LIFO batch:0 Normal zone: 126688 pages, LIFO batch:31 HighMem zone: 0 pages, LIFO batch:0 DMI present. ACPI: RSDP (v002 IBM ) @ 0x000f6c00 ACPI: XSDT (v001 IBM TP-1Y 0x00001240 LTP 0x00000000) @ 0x1fee6ff2 ACPI: FADT (v003 IBM TP-1Y 0x00001240 IBM 0x00000001) @ 0x1fee7100 ACPI: SSDT (v001 IBM TP-1Y 0x00001240 MSFT 0x0100000e) @ 0x1fee72b4 ACPI: ECDT (v001 IBM TP-1Y 0x00001240 IBM 0x00000001) @ 0x1fef4def ACPI: TCPA (v001 IBM TP-1Y 0x00001240 PTL 0x00000001) @ 0x1fef4e41 ACPI: MADT (v001 IBM TP-1Y 0x00001240 IBM 0x00000001) @ 0x1fef4e73 ACPI: MCFG (v001 IBM TP-1Y 0x00001240 IBM 0x00000001) @ 0x1fef4ecd ACPI: BOOT (v001 IBM TP-1Y 0x00001240 LTP 0x00000001) @ 0x1fef4fd8 ACPI: DSDT (v001 IBM TP-1Y 0x00001240 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 6:13 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000) Built 1 zonelists Kernel command line: root=/dev/sda5 ro mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Initializing CPU#0 PID hash table entries: 2048 (order: 11, 32768 bytes) Detected 1862.258 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 515644k/523136k available (1494k kernel code, 7012k reserved, 605k data, 152k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 3729.50 BogoMIPS (lpj=7459011) Mount-cache hash table entries: 512 CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000 CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000180 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. mtrr: v2.0 (20020519) CPU: Intel(R) Pentium(R) M processor 1.86GHz stepping 08 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfd8f7, last bus=7 PCI: Using MMCONFIG ACPI: Subsystem revision 20050902 ACPI: Found ECDT ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO PCI quirk: region 1180-11bf claimed by ICH6 GPIO PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2 Boot video device is 0000:01:00.0 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: Embedded Controller [EC] (gpe 28) ACPI: Power Resource [PUBS] (on) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 13 devices PnPBIOS: Disabled by ACPI PNP SCSI subsystem initialized PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Bridge: 0000:00:01.0 IO window: 2000-2fff MEM window: a8100000-a81fffff PREFETCH window: c0000000-c7ffffff PCI: Bridge: 0000:00:1c.0 IO window: disabled. MEM window: a8200000-a82fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.2 IO window: 3000-3fff MEM window: a8300000-a83fffff PREFETCH window: c8000000-c80fffff PCI: Bus 5, cardbus bridge: 0000:04:00.0 IO window: 00004000-000040ff IO window: 00004400-000044ff PREFETCH window: d0000000-d1ffffff MEM window: aa000000-abffffff PCI: Bridge: 0000:00:1e.0 IO window: 4000-7fff MEM window: a8400000-b7ffffff PREFETCH window: d0000000-d7ffffff ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:01.0 to 64 ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 20 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 22 (level, low) -> IRQ 185 PCI: Setting latency timer of device 0000:00:1c.2 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 169 Simple Boot Flag at 0x35 set to 0x1 Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:01.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[pcie00] Allocate Port Service[pcie03] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 20 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[pcie00] Allocate Port Service[pcie02] Allocate Port Service[pcie03] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 22 (level, low) -> IRQ 185 PCI: Setting latency timer of device 0000:00:1c.2 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[pcie00] Allocate Port Service[pcie02] Allocate Port Service[pcie03] ibm_acpi: IBM ThinkPad ACPI Extras v0.12a ibm_acpi: http://ibm-acpi.sf.net/ ibm_acpi: dock device not present isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled pnp: Device 00:08 activated. 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ide0: I/O resource 0x1F0-0x1F7 not free. ide0: ports already in use, skipping probe Probing IDE interface ide1... hdc: MATSHITADVD-RAM UJ-822S, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 libata version 1.20 loaded. ata_piix 0000:00:1f.2: version 1.05 ata: 0x170 IDE port busy PCI: Setting latency timer of device 0000:00:1f.2 to 64 ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x18C0 irq 14 ata1: dev 0 cfg 49:0f00 82:746b 83:5be9 84:6003 85:f469 86:1849 87:6003 88:203f ata1: dev 0 ATA-6, max UDMA/100, 156301488 sectors: LBA ata1(0): applying bridge limits ata1: dev 0 configured for UDMA/100 scsi0 : ata_piix Vendor: ATA Model: HTS541080G9AT00 Rev: MB4I Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) SCSI device sda: drive cache: write back SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 > sd 0:0:0:0: Attached scsi disk sda mice: PS/2 mouse device common for all mice NET: Registered protocol family 2 input: AT Translated Set 2 keyboard as /class/input/input0 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 4, 65536 bytes) TCP bind hash table entries: 16384 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered TCP bic registered Using IPI Shortcut mode ACPI wakeup devices: LID SLPB UART EXP0 EXP1 EXP2 EXP3 PCI1 USB0 USB1 USB3 USB7 AC9M ACPI: (supports S0 S3 S4 S5) kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 152k freed IBM TrackPoint firmware: 0x0e, buttons: 3/3 input: TPPS/2 IBM TrackPoint as /class/input/input1 NET: Registered protocol family 1 hw_random: RNG not detected Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected an Intel 915GM Chipset. agpgart: AGP aperture is 256M @ 0x0 usbcore: registered new driver usbfs usbcore: registered new driver hub tg3.c:v3.47 (Dec 28, 2005) ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:02:00.0 to 64 eth0: Tigon3 [partno(BCM95751M) rev 4101 PHY(5750)] (PCI Express) 10/100/1000BaseT Ethernet 00:01:6c:ca:20:70 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1] eth0: dma_rwctrl[76180000] Real Time Clock Driver v1.12 USB Universal Host Controller Interface driver v2.3 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 169, io base 0x00001800 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected input: PC Speaker as /class/input/input2 ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 225 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: irq 225, io base 0x00001820 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected NET: Registered protocol family 23 ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 233 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: irq 233, io base 0x00001840 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 50 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.3: irq 50, io base 0x00001860 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 19 (level, low) -> IRQ 50 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:1d.7: irq 50, io mem 0xa8000000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 22 (level, low) -> IRQ 185 PCI: Setting latency timer of device 0000:00:1e.2 to 64 pnp: Device 00:0a activated. nsc-ircc, Found chip at base=0x000 nsc-ircc, driver loaded (Dag Brattli) IrDA: Registered device irda0 nsc-ircc, Using dongle: IBM31T1100 or Temic TFDS6000/TFDS6500 ieee80211_crypt: registered algorithm 'NULL' ieee80211: 802.11 data/management/control stack, git-1.1.7 ieee80211: Copyright (C) 2004-2005 Intel Corporation ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, git-1.0.8 ipw2200: Copyright(c) 2003-2005 Intel Corporation usb 3-2: new full speed USB device using uhci_hcd and address 2 intel8x0_measure_ac97_clock: measured 55516 usecs intel8x0: clocking to 48000 ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 169 Yenta: CardBus bridge found at 0000:04:00.0 [1014:056c] Yenta: ISA IRQ mask 0x04b0, PCI irq 169 Socket status: 30000006 pcmcia: parent PCI bridge I/O window: 0x4000 - 0x7fff cs: IO port probe 0x4000-0x7fff: clean. pcmcia: parent PCI bridge Memory window: 0xa8400000 - 0xb7ffffff pcmcia: parent PCI bridge Memory window: 0xd0000000 - 0xd7ffffff ACPI: PCI Interrupt 0000:04:02.0[A] -> GSI 21 (level, low) -> IRQ 58 ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection Adding 497972k swap on /dev/sda6. Priority:-1 extents:1 across:497972k EXT3 FS on sda5, internal journal ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU] (supports 8 throttling states) acpi-cpufreq: CPU0 - ACPI performance management activated. Machine check exception polling timer started. hdaps: IBM ThinkPad T43 detected. hdaps: initial latch check good (0x01). hdaps: device successfully initialized. input: hdaps as /class/input/input3 hdaps: driver successfully loaded. Non-volatile memory driver v1.2 kjournald starting. Commit interval 5 seconds EXT3 FS on sda7, internal journal EXT3-fs: mounted filesystem with ordered data mode. NTFS driver 2.1.25 [Flags: R/O MODULE]. NTFS volume version 3.1. pcmcia: Detected deprecated PCMCIA ioctl usage. pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools. pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details. cs: IO port probe 0x100-0x4ff: excluding 0x3f0-0x3ff 0x4d0-0x4d7 cs: IO port probe 0x800-0x8ff: clean. cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff cs: IO port probe 0xa00-0xaff: clean. ACPI: Battery Slot [BAT0] (battery present) ACPI: AC Adapter [AC] (on-line) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID] ACPI: Sleep Button (CM) [SLPB] ACPI: Thermal Zone [THM0] (61 C) NET: Registered protocol family 17