Re: [PATCH 5/6] riscv: microchip: mpfs: drop duplicated MMC/SDHC node

[Geert Uytterhoeven <geert@linux-m68k.org>]

Hi Krzysztof,

On Thu, Aug 19, 2021 at 5:45 PM Krzysztof Kozlowski
<krzysztof.kozlowski@canonical.com> wrote:
> Devicetree source is a description of hardware and hardware has only one
> block @20008000 which can be configured either as eMMC or SDHC.  Having
> two node for different modes is an obscure, unusual and confusing way to
> configure it.  Instead the board file is supposed to customize the block
> to its needs, e.g. to SDHC mode.
>
> This fixes dtbs_check warning:
>   arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dt.yaml: sdhc@20008000: $nodename:0: 'sdhc@20008000' does not match '^mmc(@.*)?$'
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>

Thanks for your patch!

> --- a/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> +++ b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> @@ -43,8 +43,16 @@ &serial3 {
>         status = "okay";
>  };
>
> -&sdcard {
> +&mmc {
>         status = "okay";
> +
> +       disable-wp;
> +       cap-sd-highspeed;
> +       card-detect-delay = <200>;
> +       sd-uhs-sdr12;
> +       sd-uhs-sdr25;
> +       sd-uhs-sdr50;
> +       sd-uhs-sdr104;
>  };
>
>  &emac0 {
> diff --git a/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi b/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> index cb54da0cc3c4..c4ccd7e4d3eb 100644
> --- a/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> +++ b/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> @@ -262,25 +262,7 @@ serial3: serial@20104000 {
>                         status = "disabled";
>                 };
>
> -               emmc: mmc@20008000 {
> -                       compatible = "cdns,sd4hc";
> -                       reg = <0x0 0x20008000 0x0 0x1000>;
> -                       interrupt-parent = <&plic>;
> -                       interrupts = <88 89>;

Note that the other node has only a single interrupt.
Which one is correct?

> -                       pinctrl-names = "default";
> -                       clocks = <&clkcfg 6>;
> -                       bus-width = <4>;
> -                       cap-mmc-highspeed;
> -                       mmc-ddr-3_3v;
> -                       max-frequency = <200000000>;
> -                       non-removable;
> -                       no-sd;
> -                       no-sdio;
> -                       voltage-ranges = <3300 3300>;
> -                       status = "disabled";
> -               };
> -
> -               sdcard: sdhc@20008000 {
> +               mmc: mmc@20008000 {
>                         compatible = "cdns,sd4hc";
>                         reg = <0x0 0x20008000 0x0 0x1000>;
>                         interrupt-parent = <&plic>;
> @@ -288,13 +270,6 @@ sdcard: sdhc@20008000 {
>                         pinctrl-names = "default";
>                         clocks = <&clkcfg 6>;
>                         bus-width = <4>;

I think bus-width should be moved to the board .dts, too.

> -                       disable-wp;
> -                       cap-sd-highspeed;
> -                       card-detect-delay = <200>;
> -                       sd-uhs-sdr12;
> -                       sd-uhs-sdr25;
> -                       sd-uhs-sdr50;
> -                       sd-uhs-sdr104;
>                         max-frequency = <200000000>;
>                         status = "disabled";
>                 };

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds