From: William Zhang <william.zhang@broadcom.com>
To: Linux ARM List <linux-arm-kernel@lists.infradead.org>,
Broadcom Kernel List <bcm-kernel-feedback-list@broadcom.com>
Cc: kursad.oney@broadcom.com, florian.fainelli@broadcom.com,
joel.peshkin@broadcom.com, tomer.yacoby@broadcom.com,
samyon.furman@broadcom.com, philippe.reynes@softathome.com,
anand.gore@broadcom.com, dan.beygelman@broadcom.com,
William Zhang <william.zhang@broadcom.com>,
Florian Fainelli <f.fainelli@gmail.com>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Nicolas Saenz Julienne <nsaenz@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Stefan Wahren <stefan.wahren@i2se.com>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH 3/5] arm64: dts: add dts files for bcmbca soc 63158
Date: Sat, 14 May 2022 16:27:58 -0700 [thread overview]
Message-ID: <20220514232800.24653-4-william.zhang@broadcom.com> (raw)
In-Reply-To: <20220514232800.24653-1-william.zhang@broadcom.com>
[-- Attachment #1: Type: text/plain, Size: 5413 bytes --]
Add dts for ARMv8 based broadband SoC BCM63158. bcm63158.dtsi is the
SoC description dts header and bcm963158.dts is a simple dts file for
Broadcom BCM963158 Reference board that only enable the UART port.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
---
arch/arm64/boot/dts/broadcom/Makefile | 1 +
arch/arm64/boot/dts/broadcom/bcmbca/Makefile | 2 +
.../boot/dts/broadcom/bcmbca/bcm63158.dtsi | 128 ++++++++++++++++++
.../boot/dts/broadcom/bcmbca/bcm963158.dts | 30 ++++
4 files changed, 161 insertions(+)
create mode 100644 arch/arm64/boot/dts/broadcom/bcmbca/Makefile
create mode 100644 arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi
create mode 100644 arch/arm64/boot/dts/broadcom/bcmbca/bcm963158.dts
diff --git a/arch/arm64/boot/dts/broadcom/Makefile b/arch/arm64/boot/dts/broadcom/Makefile
index 5082fcd1fea5..e8584d3b698f 100644
--- a/arch/arm64/boot/dts/broadcom/Makefile
+++ b/arch/arm64/boot/dts/broadcom/Makefile
@@ -9,5 +9,6 @@ dtb-$(CONFIG_ARCH_BCM2835) += bcm2711-rpi-400.dtb \
bcm2837-rpi-zero-2-w.dtb
subdir-y += bcm4908
+subdir-y += bcmbca
subdir-y += northstar2
subdir-y += stingray
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/Makefile b/arch/arm64/boot/dts/broadcom/bcmbca/Makefile
new file mode 100644
index 000000000000..d5f89245336c
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_BCMBCA) += bcm963158.dtb
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi b/arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi
new file mode 100644
index 000000000000..cfa235d99a32
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ compatible = "brcm,bcm63158", "brcm,bcmbca";
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ B53_0: cpu@0 {
+ compatible = "brcm,brahma-b53";
+ device_type = "cpu";
+ reg = <0x0 0x0>;
+ next-level-cache = <&L2_0>;
+ enable-method = "psci";
+ };
+
+ B53_1: cpu@1 {
+ compatible = "brcm,brahma-b53";
+ device_type = "cpu";
+ reg = <0x0 0x1>;
+ next-level-cache = <&L2_0>;
+ enable-method = "psci";
+ };
+
+ B53_2: cpu@2 {
+ compatible = "brcm,brahma-b53";
+ device_type = "cpu";
+ reg = <0x0 0x2>;
+ next-level-cache = <&L2_0>;
+ enable-method = "psci";
+ };
+
+ B53_3: cpu@3 {
+ compatible = "brcm,brahma-b53";
+ device_type = "cpu";
+ reg = <0x0 0x3>;
+ next-level-cache = <&L2_0>;
+ enable-method = "psci";
+ };
+
+ L2_0: l2-cache0 {
+ compatible = "cache";
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ pmu: pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&B53_0>, <&B53_1>,
+ <&B53_2>, <&B53_3>;
+ };
+
+ clocks: clocks {
+ periph_clk: periph-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <200000000>;
+ };
+ uart_clk: uart-clk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clocks = <&periph_clk>;
+ clock-div = <4>;
+ clock-mult = <1>;
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ cpu_off = <1>;
+ cpu_on = <2>;
+ };
+
+ axi@81000000 {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0x81000000 0x0 0x4000>;
+
+ gic: interrupt-controller@1000 {
+ compatible = "arm,gic-400";
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ interrupt-controller;
+ reg = <0x0 0x1000 0x0 0x1000>,
+ <0x0 0x2000 0x0 0x2000>;
+ };
+ };
+
+ bus@ff800000 {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xff800000 0x0 0x800000>;
+
+ uart0: serial@12000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0x12000 0x0 0x1000>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&uart_clk>, <&uart_clk>;
+ clock-names = "uartclk", "apb_pclk";
+ status = "disabled";
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm963158.dts b/arch/arm64/boot/dts/broadcom/bcmbca/bcm963158.dts
new file mode 100644
index 000000000000..eba07e0b1ca6
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm963158.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm63158.dtsi"
+
+/ {
+ model = "Broadcom BCM963158 Reference Board";
+ compatible = "brcm,bcm963158", "brcm,bcm63158", "brcm,bcmbca";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x08000000>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
--
2.17.1
[-- Attachment #2: S/MIME Cryptographic Signature --]
[-- Type: application/pkcs7-signature, Size: 4212 bytes --]
next prev parent reply other threads:[~2022-05-14 23:29 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-05-14 23:27 [PATCH 0/5] arm64: bcmbca: add bcm63158 soc support William Zhang
2022-05-14 23:27 ` [PATCH 1/5] dt-bindings: arm64: add BCM63158 soc to binding document William Zhang
2022-05-16 16:06 ` Rob Herring
2022-05-16 17:51 ` William Zhang
2022-05-17 14:23 ` Rob Herring
2022-05-18 20:08 ` Florian Fainelli
2022-05-14 23:27 ` [PATCH 2/5] arm64: bcmbca: add arch bcmbca machine entry William Zhang
2022-05-18 20:05 ` Florian Fainelli
2022-05-14 23:27 ` William Zhang [this message]
2022-05-18 20:05 ` [PATCH 3/5] arm64: dts: add dts files for bcmbca soc 63158 Florian Fainelli
2022-05-14 23:27 ` [PATCH 4/5] MAINTAINERS: add bcm63158 to bcmbca arch entry William Zhang
2022-05-18 20:08 ` Florian Fainelli
2022-05-14 23:28 ` [PATCH 5/5] arm64: defconfig: enable bcmbca soc support William Zhang
2022-05-18 20:07 ` Florian Fainelli
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220514232800.24653-4-william.zhang@broadcom.com \
--to=william.zhang@broadcom.com \
--cc=anand.gore@broadcom.com \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=dan.beygelman@broadcom.com \
--cc=devicetree@vger.kernel.org \
--cc=f.fainelli@gmail.com \
--cc=florian.fainelli@broadcom.com \
--cc=joel.peshkin@broadcom.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=kursad.oney@broadcom.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nsaenz@kernel.org \
--cc=philippe.reynes@softathome.com \
--cc=robh+dt@kernel.org \
--cc=samyon.furman@broadcom.com \
--cc=stefan.wahren@i2se.com \
--cc=tomer.yacoby@broadcom.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).