From: "Paul E. Erkkila" <pee@erkkila.org>
To: linux-kernel@vger.kernel.org
Subject: oops in bk pull (oct 03)
Date: Fri, 04 Oct 2002 20:14:26 +0000 [thread overview]
Message-ID: <3D9DF6A2.9030101@erkkila.org> (raw)
[-- Attachment #1: Type: text/plain, Size: 111 bytes --]
Oops in drivers/pci/probe.c
Oops (copied), ksymoops, and lspci -vv attached
Dual p3, MSI motherboard
-pee
[-- Attachment #2: koops.out --]
[-- Type: text/plain, Size: 8987 bytes --]
ksymoops 2.4.5 on i686 2.4.19-crypto-r7. Options used
-v ./vmlinux (specified)
-K (specified)
-L (specified)
-o /lib/modules/2.4.19-crypto-r7/ (default)
-m System.map (specified)
No modules in ksyms, skipping objects
Unable to handle kernel paging request at virtual address f8000008
c01c9d10
*pde = 00000000
Oops: 0002
CPU: 0
EIP: 0060:[<c01c9d10>] Not tainted
Using defaults from ksymoops -t elf32-i386 -a i386
EFLAGS: 00010202
eax: f8000008 ebx: 00000010 ecx: 00000000 edx: f8000008
esi: c1523c00 edi: c1523d38 ebp: 00000001 esp: dffcdb60
ds: 0068 es: 0068 ss: 0068
Stack: c01c9e91 f8000008 fffffff0 00000010 dffcdb78 c1523ef8 f8000008 00000008
d0000008 c1523c00 c1523f48 00000000 00000000 c01ca2a6 c1523c00 00000006
00000030 dffcdbac 00000000 00000600 c1523c00 dffcdc20 c03a1351 c1523c00
[<c01c9e91>] pci_read_bases+0x161/0x340
[<c01ca2a6>] pci_setup_device+0x1b6/0x3d0
[<c0105109>] init+0x79/0x200
[<c0105090>] init+0x0/0x200
[<c01073e5>] kernel_thread_helper+0x5/0x10
Code: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 48 c3 8d b4
>>EIP; c01c9d10 <pci_size+0/20> <=====
>>eax; f8000008 <END_OF_CODE+37aa9717/????>
>>edx; f8000008 <END_OF_CODE+37aa9717/????>
>>esi; c1523c00 <END_OF_CODE+fcd30f/????>
>>edi; c1523d38 <END_OF_CODE+fcd447/????>
>>esp; dffcdb60 <END_OF_CODE+1fa7726f/????>
Code; c01c9d10 <pci_size+0/20> <=====
00000000 <_EIP>: <=====
Code; c01c9d20 <pci_size+10/20>
10: 48 dec %eax
Code; c01c9d21 <pci_size+11/20>
11: c3 ret
Code; c01c9d22 <pci_size+12/20>
12: 8d b4 00 00 00 00 00 lea 0x0(%eax,%eax,1),%esi
<0>Kernel panic: Attempted to kill init!
===lspci -vv ===
00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2,x4
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: da000000-dcffffff
Prefetchable memory behind bridge: d8000000-d9ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586B PIPC Bus Master IDE (rev 10) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at c000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 10) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at c400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.3 USB Controller: VIA Technologies, Inc. USB (rev 10) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at c800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 20)
Subsystem: VIA Technologies, Inc. VT82C686 AC97 Audio Controller
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 15
Region 0: I/O ports at cc00 [size=256]
Region 1: I/O ports at d000 [size=4]
Region 2: I/O ports at d400 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 RAID bus controller: Promise Technology, Inc. 20265 (rev 02)
Subsystem: Promise Technology, Inc. Ultra100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 15
Region 0: I/O ports at d800 [size=8]
Region 1: I/O ports at dc00 [size=4]
Region 2: I/O ports at e000 [size=8]
Region 3: I/O ports at e400 [size=4]
Region 4: I/O ports at e800 [size=64]
Region 5: Memory at de000000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [58] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:12.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30)
Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 2500ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at ec00 [size=128]
Region 1: Memory at de020000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 82) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G450 Dual Head
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at da000000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at db000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2,x4
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1
next reply other threads:[~2002-10-04 20:10 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-10-04 20:14 Paul E. Erkkila [this message]
2002-10-04 21:58 ` oops in bk pull (oct 03) Linus Torvalds
2002-10-05 0:03 ` Paul E. Erkkila
2002-10-05 0:33 ` Alexander Viro
2002-10-05 0:40 ` Linus Torvalds
2002-10-05 0:51 ` Alexander Viro
2002-10-05 1:02 ` Linus Torvalds
2002-10-05 1:13 ` David S. Miller
2002-10-05 1:27 ` Alexander Viro
2002-10-05 1:41 ` Linus Torvalds
2002-10-05 2:00 ` David S. Miller
2002-10-05 2:22 ` Linus Torvalds
2002-10-05 2:22 ` David S. Miller
2002-10-05 2:00 ` Linus Torvalds
2002-10-05 3:20 ` Alexander Viro
2002-10-05 3:26 ` Linus Torvalds
2002-10-05 9:35 ` Ivan Kokshaysky
2002-10-05 1:14 ` Alexander Viro
2002-10-05 0:44 ` Alexander Viro
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3D9DF6A2.9030101@erkkila.org \
--to=pee@erkkila.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).