RE: [PATCH v3 1/2] mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories

[Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>]

Hi Tudor,

> -----Original Message-----
> From: Tudor Ambarus [mailto:tudor.ambarus@microchip.com]
> Sent: Wednesday, October 17, 2018 1:31 PM
> To: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>; Boris Brezillon
> <boris.brezillon@bootlin.com>
> Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>; marek.vasut@gmail.com;
> dwmw2@infradead.org; computersforpeace@gmail.com; richard@nod.at;
> linux-kernel@vger.kernel.org; nicolas.ferre@microchip.com;
> cyrille.pitchen@microchip.com; linux-mtd@lists.infradead.org; linux-arm-
> kernel@lists.infradead.org; Cristian.Birsan@microchip.com
> Subject: Re: [PATCH v3 1/2] mtd: spi-nor: add support to non-uniform SFDP SPI
> NOR flash memories
> 
> Hi, Yogesh,
> 
> On 10/17/2018 10:46 AM, Yogesh Narayan Gaur wrote:
> > Hi Boris,
> >
> >> -----Original Message-----
> >> From: Boris Brezillon [mailto:boris.brezillon@bootlin.com]
> >> Sent: Wednesday, October 17, 2018 1:00 PM
> >> To: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
> >> Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>; Tudor Ambarus
> >> <tudor.ambarus@microchip.com>; marek.vasut@gmail.com;
> >> dwmw2@infradead.org; computersforpeace@gmail.com; richard@nod.at;
> >> linux-kernel@vger.kernel.org; nicolas.ferre@microchip.com;
> >> cyrille.pitchen@microchip.com; linux-mtd@lists.infradead.org;
> >> linux-arm- kernel@lists.infradead.org; Cristian.Birsan@microchip.com
> >> Subject: Re: [PATCH v3 1/2] mtd: spi-nor: add support to non-uniform
> >> SFDP SPI NOR flash memories
> >>
> >> On Wed, 17 Oct 2018 09:10:45 +0200
> >> Boris Brezillon <boris.brezillon@bootlin.com> wrote:
> >>
> >>> On Wed, 17 Oct 2018 09:07:24 +0200
> >>> Boris Brezillon <boris.brezillon@bootlin.com> wrote:
> >>>
> >>>> On Wed, 17 Oct 2018 02:07:43 +0000
> >>>> Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com> wrote:
> >>>>
> >>>>>>
> >>>>> Actually there is no entry of s25fs512s in current spi-nor.c file.
> >>>>> For my connected flash part, jedec ID read points to s25fl512s. I
> >>>>> have asked my board team to confirm the name of exact connected
> >>>>> flash part. When I check the data sheet of s25fs512s, it also
> >>>>> points to the same Jedec ID information. { "s25fl512s",
> >>>>> INFO(0x010220, 0x4d00, 256
> >>>>> * 1024, 256, ....}
> >>>>>
> >>>>> But as stated earlier, if I skip reading SFDP or read using 1-1-1
> >>>>> protocol then read are always correct. For 1-4-4 protocol read are
> >>>>> wrong and on further debugging found that Read code of 0x6C is
> >>>>> being send as opcode instead of 0xEC.
> >>>>>
> >>>>> If I revert this patch, reads are working fine.
> >>>>
> >>>> Can you try with the following patch?
> >>>>
> >>>
> >>> Hm, nevermind. The problem is actually not related to 4B vs non-4B
> >>> mode but 1-1-4 vs 1-4-4 modes.
> > Yes, that's only I have stated in my first mail that instead of 1-4-4 mode read
> opcode is being sent for 1-1-4 mode.
> >>>
> >>
> >> Can you try with this patch applied?
> >>
> > With suggested patch, read for protocol 1-4-4 working correctly.
> >
> > 	[    1.625360] m25p80 spi0.0: found s25fl512s, expected m25p80
> > 	[    1.631094] m25p80 spi0.0: failed to parse SMPT (err = -22)
> > 	[    1.636661] 261 8c4c780 opcode(read:eb, pp:2, erase:d8)
> > 	[    1.641878] 266 8c4c780 opcode(read:ec, pp:12, erase:dc)
> > 	[    1.647200] m25p80 spi0.0: s25fl512s (65536 Kbytes)
> >
> > Without this patch, param_headers are getting freed and restoring previous
> erase map i.e. opcode related to 1-1-4 protocol.
> >
> 
> Can you add some prints in spi_nor_parse_smpt() to isolate what's failing? We
> should understand whether it's something wrong in spi_nor_parse_smpt() or the
> s25fs512s smpt table does not respect the standard.
> 

It's returning failure from below point in func spi_nor_get_map_in_use()

        /* Find the matching configuration map */
        while (SMPT_MAP_ID(smpt[i]) != map_id) {
                if (smpt[i] & SMPT_DESC_END) {
                        printk("%d %s \n", __LINE__, __func__);
                        goto out;
                }
--
Regards
Yogesh Gaur.

> Thanks,
> ta
>