From: Zhou Yanjie <zhouyanjie@zoho.com>
To: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@vger.kernel.org, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org, robh+dt@kernel.org,
paul.burton@mips.com, paulburton@kernel.org, jhogan@kernel.org,
mripard@kernel.org, shawnguo@kernel.org, mark.rutland@arm.com,
syq@debian.org, ralf@linux-mips.org, heiko@sntech.de,
icenowy@aosc.io, laurent.pinchart@ideasonboard.com,
krzk@kernel.org, geert+renesas@glider.be,
prasannatsmkumar@gmail.com, sernia.zhou@foxmail.com,
zhenwenjin@gmail.com, 772753199@qq.com
Subject: Re: [PATCH v4 4/6] MIPS: Ingenic: Initial YSH & ATIL CU Neo board support.
Date: Fri, 29 Nov 2019 15:48:04 +0800 [thread overview]
Message-ID: <5DE0CD34.6070504@zoho.com> (raw)
In-Reply-To: <1574944293.3.0@crapouillou.net>
Hi Paul,
On 2019年11月28日 20:31, Paul Cercueil wrote:
> Hi Zhou,
>
>
> Le jeu., nov. 28, 2019 at 13:11, Zhou Yanjie <zhouyanjie@zoho.com> a
> écrit :
>> Hi Paul,
>>
>> On 2019年11月28日 00:57, Paul Cercueil wrote:
>>> Hi Zhou,
>>>
>>>
>>> Le mer., nov. 27, 2019 at 01:06, Zhou Yanjie <zhouyanjie@zoho.com>
>>> a \x7fécrit :
>>>> Add a device tree for the Ingenic X1000 based YSH & ATIL CU Neo board.
>>>> Note that this is unselectable via Kconfig until the X1000 SoC is made
>>>> selectable in a later commit.
>>>>
>>>> Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
>>>> ---
>>>>
>>>> Notes:
>>>> v1->v2:
>>>> Rebase on top of mips-next, use TCU for system timer and
>>>> \x7f\x7fclocksource.
>>>>
>>>> v2->v3:
>>>> No change.
>>>>
>>>> v3->v4:
>>>> 1.Adjust "model" in "cu1000.dts" to match the description in
>>>> \x7f\x7f"devices.yaml".
>>>> 2.Adjust "bool" in "Kconfig" to avoid duplicate names with
>>>> \x7f\x7fsubsequent boards.
>>>>
>>>> arch/mips/boot/dts/ingenic/Makefile | 1 +
>>>> arch/mips/boot/dts/ingenic/cu1000.dts | 52 ++++++++++++++++++
>>>> arch/mips/configs/cu1000_defconfig | 100
>>>> \x7f\x7f++++++++++++++++++++++++++++++++++
>>>> arch/mips/jz4740/Kconfig | 4 ++
>>>> 4 files changed, 157 insertions(+)
>>>> create mode 100644 arch/mips/boot/dts/ingenic/cu1000.dts
>>>> create mode 100644 arch/mips/configs/cu1000_defconfig
>>>>
>>>> diff --git a/arch/mips/boot/dts/ingenic/Makefile
>>>> \x7f\x7fb/arch/mips/boot/dts/ingenic/Makefile
>>>> index 9cc4844..f6db7bb 100644
>>>> --- a/arch/mips/boot/dts/ingenic/Makefile
>>>> +++ b/arch/mips/boot/dts/ingenic/Makefile
>>>> @@ -2,5 +2,6 @@
>>>> dtb-$(CONFIG_JZ4740_QI_LB60) += qi_lb60.dtb
>>>> dtb-$(CONFIG_JZ4770_GCW0) += gcw0.dtb
>>>> dtb-$(CONFIG_JZ4780_CI20) += ci20.dtb
>>>> +dtb-$(CONFIG_X1000_CU1000) += cu1000.dtb
>>>>
>>>> obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
>>>> diff --git a/arch/mips/boot/dts/ingenic/cu1000.dts
>>>> \x7f\x7fb/arch/mips/boot/dts/ingenic/cu1000.dts
>>>> new file mode 100644
>>>> index 00000000..f92f6af
>>>> --- /dev/null
>>>> +++ b/arch/mips/boot/dts/ingenic/cu1000.dts
>>>> @@ -0,0 +1,52 @@
>>>> +// SPDX-License-Identifier: GPL-2.0
>>>> +/dts-v1/;
>>>> +
>>>> +#include "x1000.dtsi"
>>>> +#include <dt-bindings/gpio/gpio.h>
>>>> +#include <dt-bindings/clock/ingenic,tcu.h>
>>>> +
>>>> +/ {
>>>> + compatible = "yna,cu1000", "ingenic,x1000";
>>>> + model = "YSH & ATIL General Board CU Neo";
>>>> +
>>>> + aliases {
>>>> + serial2 = &uart2;
>>>> + };
>>>> +
>>>> + chosen {
>>>> + stdout-path = &uart2;
>>>> + };
>>>> +
>>>> + memory {
>>>> + device_type = "memory";
>>>> + reg = <0x0 0x04000000>;
>>>> + };
>>>> +};
>>>> +
>>>> +&exclk {
>>>> + clock-frequency = <24000000>;
>>>> +};
>>>> +
>>>> +&tcu {
>>>> + /* 1500 kHz for the system timer and clocksource */
>>>> + assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
>>>> + assigned-clock-rates = <1500000>, <1500000>;
>>>> +
>>>> + /* Use channel #1 for the system timer channel #2 for the
>>>> \x7f\x7fclocksource */
>>>> + ingenic,pwm-channels-mask = <0xfa>;
>>>
>>> From the mask used, I'm gessing that you're reserving channels #0
>>> and \x7f#2, not #1 and #2.
>>>
>>
>> My fault, you are right, it use channels #0 and #2.
>>
>>>> +};
>>>> +
>>>> +&uart2 {
>>>> + status = "okay";
>>>> +
>>>> + pinctrl-names = "default";
>>>> + pinctrl-0 = <&pins_uart2>;
>>>> +};
>>>> +
>>>> +&pinctrl {
>>>> + pins_uart2: uart2 {
>>>> + function = "uart2";
>>>> + groups = "uart2-data-d";
>>>> + bias-disable;
>>>> + };
>>>> +};
>>>> diff --git a/arch/mips/configs/cu1000_defconfig
>>>> \x7f\x7fb/arch/mips/configs/cu1000_defconfig
>>>> new file mode 100644
>>>> index 00000000..88729ee
>>>> --- /dev/null
>>>> +++ b/arch/mips/configs/cu1000_defconfig
>>>> @@ -0,0 +1,100 @@
>>>> +CONFIG_LOCALVERSION_AUTO=y
>>>> +CONFIG_KERNEL_GZIP=y
>>>> +CONFIG_SYSVIPC=y
>>>> +CONFIG_NO_HZ_IDLE=y
>>>> +CONFIG_HIGH_RES_TIMERS=y
>>>> +CONFIG_PREEMPT=y
>>>> +CONFIG_IKCONFIG=y
>>>> +CONFIG_IKCONFIG_PROC=y
>>>> +CONFIG_LOG_BUF_SHIFT=14
>>>> +CONFIG_CGROUPS=y
>>>> +CONFIG_MEMCG=y
>>>> +CONFIG_MEMCG_KMEM=y
>>>> +CONFIG_CGROUP_SCHED=y
>>>> +CONFIG_CGROUP_FREEZER=y
>>>> +CONFIG_CGROUP_DEVICE=y
>>>> +CONFIG_CGROUP_CPUACCT=y
>>>> +CONFIG_NAMESPACES=y
>>>> +CONFIG_USER_NS=y
>>>> +CONFIG_BLK_DEV_INITRD=y
>>>> +CONFIG_INITRAMFS_SOURCE="arch/mips/boot/ramdisk.cpio.gz"
>>>> +CONFIG_CC_OPTIMIZE_FOR_SIZE=y
>>>> +CONFIG_SYSCTL_SYSCALL=y
>>>> +CONFIG_KALLSYMS_ALL=y
>>>> +CONFIG_EMBEDDED=y
>>>> +# CONFIG_VM_EVENT_COUNTERS is not set
>>>> +# CONFIG_COMPAT_BRK is not set
>>>> +CONFIG_SLAB=y
>>>> +CONFIG_MACH_INGENIC=y
>>>> +CONFIG_X1000_CU1000=y
>>>> +CONFIG_HIGHMEM=y
>>>> +CONFIG_HZ_100=y
>>>> +CONFIG_HZ=100
>>>
>>> This line looks malformed.
>>
>> Ok, I'll remove it in v7.
>>
>>>
>>>> +# CONFIG_SECCOMP is not set
>>>> +# CONFIG_SUSPEND is not set
>>>> +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
>>>> +# CONFIG_COMPACTION is not set
>>>> +CONFIG_CMA=y
>>>> +CONFIG_CMA_AREAS=7
>>>> +CONFIG_UEVENT_HELPER=y
>>>> +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
>>>> +CONFIG_DEVTMPFS=y
>>>> +# CONFIG_FW_LOADER is not set
>>>> +# CONFIG_ALLOW_DEV_COREDUMP is not set
>>>> +# CONFIG_INPUT_MOUSEDEV is not set
>>>> +# CONFIG_INPUT_KEYBOARD is not set
>>>> +# CONFIG_INPUT_MOUSE is not set
>>>> +# CONFIG_SERIO is not set
>>>> +CONFIG_VT_HW_CONSOLE_BINDING=y
>>>> +CONFIG_LEGACY_PTY_COUNT=2
>>>> +CONFIG_SERIAL_EARLYCON=y
>>>> +CONFIG_SERIAL_8250=y
>>>> +CONFIG_SERIAL_8250_CONSOLE=y
>>>> +CONFIG_SERIAL_8250_NR_UARTS=3
>>>> +CONFIG_SERIAL_8250_RUNTIME_UARTS=3
>>>> +CONFIG_SERIAL_8250_INGENIC=y
>>>> +CONFIG_SERIAL_OF_PLATFORM=y
>>>> +# CONFIG_HW_RANDOM is not set
>>>> +CONFIG_GPIO_SYSFS=y
>>>> +# CONFIG_HWMON is not set
>>>> +# CONFIG_LCD_CLASS_DEVICE is not set
>>>> +# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
>>>> +# CONFIG_VGA_CONSOLE is not set
>>>> +# CONFIG_HID is not set
>>>> +# CONFIG_USB_SUPPORT is not set
>>>> +# CONFIG_IOMMU_SUPPORT is not set
>>>> +CONFIG_NVMEM=y
>>>> +CONFIG_NVMEM_SYSFS=y
>>>> +CONFIG_EXT4_FS=y
>>>> +# CONFIG_DNOTIFY is not set
>>>> +CONFIG_PROC_KCORE=y
>>>> +# CONFIG_PROC_PAGE_MONITOR is not set
>>>> +CONFIG_TMPFS=y
>>>> +CONFIG_CONFIGFS_FS=y
>>>> +CONFIG_NLS=y
>>>> +CONFIG_NLS_CODEPAGE_936=y
>>>> +CONFIG_NLS_CODEPAGE_950=y
>>>> +CONFIG_NLS_ASCII=y
>>>> +CONFIG_NLS_ISO8859_1=y
>>>> +CONFIG_NLS_UTF8=y
>>>> +CONFIG_CRYPTO_ECHAINIV=y
>>>> +CONFIG_CRYPTO_AES=y
>>>> +CONFIG_CRYPTO_DEFLATE=y
>>>> +CONFIG_CRYPTO_LZO=y
>>>> +CONFIG_PRINTK_TIME=y
>>>> +CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15
>>>> +CONFIG_CONSOLE_LOGLEVEL_QUIET=15
>>>> +CONFIG_MESSAGE_LOGLEVEL_DEFAULT=7
>>>> +CONFIG_DEBUG_INFO=y
>>>> +CONFIG_STRIP_ASM_SYMS=y
>>>> +CONFIG_DEBUG_FS=y
>>>> +CONFIG_MAGIC_SYSRQ=y
>>>> +CONFIG_PANIC_ON_OOPS=y
>>>> +CONFIG_PANIC_TIMEOUT=10
>>>> +# CONFIG_SCHED_DEBUG is not set
>>>> +# CONFIG_DEBUG_PREEMPT is not set
>>>> +CONFIG_STACKTRACE=y
>>>> +# CONFIG_FTRACE is not set
>>>> +CONFIG_CMDLINE_BOOL=y
>>>> +CONFIG_CMDLINE="console=ttyS2,115200n8 mem=32M@0x0 earlycon
>>>> \x7f\x7fclk_ignore_unused"
>>>
>>> You already specify the stdout-path in the devicetree, no need to
>>> pass \x7fthe "console" parameter.
>>>
>>
>> According the test log , if remove "console=ttyS2,115200n8", serial
>> will not
>> initialized and will stuck after:
>>
>> [ 0.016815] printk: bootconsole [x1000_uart0] disabled
>>
>> if remove both "console=ttyS2,115200n8" and "earlycon" it will stuck
>> after:
>>
>> Starting kernel ...
>>
>> So I think both the "earlycon" and the "console=ttyS2,115200n8
>> earlycon" should be retained.
>
> There must be something wrong with your kernel config. It works here.
>
> Use this as your stdout-path: "serial2:115200n8", unset
> CONFIG_CMDLINE_OVERRIDE, enable MIPS_CMDLINE_DTB_EXTEND, and just use
> "earlycon clk_ignore_unused" in the devicetree's bootargs. That should
> do it.
>
It works, I will change it in v6.
>>
>>> For the "mem" parameter, it's already set in the devicetree, so no
>>> \x7fneed to set it again here.
>>> Besides, in the devicetree it is set to 64 MiB.
>>
>> Ok, I'll remove them in v7.
>>
>>>
>>> Why is clk_ignore_unused needed?
>>
>> In fact, I also don't know why "clk_ignore_unused" needed.
>> This part of the parameter is copied from ci20_defconfig,
>> but according to the test, if remove "clk_ignore_unused",
>> it will stuck after :
>>
>> [ 0.374361] printk: bootconsole [x1000_uart0] disabled
>>
>> Differeent from the case where "console=ttyS2,115200n8" is removed,
>> the serial is successfully initialized this time.
>>
>> So I think "clk_ignore_unused" should be retained.
>
> It locks up because Linux disables a clock that is required for the
> system. This clock should be requested and enabled by a client driver.
> Could you investigate which clock is the problem?
>
I also don't have any good ideas now, but I will try to investigate it.
Thanks and best regards!
> @Paul Burton: do you remember why it was needed on CI20?
>
> In the meantime I suppose "clk_ignore_unused" is fine.
>
> Cheers,
> -Paul
>
>>>
>>>> +CONFIG_CMDLINE_OVERRIDE=y
>>>> diff --git a/arch/mips/jz4740/Kconfig b/arch/mips/jz4740/Kconfig
>>>> index 6b96844..ccaf507 100644
>>>> --- a/arch/mips/jz4740/Kconfig
>>>> +++ b/arch/mips/jz4740/Kconfig
>>>> @@ -16,6 +16,10 @@ config JZ4780_CI20
>>>> bool "MIPS Creator CI20"
>>>> select MACH_JZ4780
>>>>
>>>> +config X1000_CU1000
>>>> + bool "YSH & ATIL General Module CU1000"
>>>> + select MACH_X1000
>>>> +
>>>> endchoice
>>>>
>>>> config MACH_JZ4740
>>>> --
>>>> 2.7.4
>>>>
>>>>
>>>
>>>
>>
>>
>>
>
>
next prev parent reply other threads:[~2019-11-29 7:49 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-11-26 17:06 Add initial support for Ingenic X1000 SoC and Y&A CU Neo board v4 Zhou Yanjie
2019-11-26 17:06 ` [PATCH v4 1/6] MIPS: Ingenic: Initial X1000 support Zhou Yanjie
2019-11-26 17:06 ` [PATCH v4 2/6] dt-bindings: Document yna vendor-prefix Zhou Yanjie
2019-11-26 17:06 ` [PATCH v4 3/6] dt-bindings: MIPS: Add Ingenic XBurst based boards Zhou Yanjie
2019-11-26 17:06 ` [PATCH v4 4/6] MIPS: Ingenic: Initial YSH & ATIL CU Neo board support Zhou Yanjie
2019-11-27 16:57 ` Paul Cercueil
2019-11-28 5:11 ` Zhou Yanjie
2019-11-28 12:31 ` Paul Cercueil
2019-11-29 7:48 ` Zhou Yanjie [this message]
2019-11-26 17:06 ` [PATCH v4 5/6] MIPS: X1000: Add pdma controller DT node Zhou Yanjie
2019-11-27 16:48 ` Paul Cercueil
2019-11-28 3:26 ` Zhou Yanjie
2019-11-26 17:06 ` [PATCH v4 6/6] MIPS: CU1000: Update defconfig for pdma controller Zhou Yanjie
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5DE0CD34.6070504@zoho.com \
--to=zhouyanjie@zoho.com \
--cc=772753199@qq.com \
--cc=devicetree@vger.kernel.org \
--cc=geert+renesas@glider.be \
--cc=heiko@sntech.de \
--cc=icenowy@aosc.io \
--cc=jhogan@kernel.org \
--cc=krzk@kernel.org \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mips@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mripard@kernel.org \
--cc=paul.burton@mips.com \
--cc=paul@crapouillou.net \
--cc=paulburton@kernel.org \
--cc=prasannatsmkumar@gmail.com \
--cc=ralf@linux-mips.org \
--cc=robh+dt@kernel.org \
--cc=sernia.zhou@foxmail.com \
--cc=shawnguo@kernel.org \
--cc=syq@debian.org \
--cc=zhenwenjin@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).