From: Danielle Ratson <danieller@nvidia.com>
To: <netdev@vger.kernel.org>
Cc: <davem@davemloft.net>, <edumazet@google.com>, <kuba@kernel.org>,
<pabeni@redhat.com>, <corbet@lwn.net>, <linux@armlinux.org.uk>,
<sdf@google.com>, <kory.maincent@bootlin.com>,
<maxime.chevallier@bootlin.com>, <vladimir.oltean@nxp.com>,
<przemyslaw.kitszel@intel.com>, <ahmed.zaki@intel.com>,
<richardcochran@gmail.com>, <shayagr@amazon.com>,
<paul.greenwalt@intel.com>, <jiri@resnulli.us>,
<linux-doc@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<mlxsw@nvidia.com>, <petrm@nvidia.com>, <idosch@nvidia.com>,
<danieller@nvidia.com>
Subject: [PATCH net-next v4 10/10] ethtool: Veto some operations during firmware flashing process
Date: Thu, 18 Apr 2024 13:34:55 +0300 [thread overview]
Message-ID: <20240418103455.3297870-11-danieller@nvidia.com> (raw)
In-Reply-To: <20240418103455.3297870-1-danieller@nvidia.com>
Some operations cannot be performed during the firmware flashing process.
For example:
- Port must be down during the whole flashing process to avoid packet loss
while committing reset for example.
- Writing to EEPROM interrupts the flashing process, so operations like
ethtool dump, module reset, get and set power mode should be vetoed.
- Split port firmware flashing should be vetoed.
- Flashing firmware on a device which is already in a flashing process
should be forbidden.
Use the 'module_fw_flashing_in_progress' flag introduced in a previous
patch to veto those operations and prevent interruptions while preforming
module firmware flash.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
---
net/ethtool/eeprom.c | 6 ++++++
net/ethtool/ioctl.c | 12 ++++++++++++
net/ethtool/module.c | 29 +++++++++++++++++++++++++++++
net/ethtool/netlink.c | 30 +++++++++++++++++++++++++++++-
4 files changed, 76 insertions(+), 1 deletion(-)
diff --git a/net/ethtool/eeprom.c b/net/ethtool/eeprom.c
index 6209c3a9c8f7..f36811b3ecf1 100644
--- a/net/ethtool/eeprom.c
+++ b/net/ethtool/eeprom.c
@@ -91,6 +91,12 @@ static int get_module_eeprom_by_page(struct net_device *dev,
{
const struct ethtool_ops *ops = dev->ethtool_ops;
+ if (dev->module_fw_flash_in_progress) {
+ NL_SET_ERR_MSG(extack,
+ "Module firmware flashing is in progress");
+ return -EBUSY;
+ }
+
if (dev->sfp_bus)
return sfp_get_module_eeprom_by_page(dev->sfp_bus, page_data, extack);
diff --git a/net/ethtool/ioctl.c b/net/ethtool/ioctl.c
index 5a55270aa86e..02b23805d2be 100644
--- a/net/ethtool/ioctl.c
+++ b/net/ethtool/ioctl.c
@@ -658,6 +658,9 @@ static int ethtool_get_settings(struct net_device *dev, void __user *useraddr)
if (!dev->ethtool_ops->get_link_ksettings)
return -EOPNOTSUPP;
+ if (dev->module_fw_flash_in_progress)
+ return -EBUSY;
+
memset(&link_ksettings, 0, sizeof(link_ksettings));
err = dev->ethtool_ops->get_link_ksettings(dev, &link_ksettings);
if (err < 0)
@@ -1449,6 +1452,9 @@ static int ethtool_reset(struct net_device *dev, char __user *useraddr)
if (!dev->ethtool_ops->reset)
return -EOPNOTSUPP;
+ if (dev->module_fw_flash_in_progress)
+ return -EBUSY;
+
if (copy_from_user(&reset, useraddr, sizeof(reset)))
return -EFAULT;
@@ -2462,6 +2468,9 @@ int ethtool_get_module_info_call(struct net_device *dev,
const struct ethtool_ops *ops = dev->ethtool_ops;
struct phy_device *phydev = dev->phydev;
+ if (dev->module_fw_flash_in_progress)
+ return -EBUSY;
+
if (dev->sfp_bus)
return sfp_get_module_info(dev->sfp_bus, modinfo);
@@ -2499,6 +2508,9 @@ int ethtool_get_module_eeprom_call(struct net_device *dev,
const struct ethtool_ops *ops = dev->ethtool_ops;
struct phy_device *phydev = dev->phydev;
+ if (dev->module_fw_flash_in_progress)
+ return -EBUSY;
+
if (dev->sfp_bus)
return sfp_get_module_eeprom(dev->sfp_bus, ee, data);
diff --git a/net/ethtool/module.c b/net/ethtool/module.c
index 836c198d2cc4..239e7974f952 100644
--- a/net/ethtool/module.c
+++ b/net/ethtool/module.c
@@ -3,6 +3,7 @@
#include <linux/ethtool.h>
#include <linux/firmware.h>
#include <linux/sfp.h>
+#include <net/devlink.h>
#include "netlink.h"
#include "common.h"
@@ -36,6 +37,12 @@ static int module_get_power_mode(struct net_device *dev,
if (!ops->get_module_power_mode)
return 0;
+ if (dev->module_fw_flash_in_progress) {
+ NL_SET_ERR_MSG(extack,
+ "Module firmware flashing is in progress");
+ return -EBUSY;
+ }
+
return ops->get_module_power_mode(dev, &data->power, extack);
}
@@ -112,6 +119,12 @@ ethnl_set_module_validate(struct ethnl_req_info *req_info,
if (!tb[ETHTOOL_A_MODULE_POWER_MODE_POLICY])
return 0;
+ if (req_info->dev->module_fw_flash_in_progress) {
+ NL_SET_ERR_MSG(info->extack,
+ "Module firmware flashing is in progress");
+ return -EBUSY;
+ }
+
if (!ops->get_module_power_mode || !ops->set_module_power_mode) {
NL_SET_ERR_MSG_ATTR(info->extack,
tb[ETHTOOL_A_MODULE_POWER_MODE_POLICY],
@@ -219,6 +232,7 @@ static int module_flash_fw_work_init(struct ethtool_module_fw_flash *module_fw,
static int __module_flash_fw_schedule(struct net_device *dev,
struct netlink_ext_ack *extack)
{
+ struct devlink_port *devlink_port = dev->devlink_port;
const struct ethtool_ops *ops = dev->ethtool_ops;
if (!ops->set_module_eeprom_by_page ||
@@ -234,6 +248,21 @@ static int __module_flash_fw_schedule(struct net_device *dev,
return -EOPNOTSUPP;
}
+ if (dev->module_fw_flash_in_progress) {
+ NL_SET_ERR_MSG(extack, "Module firmware flashing already in progress");
+ return -EBUSY;
+ }
+
+ if (dev->flags & IFF_UP) {
+ NL_SET_ERR_MSG(extack, "Netdevice is up, so flashing is not permitted");
+ return -EBUSY;
+ }
+
+ if (devlink_port && devlink_port->attrs.split) {
+ NL_SET_ERR_MSG(extack, "Can't perform firmware flashing on a split port");
+ return -EOPNOTSUPP;
+ }
+
return 0;
}
diff --git a/net/ethtool/netlink.c b/net/ethtool/netlink.c
index 1a4f6bd1ec7f..90e5b5312aa2 100644
--- a/net/ethtool/netlink.c
+++ b/net/ethtool/netlink.c
@@ -1194,6 +1194,29 @@ static struct genl_family ethtool_genl_family __ro_after_init = {
.n_mcgrps = ARRAY_SIZE(ethtool_nl_mcgrps),
};
+static int module_netdev_pre_up_event(struct notifier_block *this,
+ unsigned long event, void *ptr)
+{
+ struct net_device *dev = netdev_notifier_info_to_dev(ptr);
+ struct netdev_notifier_info *info = ptr;
+ struct netlink_ext_ack *extack;
+
+ extack = netdev_notifier_info_to_extack(info);
+
+ if (event == NETDEV_PRE_UP) {
+ if (dev->module_fw_flash_in_progress) {
+ NL_SET_ERR_MSG(extack, "Can't set port up while flashing module firmware");
+ return NOTIFY_BAD;
+ }
+ }
+
+ return NOTIFY_DONE;
+}
+
+static struct notifier_block ethtool_module_netdev_pre_up_notifier = {
+ .notifier_call = module_netdev_pre_up_event,
+};
+
/* module setup */
static int __init ethnl_init(void)
@@ -1206,7 +1229,12 @@ static int __init ethnl_init(void)
ethnl_ok = true;
ret = register_netdevice_notifier(ðnl_netdev_notifier);
- WARN(ret < 0, "ethtool: net device notifier registration failed");
+ if (WARN(ret < 0, "ethtool: net device notifier registration failed"))
+ return ret;
+
+ ret = register_netdevice_notifier(ðtool_module_netdev_pre_up_notifier);
+ WARN(ret < 0, "ethtool: net device port up notifier registration failed");
+
return ret;
}
--
2.43.0
next prev parent reply other threads:[~2024-04-18 10:36 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-04-18 10:34 [PATCH net-next v4 00/10] Add ability to flash modules' firmware Danielle Ratson
2024-04-18 10:34 ` [PATCH net-next v4 01/10] ethtool: Add ethtool operation to write to a transceiver module EEPROM Danielle Ratson
2024-04-18 10:34 ` [PATCH net-next v4 02/10] mlxsw: Implement " Danielle Ratson
2024-04-18 10:34 ` [PATCH net-next v4 03/10] ethtool: Add an interface for flashing transceiver modules' firmware Danielle Ratson
2024-04-19 2:07 ` Jakub Kicinski
2024-04-18 10:34 ` [PATCH net-next v4 04/10] ethtool: Add flashing transceiver modules' firmware notifications ability Danielle Ratson
2024-04-18 10:34 ` [PATCH net-next v4 05/10] include: netdevice: Add module firmware flashing in progress flag to net_device Danielle Ratson
2024-04-18 10:34 ` [PATCH net-next v4 06/10] net: sfp: Add more extended compliance codes Danielle Ratson
2024-04-18 10:34 ` [PATCH net-next v4 07/10] ethtool: cmis_cdb: Add a layer for supporting CDB commands Danielle Ratson
2024-04-19 1:59 ` Jakub Kicinski
2024-04-18 10:34 ` [PATCH net-next v4 08/10] ethtool: cmis_fw_update: add a layer for supporting firmware update using CDB Danielle Ratson
2024-04-18 10:34 ` [PATCH net-next v4 09/10] ethtool: Add ability to flash transceiver modules' firmware Danielle Ratson
2024-04-18 10:34 ` Danielle Ratson [this message]
2024-04-19 2:10 ` [PATCH net-next v4 00/10] Add ability to flash " Jakub Kicinski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240418103455.3297870-11-danieller@nvidia.com \
--to=danieller@nvidia.com \
--cc=ahmed.zaki@intel.com \
--cc=corbet@lwn.net \
--cc=davem@davemloft.net \
--cc=edumazet@google.com \
--cc=idosch@nvidia.com \
--cc=jiri@resnulli.us \
--cc=kory.maincent@bootlin.com \
--cc=kuba@kernel.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=maxime.chevallier@bootlin.com \
--cc=mlxsw@nvidia.com \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=paul.greenwalt@intel.com \
--cc=petrm@nvidia.com \
--cc=przemyslaw.kitszel@intel.com \
--cc=richardcochran@gmail.com \
--cc=sdf@google.com \
--cc=shayagr@amazon.com \
--cc=vladimir.oltean@nxp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).