linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: <Claudiu.Beznea@microchip.com>
To: <daniel.lezcano@linaro.org>, <robh+dt@kernel.org>,
	<mark.rutland@arm.com>, <Nicolas.Ferre@microchip.com>,
	<alexandre.belloni@bootlin.com>,
	<Ludovic.Desroches@microchip.com>, <tglx@linutronix.de>
Cc: <devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH 2/5] clocksource/drivers/timer-microchip-pit64b: add Microchip PIT64B support
Date: Mon, 8 Apr 2019 11:48:19 +0000	[thread overview]
Message-ID: <c2ae013a-0d7a-e415-f159-a1ba26c8257b@microchip.com> (raw)
In-Reply-To: <a738fce5-1108-34d7-d255-dfcb86f51c56@linaro.org>

Hi Daniel,

On 08.04.2019 11:43, Daniel Lezcano wrote:
> External E-Mail
> 
> 
> Hi Claudiu,
> 
> On 14/03/2019 17:26, Claudiu.Beznea@microchip.com wrote:
>> From: Claudiu Beznea <claudiu.beznea@microchip.com>
>>
>> Add driver for Microchip PIT64B timer. Timer could be used in continuous
>> mode or oneshot mode. The hardware has 2x32 bit registers for period
>> emulating a 64 bit timer. The LSB_PR and MSB_PR registers are used to set
>> the period value (compare value). TLSB and TMSB keeps the current value
>> of the counter. After a compare the TLSB and TMSB register resets. Apart
>> from this the hardware has SMOD bit in mode register that allow to
>> reconfigure the timer without reset and start commands (start command
>> while timer is active is ignored).
>> The driver uses PIT64B timer as clocksource or clockevent. First requested
>> timer would be registered as clockevent, second one would be registered as
>> clocksource.
> 
> Even if that was done this way before, assuming the DT describes the
> clockevent at the first place and then the clocksource, it is a fragile
> approach.
> 
> What about using one of these approach?
> 
> eg.
> 
> arch/arm/boot/dts/at91sam9261ek.dts
> 
> chosen {
> 	bootargs = "rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs rw";
>                 stdout-path = "serial0:115200n8";
> 
> 	clocksource {
> 		timer = <&timer0>;
> 	};
> 
>         clockevent {
> 		timer = <&timer1>;
>         };
> };
> 
> or
> 
> arch/arm/boot/dts/integratorap.dts
> 
> aliases {
> 	arm,timer-primary = &timer2;
> 	arm,timer-secondary = &timer1;
> };
> 
> So we can have control of what is the clocksource or the clockevent.
> That is particulary handy in case of multiple channels.

Sure, I will look over these.

Thank you,
Claudiu Beznea

> 
> Not sure if we can replace the 'arm,timer_primary' to 'clocksource'.
> 
> Rob? What is your opinion?
> 
>> Individual PIT64B hardware resources were used for clocksource
>> and clockevent to be able to support high resolution timers with this
>> hardware implementation.
>>
>> Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
>> ---
>>  drivers/clocksource/Kconfig                  |   6 +
>>  drivers/clocksource/Makefile                 |   1 +
>>  drivers/clocksource/timer-microchip-pit64b.c | 464 +++++++++++++++++++++++++++
>>  3 files changed, 471 insertions(+)
>>  create mode 100644 drivers/clocksource/timer-microchip-pit64b.c
>>
>> diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
>> index 5d93e580e5dc..2ad6f881a0bb 100644
>> --- a/drivers/clocksource/Kconfig
>> +++ b/drivers/clocksource/Kconfig
>> @@ -448,6 +448,12 @@ config OXNAS_RPS_TIMER
>>  config SYS_SUPPORTS_SH_CMT
>>          bool
>>  
>> +config MICROCHIP_PIT64B
>> +	bool "Microchip PIT64B support"
>> +	depends on OF || COMPILE_TEST
>> +	help
>> +	  This option enables Microchip PIT64B timer.
>> +
>>  config MTK_TIMER
>>  	bool "Mediatek timer driver" if COMPILE_TEST
>>  	depends on HAS_IOMEM
>> diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
>> index c4a8e9ef932a..c53fa12b9b94 100644
>> --- a/drivers/clocksource/Makefile
>> +++ b/drivers/clocksource/Makefile
>> @@ -35,6 +35,7 @@ obj-$(CONFIG_U300_TIMER)	+= timer-u300.o
>>  obj-$(CONFIG_SUN4I_TIMER)	+= timer-sun4i.o
>>  obj-$(CONFIG_SUN5I_HSTIMER)	+= timer-sun5i.o
>>  obj-$(CONFIG_MESON6_TIMER)	+= timer-meson6.o
>> +obj-$(CONFIG_MICROCHIP_PIT64B)	+= timer-microchip-pit64b.o
>>  obj-$(CONFIG_TEGRA_TIMER)	+= timer-tegra20.o
>>  obj-$(CONFIG_VT8500_TIMER)	+= timer-vt8500.o
>>  obj-$(CONFIG_NSPIRE_TIMER)	+= timer-zevio.o
>> diff --git a/drivers/clocksource/timer-microchip-pit64b.c b/drivers/clocksource/timer-microchip-pit64b.c
>> new file mode 100644
>> index 000000000000..6787aa98ef01
>> --- /dev/null
>> +++ b/drivers/clocksource/timer-microchip-pit64b.c
>> @@ -0,0 +1,464 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +//
>> +// Copyright (C) 2019 Microchip Technology Inc.
>> +// Copyright (C) 2019 Claudiu Beznea (claudiu.beznea@microchip.com)
>> +
>> +#include <linux/clk.h>
>> +#include <linux/clockchips.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/of_address.h>
>> +#include <linux/of_irq.h>
>> +#include <linux/sched_clock.h>
>> +#include <linux/slab.h>
>> +
>> +#define MCHP_PIT64B_CR		0x00	/* Control Register */
>> +#define MCHP_PIT64B_CR_START	BIT(0)
>> +#define MCHP_PIT64B_CR_SWRST	BIT(8)
>> +
>> +#define MCHP_PIT64B_MR		0x04	/* Mode Register */
>> +#define MCHP_PIT64B_MR_CONT	BIT(0)
>> +#define MCHP_PIT64B_MR_SGCLK	BIT(3)
>> +#define MCHP_PIT64B_MR_SMOD	BIT(4)
>> +#define MCHP_PIT64B_MR_PRES	GENMASK(11, 8)
>> +
>> +#define MCHP_PIT64B_LSB_PR	0x08	/* LSB Period Register */
>> +
>> +#define MCHP_PIT64B_MSB_PR	0x0C	/* MSB Period Register */
>> +
>> +#define MCHP_PIT64B_IER		0x10	/* Interrupt Enable Register */
>> +#define MCHP_PIT64B_IER_PERIOD	BIT(0)
>> +
>> +#define MCHP_PIT64B_ISR		0x1C	/* Interrupt Status Register */
>> +#define MCHP_PIT64B_ISR_PERIOD	BIT(0)
>> +
>> +#define MCHP_PIT64B_TLSBR	0x20	/* Timer LSB Register */
>> +
>> +#define MCHP_PIT64B_TMSBR	0x24	/* Timer MSB Register */
>> +
>> +#define MCHP_PIT64B_PRES_MAX	0x10
>> +#define MCHP_PIT64B_DEF_FREQ	2500000UL	/* 2.5 MHz */
>> +#define MCHP_PIT64B_LSBMASK	GENMASK_ULL(31, 0)
>> +#define MCHP_PIT64B_PRESCALER(p)	(MCHP_PIT64B_MR_PRES & ((p) << 8))
>> +
>> +#define MCHP_PIT64B_NAME	"pit64b"
>> +
>> +struct mchp_pit64b_common_data {
>> +	void __iomem *base;
>> +	struct clk *pclk;
>> +	struct clk *gclk;
>> +	u64 cycles;
>> +	u8 pres;
>> +};
>> +
>> +struct mchp_pit64b_clksrc_data {
>> +	struct clocksource *clksrc;
>> +	struct mchp_pit64b_common_data *cd;
>> +};
>> +
>> +struct mchp_pit64b_clkevt_data {
>> +	struct clock_event_device *clkevt;
>> +	struct mchp_pit64b_common_data *cd;
>> +};
>> +
>> +static struct mchp_pit64b_data {
>> +	struct mchp_pit64b_clksrc_data *csd;
>> +	struct mchp_pit64b_clkevt_data *ced;
>> +} data;
>> +
>> +static inline u32 mchp_pit64b_read(void __iomem *base, u32 offset)
>> +{
>> +	return readl_relaxed(base + offset);
>> +}
>> +
>> +static inline void mchp_pit64b_write(void __iomem *base, u32 offset, u32 val)
>> +{
>> +	writel_relaxed(val, base + offset);
>> +}
>> +
>> +static inline u64 mchp_pit64b_get_period(void __iomem *base)
>> +{
>> +	u32 lsb, msb;
>> +
>> +	/* LSB must be read first to guarantee an atomic read of the 64 bit
>> +	 * timer.
>> +	 */
>> +	lsb = mchp_pit64b_read(base, MCHP_PIT64B_TLSBR);
>> +	msb = mchp_pit64b_read(base, MCHP_PIT64B_TMSBR);
>> +
>> +	return (((u64)msb << 32) | lsb);
>> +}
>> +
>> +static inline void mchp_pit64b_set_period(void __iomem *base, u64 cycles)
>> +{
>> +	u32 lsb, msb;
>> +
>> +	lsb = cycles & MCHP_PIT64B_LSBMASK;
>> +	msb = cycles >> 32;
>> +
>> +	/* LSB must be write last to guarantee an atomic update of the timer
>> +	 * even when SMOD=1.
>> +	 */
>> +	mchp_pit64b_write(base, MCHP_PIT64B_MSB_PR, msb);
>> +	mchp_pit64b_write(base, MCHP_PIT64B_LSB_PR, lsb);
>> +}
>> +
>> +static inline void mchp_pit64b_reset(struct mchp_pit64b_common_data *data,
>> +				     u32 mode, bool irq_ena)
>> +{
>> +	mode |= MCHP_PIT64B_PRESCALER(data->pres);
>> +	if (data->gclk)
>> +		mode |= MCHP_PIT64B_MR_SGCLK;
>> +
>> +	mchp_pit64b_write(data->base, MCHP_PIT64B_CR, MCHP_PIT64B_CR_SWRST);
>> +	mchp_pit64b_write(data->base, MCHP_PIT64B_MR, mode);
>> +	mchp_pit64b_set_period(data->base, data->cycles);
>> +	if (irq_ena)
>> +		mchp_pit64b_write(data->base, MCHP_PIT64B_IER,
>> +				  MCHP_PIT64B_IER_PERIOD);
>> +	mchp_pit64b_write(data->base, MCHP_PIT64B_CR, MCHP_PIT64B_CR_START);
>> +}
>> +
>> +static u64 mchp_pit64b_read_clk(struct clocksource *cs)
>> +{
>> +	return mchp_pit64b_get_period(data.csd->cd->base);
>> +}
>> +
>> +static u64 mchp_sched_read_clk(void)
>> +{
>> +	return mchp_pit64b_get_period(data.csd->cd->base);
>> +}
>> +
>> +static struct clocksource mchp_pit64b_clksrc = {
>> +	.name = MCHP_PIT64B_NAME,
>> +	.mask = CLOCKSOURCE_MASK(64),
>> +	.flags = CLOCK_SOURCE_IS_CONTINUOUS,
>> +	.rating = 210,
>> +	.read = mchp_pit64b_read_clk,
>> +};
>> +
>> +static int mchp_pit64b_clkevt_shutdown(struct clock_event_device *cedev)
>> +{
>> +	mchp_pit64b_write(data.ced->cd->base, MCHP_PIT64B_CR,
>> +			  MCHP_PIT64B_CR_SWRST);
>> +
>> +	return 0;
>> +}
>> +
>> +static int mchp_pit64b_clkevt_set_periodic(struct clock_event_device *cedev)
>> +{
>> +	mchp_pit64b_reset(data.ced->cd, MCHP_PIT64B_MR_CONT, true);
>> +
>> +	return 0;
>> +}
>> +
>> +static int mchp_pit64b_clkevt_set_oneshot(struct clock_event_device *cedev)
>> +{
>> +	mchp_pit64b_reset(data.ced->cd, MCHP_PIT64B_MR_SMOD, true);
>> +
>> +	return 0;
>> +}
>> +
>> +static int mchp_pit64b_clkevt_set_next_event(unsigned long evt,
>> +					     struct clock_event_device *cedev)
>> +{
>> +	mchp_pit64b_set_period(data.ced->cd->base, evt);
>> +	mchp_pit64b_write(data.ced->cd->base, MCHP_PIT64B_CR,
>> +			  MCHP_PIT64B_CR_START);
>> +
>> +	return 0;
>> +}
>> +
>> +static void mchp_pit64b_clkevt_suspend(struct clock_event_device *cedev)
>> +{
>> +	mchp_pit64b_write(data.ced->cd->base, MCHP_PIT64B_CR,
>> +			  MCHP_PIT64B_CR_SWRST);
>> +	if (data.ced->cd->gclk)
>> +		clk_disable_unprepare(data.ced->cd->gclk);
>> +	clk_disable_unprepare(data.ced->cd->pclk);
>> +}
>> +
>> +static void mchp_pit64b_clkevt_resume(struct clock_event_device *cedev)
>> +{
>> +	u32 mode = MCHP_PIT64B_MR_SMOD;
>> +
>> +	clk_prepare_enable(data.ced->cd->pclk);
>> +	if (data.ced->cd->gclk)
>> +		clk_prepare_enable(data.ced->cd->gclk);
>> +
>> +	if (clockevent_state_periodic(data.ced->clkevt))
>> +		mode = MCHP_PIT64B_MR_CONT;
>> +
>> +	mchp_pit64b_reset(data.ced->cd, mode, true);
>> +}
>> +
>> +static struct clock_event_device mchp_pit64b_clkevt = {
>> +	.name = MCHP_PIT64B_NAME,
>> +	.features = CLOCK_EVT_FEAT_ONESHOT | CLOCK_EVT_FEAT_PERIODIC,
>> +	.rating = 150,
>> +	.set_state_shutdown = mchp_pit64b_clkevt_shutdown,
>> +	.set_state_periodic = mchp_pit64b_clkevt_set_periodic,
>> +	.set_state_oneshot = mchp_pit64b_clkevt_set_oneshot,
>> +	.set_next_event = mchp_pit64b_clkevt_set_next_event,
>> +	.suspend = mchp_pit64b_clkevt_suspend,
>> +	.resume = mchp_pit64b_clkevt_resume,
>> +};
>> +
>> +static irqreturn_t mchp_pit64b_interrupt(int irq, void *dev_id)
>> +{
>> +	struct mchp_pit64b_clkevt_data *irq_data = dev_id;
>> +
>> +	if (data.ced != irq_data)
>> +		return IRQ_NONE;
>> +
>> +	if (mchp_pit64b_read(irq_data->cd->base, MCHP_PIT64B_ISR) &
>> +	    MCHP_PIT64B_ISR_PERIOD) {
>> +		irq_data->clkevt->event_handler(irq_data->clkevt);
>> +		return IRQ_HANDLED;
>> +	}
>> +
>> +	return IRQ_NONE;
>> +}
>> +
>> +static int __init mchp_pit64b_pres_compute(u32 *pres, u32 clk_rate,
>> +					   u32 max_rate)
>> +{
>> +	u32 tmp;
>> +
>> +	for (*pres = 0; *pres < MCHP_PIT64B_PRES_MAX; (*pres)++) {
>> +		tmp = clk_rate / (*pres + 1);
>> +		if (tmp <= max_rate)
>> +			break;
>> +	}
>> +
>> +	if (*pres == MCHP_PIT64B_PRES_MAX)
>> +		return -EINVAL;
>> +
>> +	return 0;
>> +}
>> +
>> +static int __init mchp_pit64b_pres_prepare(struct mchp_pit64b_common_data *cd,
>> +					   unsigned long max_rate)
>> +{
>> +	unsigned long pclk_rate, diff = 0, best_diff = ULONG_MAX;
>> +	long gclk_round = 0;
>> +	u32 pres, best_pres;
>> +	int ret = 0;
>> +
>> +	pclk_rate = clk_get_rate(cd->pclk);
>> +	if (!pclk_rate)
>> +		return -EINVAL;
>> +
>> +	if (cd->gclk) {
>> +		gclk_round = clk_round_rate(cd->gclk, max_rate);
>> +		if (gclk_round < 0)
>> +			goto pclk;
>> +
>> +		if (pclk_rate / gclk_round < 3)
>> +			goto pclk;
>> +
>> +		ret = mchp_pit64b_pres_compute(&pres, gclk_round, max_rate);
>> +		if (ret)
>> +			best_diff = abs(gclk_round - max_rate);
>> +		else
>> +			best_diff = abs(gclk_round / (pres + 1) - max_rate);
>> +		best_pres = pres;
>> +	}
>> +
>> +pclk:
>> +	/* Check if requested rate could be obtained using PCLK. */
>> +	ret = mchp_pit64b_pres_compute(&pres, pclk_rate, max_rate);
>> +	if (ret)
>> +		diff = abs(pclk_rate - max_rate);
>> +	else
>> +		diff = abs(pclk_rate / (pres + 1) - max_rate);
>> +
>> +	if (best_diff > diff) {
>> +		/* Use PCLK. */
>> +		cd->gclk = NULL;
>> +		best_pres = pres;
>> +	} else {
>> +		clk_set_rate(cd->gclk, gclk_round);
>> +	}
>> +
>> +	cd->pres = best_pres;
>> +
>> +	pr_info("PIT64B: using clk=%s with prescaler %u, freq=%lu [Hz]\n",
>> +		cd->gclk ? "gclk" : "pclk", cd->pres,
>> +		cd->gclk ? gclk_round / (cd->pres + 1)
>> +			 : pclk_rate / (cd->pres + 1));
>> +
>> +	return 0;
>> +}
>> +
>> +static int __init mchp_pit64b_dt_init_clksrc(struct mchp_pit64b_common_data *cd)
>> +{
>> +	struct mchp_pit64b_clksrc_data *csd;
>> +	unsigned long clk_rate;
>> +	int ret;
>> +
>> +	csd = kzalloc(sizeof(*csd), GFP_KERNEL);
>> +	if (!csd)
>> +		return -ENOMEM;
>> +
>> +	csd->cd = cd;
>> +
>> +	if (csd->cd->gclk)
>> +		clk_rate = clk_get_rate(csd->cd->gclk);
>> +	else
>> +		clk_rate = clk_get_rate(csd->cd->pclk);
>> +
>> +	clk_rate = clk_rate / (cd->pres + 1);
>> +	csd->cd->cycles = ULLONG_MAX;
>> +	mchp_pit64b_reset(csd->cd, MCHP_PIT64B_MR_CONT, false);
>> +
>> +	data.csd = csd;
>> +
>> +	csd->clksrc = &mchp_pit64b_clksrc;
>> +
>> +	ret = clocksource_register_hz(csd->clksrc, clk_rate);
>> +	if (ret) {
>> +		pr_debug("clksrc: Failed to register PIT64B clocksource!\n");
>> +		goto free;
>> +	}
>> +
>> +	sched_clock_register(mchp_sched_read_clk, 64, clk_rate);
>> +
>> +	return 0;
>> +
>> +free:
>> +	kfree(csd);
>> +	data.csd = NULL;
>> +
>> +	return ret;
>> +}
>> +
>> +static int __init mchp_pit64b_dt_init_clkevt(struct mchp_pit64b_common_data *cd,
>> +					     u32 irq)
>> +{
>> +	struct mchp_pit64b_clkevt_data *ced;
>> +	unsigned long clk_rate;
>> +	int ret;
>> +
>> +	ced = kzalloc(sizeof(*ced), GFP_KERNEL);
>> +	if (!ced)
>> +		return -ENOMEM;
>> +
>> +	ced->cd = cd;
>> +
>> +	if (ced->cd->gclk)
>> +		clk_rate = clk_get_rate(ced->cd->gclk);
>> +	else
>> +		clk_rate = clk_get_rate(ced->cd->pclk);
>> +
>> +	clk_rate = clk_rate / (ced->cd->pres + 1);
>> +	ced->cd->cycles = DIV_ROUND_CLOSEST(clk_rate, HZ);
>> +
>> +	ret = request_irq(irq, mchp_pit64b_interrupt, IRQF_TIMER, "pit64b_tick",
>> +			  ced);
>> +	if (ret) {
>> +		pr_debug("clkevt: Failed to setup PIT64B IRQ\n");
>> +		goto free;
>> +	}
>> +
>> +	data.ced = ced;
>> +
>> +	/* Set up and register clockevents. */
>> +	ced->clkevt = &mchp_pit64b_clkevt;
>> +	ced->clkevt->cpumask = cpumask_of(0);
>> +	ced->clkevt->irq = irq;
>> +	clockevents_config_and_register(ced->clkevt, clk_rate, 1, ULONG_MAX);
>> +
>> +	return 0;
>> +
>> +free:
>> +	kfree(ced);
>> +	data.ced = NULL;
>> +
>> +	return ret;
>> +}
>> +
>> +static int __init mchp_pit64b_dt_init(struct device_node *node)
>> +{
>> +	struct mchp_pit64b_common_data *cd;
>> +	u32 irq, freq = MCHP_PIT64B_DEF_FREQ;
>> +	int ret;
>> +
>> +	if (data.csd && data.ced)
>> +		return -EBUSY;
>> +
>> +	cd = kzalloc(sizeof(*cd), GFP_KERNEL);
>> +	if (!cd)
>> +		return -ENOMEM;
>> +
>> +	cd->pclk = of_clk_get_by_name(node, "pclk");
>> +	if (IS_ERR(cd->pclk)) {
>> +		ret = PTR_ERR(cd->pclk);
>> +		goto free;
>> +	}
>> +
>> +	cd->gclk = of_clk_get_by_name(node, "gclk");
>> +	if (IS_ERR(cd->gclk))
>> +		cd->gclk = NULL;
>> +
>> +	ret = of_property_read_u32(node, "clock-frequency", &freq);
>> +	if (ret)
>> +		pr_debug("PIT64B: failed to read clock frequency. Using default!\n");
>> +
>> +	ret = mchp_pit64b_pres_prepare(cd, freq);
>> +	if (ret)
>> +		goto free;
>> +
>> +	cd->base = of_iomap(node, 0);
>> +	if (!cd->base) {
>> +		pr_debug("%s: Could not map PIT64B address!\n",
>> +			 MCHP_PIT64B_NAME);
>> +		ret = -ENXIO;
>> +		goto free;
>> +	}
>> +
>> +	ret = clk_prepare_enable(cd->pclk);
>> +	if (ret)
>> +		goto unmap;
>> +
>> +	if (cd->gclk) {
>> +		ret = clk_prepare_enable(cd->gclk);
>> +		if (ret)
>> +			goto pclk_unprepare;
>> +	}
>> +
>> +	if (!data.ced) {
>> +		irq = irq_of_parse_and_map(node, 0);
>> +		if (!irq) {
>> +			pr_debug("%s: Failed to get PIT64B clockevent IRQ!\n",
>> +				 MCHP_PIT64B_NAME);
>> +			ret = -ENODEV;
>> +			goto gclk_unprepare;
>> +		}
>> +		ret = mchp_pit64b_dt_init_clkevt(cd, irq);
>> +		if (ret)
>> +			goto irq_unmap;
>> +	} else {
>> +		ret = mchp_pit64b_dt_init_clksrc(cd);
>> +		if (ret)
>> +			goto gclk_unprepare;
>> +	}
>> +
>> +	return 0;
>> +
>> +irq_unmap:
>> +	irq_dispose_mapping(irq);
>> +gclk_unprepare:
>> +	if (cd->gclk)
>> +		clk_disable_unprepare(cd->gclk);
>> +pclk_unprepare:
>> +	clk_disable_unprepare(cd->pclk);
>> +unmap:
>> +	iounmap(cd->base);
>> +free:
>> +	kfree(cd);
>> +
>> +	return ret;
>> +}
>> +
>> +TIMER_OF_DECLARE(mchp_pit64b_clksrc, "microchip,sam9x60-pit64b",
>> +		 mchp_pit64b_dt_init);
>>
> 
> 

  reply	other threads:[~2019-04-08 11:48 UTC|newest]

Thread overview: 25+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-03-14 16:26 [PATCH 0/2] add Microchip PIT64B timer Claudiu.Beznea
2019-03-14 16:26 ` [PATCH 1/5] dt-bindings: arm: atmel: add bindings for PIT64B Claudiu.Beznea
2019-03-31  6:40   ` Rob Herring
2019-04-01  8:41   ` Nicolas.Ferre
2019-03-14 16:26 ` [PATCH 2/5] clocksource/drivers/timer-microchip-pit64b: add Microchip PIT64B support Claudiu.Beznea
2019-04-01  8:40   ` Nicolas.Ferre
2019-04-08  8:43   ` Daniel Lezcano
2019-04-08 11:48     ` Claudiu.Beznea [this message]
2019-04-08 12:11     ` Alexandre Belloni
2019-04-08 12:35       ` Daniel Lezcano
2019-04-08 12:42         ` Alexandre Belloni
2019-04-08 13:22           ` Daniel Lezcano
2019-04-08 14:01             ` Alexandre Belloni
2019-05-30  7:46       ` Claudiu.Beznea
2019-05-31 10:41         ` Daniel Lezcano
2019-06-13 14:12           ` Claudiu.Beznea
2019-06-20  8:53             ` Daniel Lezcano
2019-06-21 10:34               ` Claudiu.Beznea
2019-06-24  8:06                 ` Daniel Lezcano
2019-03-14 16:26 ` [PATCH 3/5] MAINTAINERS: change section name to be more generic Claudiu.Beznea
2019-04-01  8:41   ` Nicolas.Ferre
2019-03-14 16:26 ` [PATCH 4/5] MAINTAINERS: add myself as maintainer Claudiu.Beznea
2019-04-01  8:41   ` Nicolas.Ferre
2019-03-14 16:26 ` [PATCH 5/5] MAINTAINERS: add timer-microchip-pit64c.c Claudiu.Beznea
2019-04-01  8:41   ` Nicolas.Ferre

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=c2ae013a-0d7a-e415-f159-a1ba26c8257b@microchip.com \
    --to=claudiu.beznea@microchip.com \
    --cc=Ludovic.Desroches@microchip.com \
    --cc=Nicolas.Ferre@microchip.com \
    --cc=alexandre.belloni@bootlin.com \
    --cc=daniel.lezcano@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=robh+dt@kernel.org \
    --cc=tglx@linutronix.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).