From: Michael Walle <michael@walle.cc>
To: Kavyasree Kotagiri <kavyasree.kotagiri@microchip.com>,
Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Arnd Bergmann <arnd@arndb.de>, Olof Johansson <olof@lixom.net>,
soc@kernel.org, linux-arm-kernel@lists.infradead.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>,
Alexandre Belloni <alexandre.belloni@bootlin.com>,
Claudiu Beznea <claudiu.beznea@microchip.com>,
Tudor.Ambarus@microchip.com,
Horatiu Vultur <horatiu.vultur@microchip.com>,
Michael Walle <michael@walle.cc>
Subject: [PATCH v4 02/13] ARM: dts: lan966x: add sgpio node
Date: Tue, 3 May 2022 00:41:16 +0200 [thread overview]
Message-ID: <20220502224127.2604333-3-michael@walle.cc> (raw)
In-Reply-To: <20220502224127.2604333-1-michael@walle.cc>
Add the device tree node for the SGPIO IP block reused from the
SparX-5. Keep the node disabled by default.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
---
arch/arm/boot/dts/lan966x.dtsi | 26 ++++++++++++++++++++++++++
1 file changed, 26 insertions(+)
diff --git a/arch/arm/boot/dts/lan966x.dtsi b/arch/arm/boot/dts/lan966x.dtsi
index a99ffb4cfb8a..4c7beebbd1ef 100644
--- a/arch/arm/boot/dts/lan966x.dtsi
+++ b/arch/arm/boot/dts/lan966x.dtsi
@@ -223,6 +223,32 @@ gpio: pinctrl@e2004064 {
#interrupt-cells = <2>;
};
+ sgpio: gpio@e2004190 {
+ compatible = "microchip,sparx5-sgpio";
+ reg = <0xe2004190 0x118>;
+ clocks = <&sys_clk>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ sgpio_in: gpio@0 {
+ compatible = "microchip,sparx5-sgpio-bank";
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ };
+
+ sgpio_out: gpio@1 {
+ compatible = "microchip,sparx5-sgpio-bank";
+ reg = <1>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ };
+ };
+
gic: interrupt-controller@e8c11000 {
compatible = "arm,gic-400", "arm,cortex-a7-gic";
#interrupt-cells = <3>;
--
2.30.2
next prev parent reply other threads:[~2022-05-02 22:41 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-05-02 22:41 [PATCH v4 00/13] ARM: dts: lan966x: dtsi improvements and KSwitch D10 support Michael Walle
2022-05-02 22:41 ` [PATCH v4 01/13] ARM: dts: lan966x: swap dma channels for crypto node Michael Walle
2022-05-02 22:41 ` Michael Walle [this message]
2022-05-02 22:41 ` [PATCH v4 03/13] ARM: dts: lan966x: add missing uart DMA channel Michael Walle
2022-05-02 22:41 ` [PATCH v4 04/13] ARM: dts: lan966x: add all flexcom usart nodes Michael Walle
2022-05-02 22:41 ` [PATCH v4 05/13] ARM: dts: lan966x: add flexcom SPI nodes Michael Walle
2022-05-02 22:41 ` [PATCH v4 06/13] ARM: dts: lan966x: add flexcom I2C nodes Michael Walle
2022-05-02 22:41 ` [PATCH v4 07/13] ARM: dts: lan966x: add basic Kontron KSwitch D10 support Michael Walle
2022-05-02 22:41 ` [PATCH v4 08/13] ARM: dts: lan966x: add hwmon node Michael Walle
2022-05-09 6:25 ` Claudiu.Beznea
2022-05-02 22:41 ` [PATCH v4 09/13] ARM: dts: lan966x: add MIIM nodes Michael Walle
2022-05-09 6:26 ` Claudiu.Beznea
2022-05-02 22:41 ` [PATCH v4 10/13] ARM: dts: lan966x: add reset switch reset node Michael Walle
2022-05-09 6:26 ` Claudiu.Beznea
2022-05-02 22:41 ` [PATCH v4 11/13] ARM: dts: lan966x: add serdes node Michael Walle
2022-05-09 6:26 ` Claudiu.Beznea
2022-05-02 22:41 ` [PATCH v4 12/13] ARM: dts: lan966x: add switch node Michael Walle
2022-05-09 6:27 ` Claudiu.Beznea
2022-05-02 22:41 ` [PATCH v4 13/13] ARM: dts: kswitch-d10: enable networking Michael Walle
2022-05-09 6:27 ` Claudiu.Beznea
2022-05-04 10:16 ` [PATCH v4 00/13] ARM: dts: lan966x: dtsi improvements and KSwitch D10 support Horatiu Vultur
2022-05-11 9:07 ` Michael Walle
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220502224127.2604333-3-michael@walle.cc \
--to=michael@walle.cc \
--cc=Tudor.Ambarus@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=arnd@arndb.de \
--cc=claudiu.beznea@microchip.com \
--cc=devicetree@vger.kernel.org \
--cc=horatiu.vultur@microchip.com \
--cc=kavyasree.kotagiri@microchip.com \
--cc=krzysztof.kozlowski@canonical.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nicolas.ferre@microchip.com \
--cc=olof@lixom.net \
--cc=robh+dt@kernel.org \
--cc=soc@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).