PHYRegDef[RF_PATH_A].rfAGCControl2 = rOFDM0_XAAGCCore2;
- pHalData->PHYRegDef[RF_PATH_B].rfAGCControl2 = rOFDM0_XBAGCCore2;
+ pHalData->PHYRegDef.rfAGCControl2 = rOFDM0_XAAGCCore2;
/* RX AFE control 1 */
- pHalData->PHYRegDef[RF_PATH_A].rfRxIQImbalance = rOFDM0_XARxIQImbalance;
- pHalData->PHYRegDef[RF_PATH_B].rfRxIQImbalance = rOFDM0_XBRxIQImbalance;
+ pHalData->PHYRegDef.rfRxIQImbalance = rOFDM0_XARxIQImbalance;
/* RX AFE control 1 */
- pHalData->PHYRegDef[RF_PATH_A].rfRxAFE = rOFDM0_XARxAFE;
- pHalData->PHYRegDef[RF_PATH_B].rfRxAFE = rOFDM0_XBRxAFE;
+ pHalData->PHYRegDef.rfRxAFE = rOFDM0_XARxAFE;
/* Tx AFE control 1 */
- pHalData->PHYRegDef[RF_PATH_A].rfTxIQImbalance = rOFDM0_XATxIQImbalance;
- pHalData->PHYRegDef[RF_PATH_B].rfTxIQImbalance = rOFDM0_XBTxIQImbalance;
+ pHalData->PHYRegDef.rfTxIQImbalance = rOFDM0_XATxIQImbalance;
/* Tx AFE control 2 */
- pHalData->PHYRegDef[RF_PATH_A].rfTxAFE = rOFDM0_XATxAFE;
- pHalData->PHYRegDef[RF_PATH_B].rfTxAFE = rOFDM0_XBTxAFE;
+ pHalData->PHYRegDef.rfTxAFE = rOFDM0_XATxAFE;
/* Tranceiver LSSI Readback SI mode */
- pHalData->PHYRegDef[RF_PATH_A].rfLSSIReadBack = rFPGA0_XA_LSSIReadBack;
- pHalData->PHYRegDef[RF_PATH_B].rfLSSIReadBack = rFPGA0_XB_LSSIReadBack;
+ pHalData->PHYRegDef.rfLSSIReadBack = rFPGA0_XA_LSSIReadBack;
/* Tranceiver LSSI Readback PI mode */
- pHalData->PHYRegDef[RF_PATH_A].rfLSSIReadBackPi = TransceiverA_HSPI_Readback;
- pHalData->PHYRegDef[RF_PATH_B].rfLSSIReadBackPi = TransceiverB_HSPI_Readback;
+ pHalData->PHYRegDef.rfLSSIReadBackPi = TransceiverA_HSPI_Readback;
}
void storePwrIndexDiffRateOffset(struct adapter *Adapter, u32 RegAddr, u32 BitMask, u32 Data)
diff --git a/drivers/staging/r8188eu/hal/rtl8188e_rf6052.c b/drivers/staging/r8188eu/hal/rtl8188e_rf6052.c
index 4a7a877e4017..d043b7bc4142 100644
--- a/drivers/staging/r8188eu/hal/rtl8188e_rf6052.c
+++ b/drivers/staging/r8188eu/hal/rtl8188e_rf6052.c
@@ -375,7 +375,7 @@ static int phy_RF6052_Config_ParaFile(struct adapter *Adapter)
/* Initialize RF */
- pPhyReg = &pHalData->PHYRegDef[0];
+ pPhyReg = &pHalData->PHYRegDef;
/*----Store original RFENV control type----*/
u4RegValue = rtl8188e_PHY_QueryBBReg(Adapter, pPhyReg->rfintfs, bRFSI_RFENV);
diff --git a/drivers/staging/r8188eu/include/rtl8188e_hal.h b/drivers/staging/r8188eu/include/rtl8188e_hal.h
index 5b27bae97e91..44321a53a345 100644
--- a/drivers/staging/r8188eu/include/rtl8188e_hal.h
+++ b/drivers/staging/r8188eu/include/rtl8188e_hal.h
@@ -141,7 +141,7 @@ struct hal_data_8188e {
u32 AcParam_BE; /* Original parameter for BE, use for EDCA turbo. */
- struct bb_reg_def PHYRegDef[2]; /* Radio A/B */
+ struct bb_reg_def PHYRegDef;
u32 RfRegChnlVal;
--
2.30.2
prev parent reply other threads:[~2022-02-12 16:19 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-02-12 16:17 [PATCH 00/10] remove rf register access for path b Martin Kaiser
2022-02-12 16:17 ` [PATCH 01/10] staging: r8188eu: set path a explicitly Martin Kaiser
2022-02-12 16:17 ` [PATCH 02/10] staging: r8188eu: write only path a registers in rtw_dbg_port Martin Kaiser
2022-02-12 16:17 ` [PATCH 03/10] staging: r8188eu: remove path parameter from rtl8188e_PHY_SetRFReg Martin Kaiser
2022-02-12 16:17 ` [PATCH 04/10] staging: r8188eu: remove path parameter from phy_RFSerialWrite Martin Kaiser
2022-02-12 16:17 ` [PATCH 05/10] staging: r8188eu: clarify that bb_reg_dump uses only path a Martin Kaiser
2022-02-12 16:17 ` [PATCH 06/10] staging: r8188eu: limit rtw_wx_read_rf to " Martin Kaiser
2022-02-12 16:17 ` [PATCH 07/10] staging: r8188eu: limit rtw_dbg_port " Martin Kaiser
2022-02-12 16:17 ` [PATCH 08/10] staging: r8188eu: remove path parameter from rtl8188e_PHY_QueryRFReg Martin Kaiser
2022-02-12 16:17 ` [PATCH 09/10] staging: r8188eu: remove path parameter from phy_RFSerialRead Martin Kaiser
2022-02-12 16:17 ` Martin Kaiser [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220212161737.381841-11-martin@kaiser.cx \
--to=martin@kaiser.cx \
--cc=Larry.Finger@lwfinger.net \
--cc=gregkh@linuxfoundation.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-staging@lists.linux.dev \
--cc=phil@philpotter.co.uk \
--cc=straube.linux@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).