From: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
To: bcm-kernel-feedback-list@broadcom.com,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org,
linux-rpi-kernel@lists.infradead.org
Cc: ariel.dalessandro@collabora.com, arnd@arndb.de,
f.fainelli@gmail.com, krzyszccf.kozlowski+dt@linaro.org,
nsaenz@kernel.org, olof@lixom.net, robh+dt@kernel.org,
soc@kernel.org, stefan.wahren@i2se.com,
william.zhang@broadcom.com
Subject: [PATCH] ARM: dts: Add Raspberry Pi Compute Module 4 CANOPi Board
Date: Fri, 16 Sep 2022 12:31:56 -0300 [thread overview]
Message-ID: <20220916153156.30412-1-ariel.dalessandro@collabora.com> (raw)
The Eclipse KUKSA CANOPi [0] is a baseboard for the Raspberry Compute
Module 4 (CM4). It contains a VIA VL805 4 Port USB controller and two
MCP251xFD based CAN-FD interfaces.
[0] https://github.com/boschresearch/kuksa.hardware
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/bcm2711-rpi-cm4-canopi.dts | 139 ++++++++++++++++++
arch/arm64/boot/dts/broadcom/Makefile | 1 +
.../dts/broadcom/bcm2711-rpi-cm4-canopi.dts | 2 +
4 files changed, 143 insertions(+)
create mode 100644 arch/arm/boot/dts/bcm2711-rpi-cm4-canopi.dts
create mode 100644 arch/arm64/boot/dts/broadcom/bcm2711-rpi-cm4-canopi.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 05d8aef6e5d2..8930ab2c132c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -98,6 +98,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
bcm2837-rpi-zero-2-w.dtb \
bcm2711-rpi-400.dtb \
bcm2711-rpi-4-b.dtb \
+ bcm2711-rpi-cm4-canopi.dtb \
bcm2711-rpi-cm4-io.dtb \
bcm2835-rpi-zero.dtb \
bcm2835-rpi-zero-w.dtb
diff --git a/arch/arm/boot/dts/bcm2711-rpi-cm4-canopi.dts b/arch/arm/boot/dts/bcm2711-rpi-cm4-canopi.dts
new file mode 100644
index 000000000000..52ec5908883c
--- /dev/null
+++ b/arch/arm/boot/dts/bcm2711-rpi-cm4-canopi.dts
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2711-rpi-cm4.dtsi"
+
+/ {
+ model = "Raspberry Pi Compute Module 4 CANOPi Board";
+
+ clocks {
+ clk_mcp251xfd_osc: mcp251xfd-osc {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <20000000>;
+ };
+ };
+
+ leds {
+ led-act {
+ gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-pwr {
+ label = "PWR";
+ gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ linux,default-trigger = "default-on";
+ };
+ };
+};
+
+&ddc0 {
+ status = "okay";
+};
+
+&ddc1 {
+ status = "okay";
+};
+
+&hdmi0 {
+ status = "okay";
+};
+
+&hdmi1 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_gpio44>;
+ status = "okay";
+ clock-frequency = <100000>;
+
+ pcf85063a@51 {
+ compatible = "nxp,pcf85063a";
+ reg = <0x51>;
+ };
+};
+
+&pcie0 {
+ pci@0,0 {
+ device_type = "pci";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ reg = <0 0 0 0 0>;
+
+ usb@0,0 {
+ reg = <0 0 0 0 0>;
+ resets = <&reset RASPBERRYPI_FIRMWARE_RESET_ID_USB>;
+ };
+ };
+};
+
+&pixelvalve0 {
+ status = "okay";
+};
+
+&pixelvalve1 {
+ status = "okay";
+};
+
+&pixelvalve2 {
+ status = "okay";
+};
+
+&pixelvalve4 {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_gpio7>;
+ cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+ dmas = <&dma 6>, <&dma 7>;
+ dma-names = "tx", "rx";
+
+ mcp251xfd0: mcp251xfd@0 {
+ compatible = "microchip,mcp251xfd";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcp251xfd0_pins>;
+ spi-max-frequency = <20000000>;
+ interrupt-parent = <&gpio>;
+ interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clk_mcp251xfd_osc>;
+ };
+
+ mcp251xfd1: mcp251xfd@1 {
+ compatible = "microchip,mcp251xfd";
+ reg = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcp251xfd1_pins>;
+ spi-max-frequency = <20000000>;
+ interrupt-parent = <&gpio>;
+ interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clk_mcp251xfd_osc>;
+ };
+};
+
+&gpio {
+ mcp251xfd0_pins: mcp251xfd0_pins {
+ brcm,pins = <27>;
+ brcm,function = <BCM2835_FSEL_GPIO_IN>;
+ };
+
+ mcp251xfd1_pins: mcp251xfd1_pins {
+ brcm,pins = <22>;
+ brcm,function = <BCM2835_FSEL_GPIO_IN>;
+ };
+};
+
+&vc4 {
+ status = "okay";
+};
+
+&vec {
+ status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/broadcom/Makefile b/arch/arm64/boot/dts/broadcom/Makefile
index e8584d3b698f..7cd88b8c0345 100644
--- a/arch/arm64/boot/dts/broadcom/Makefile
+++ b/arch/arm64/boot/dts/broadcom/Makefile
@@ -1,6 +1,7 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_BCM2835) += bcm2711-rpi-400.dtb \
bcm2711-rpi-4-b.dtb \
+ bcm2711-rpi-cm4-canopi.dtb \
bcm2711-rpi-cm4-io.dtb \
bcm2837-rpi-3-a-plus.dtb \
bcm2837-rpi-3-b.dtb \
diff --git a/arch/arm64/boot/dts/broadcom/bcm2711-rpi-cm4-canopi.dts b/arch/arm64/boot/dts/broadcom/bcm2711-rpi-cm4-canopi.dts
new file mode 100644
index 000000000000..e9369aa0eb39
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcm2711-rpi-cm4-canopi.dts
@@ -0,0 +1,2 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "arm/bcm2711-rpi-cm4-canopi.dts"
--
2.37.2
next reply other threads:[~2022-09-16 15:32 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-09-16 15:31 Ariel D'Alessandro [this message]
2022-09-17 10:18 ` [PATCH] ARM: dts: Add Raspberry Pi Compute Module 4 CANOPi Board Stefan Wahren
2022-09-19 7:47 ` Alexander Dahl
2022-09-19 11:18 ` Stefan Wahren
2022-09-20 8:31 ` Alexander Dahl
2022-09-20 15:41 ` Stefan Wahren
2022-09-20 9:51 ` Krzysztof Kozlowski
2022-10-20 12:16 ` Pavel Machek
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220916153156.30412-1-ariel.dalessandro@collabora.com \
--to=ariel.dalessandro@collabora.com \
--cc=arnd@arndb.de \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=devicetree@vger.kernel.org \
--cc=f.fainelli@gmail.com \
--cc=krzyszccf.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rpi-kernel@lists.infradead.org \
--cc=nsaenz@kernel.org \
--cc=olof@lixom.net \
--cc=robh+dt@kernel.org \
--cc=soc@kernel.org \
--cc=stefan.wahren@i2se.com \
--cc=william.zhang@broadcom.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).