u-boot.lists.denx.de archive mirror
 help / color / mirror / Atom feed
From: "Ramon Fried" <rfried.dev@gmail.com>
To: "Daniil Stas" <daniil.stas@posteo.net>, <u-boot@lists.denx.de>
Cc: "Joe Hershberger" <joe.hershberger@ni.com>,
	"Patrick Delaunay" <patrick.delaunay@foss.st.com>,
	"Patrice Chotard" <patrice.chotard@foss.st.com>
Subject: Re: [PATCH] net: dwc_eth_qos: Fix needless phy auto-negotiation restarts
Date: Sat, 12 Jun 2021 21:36:42 +0300	[thread overview]
Message-ID: <CC1UVF5KX51U.T5ALTMCV25D8@stdcall-pc> (raw)
In-Reply-To: <20210523222449.1495352-1-daniil.stas@posteo.net>

On Mon May 24, 2021 at 1:24 AM IDT, Daniil Stas wrote:
> Disabling clk_ck clock leads to link up status loss in phy, which
> leads to auto-negotiation restart before each network command
> execution.
>
> This issue is especially big for PXE boot protocol because of
> auto-negotiation restarts before each configuration filename trial.
>
> To avoid this issue don't disable clk_ck clock after it was enabled.
>
> Signed-off-by: Daniil Stas <daniil.stas@posteo.net>
> Cc: Ramon Fried <rfried.dev@gmail.com>
> Cc: Joe Hershberger <joe.hershberger@ni.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> ---
> drivers/net/dwc_eth_qos.c | 6 +++---
> 1 file changed, 3 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/net/dwc_eth_qos.c b/drivers/net/dwc_eth_qos.c
> index e8242ca4e1..2f088c758f 100644
> --- a/drivers/net/dwc_eth_qos.c
> +++ b/drivers/net/dwc_eth_qos.c
> @@ -321,6 +321,7 @@ struct eqos_priv {
> void *rx_pkt;
> bool started;
> bool reg_access_ok;
> + bool clk_ck_enabled;
> };
>  
> /*
> @@ -591,12 +592,13 @@ static int eqos_start_clks_stm32(struct udevice
> *dev)
> goto err_disable_clk_rx;
> }
>  
> - if (clk_valid(&eqos->clk_ck)) {
> + if (clk_valid(&eqos->clk_ck) && !eqos->clk_ck_enabled) {
> ret = clk_enable(&eqos->clk_ck);
> if (ret < 0) {
> pr_err("clk_enable(clk_ck) failed: %d", ret);
> goto err_disable_clk_tx;
> }
> + eqos->clk_ck_enabled = true;
> }
> #endif
>  
> @@ -648,8 +650,6 @@ static void eqos_stop_clks_stm32(struct udevice
> *dev)
> clk_disable(&eqos->clk_tx);
> clk_disable(&eqos->clk_rx);
> clk_disable(&eqos->clk_master_bus);
> - if (clk_valid(&eqos->clk_ck))
> - clk_disable(&eqos->clk_ck);
> #endif
>  
> debug("%s: OK\n", __func__);
> --
> 2.31.0

Applied to u-boot-net/master, thanks!

Best regards,
Ramon Fried

      parent reply	other threads:[~2021-06-12 18:36 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-05-23 22:24 [PATCH] net: dwc_eth_qos: Fix needless phy auto-negotiation restarts Daniil Stas
2021-05-23 22:24 ` [PATCH] spi: stm32_qspi: Fix short data write operation Daniil Stas
2021-05-24  7:40   ` Patrice CHOTARD
2021-05-24 12:53     ` Daniil Stas
2021-05-25 16:02       ` Patrice CHOTARD
2021-06-18  8:01         ` Patrice CHOTARD
2021-06-01 15:31   ` Patrick DELAUNAY
2021-05-24  8:30 ` [PATCH] net: dwc_eth_qos: Fix needless phy auto-negotiation restarts Patrice CHOTARD
2021-05-25  6:53 ` Ramon Fried
2021-06-01 15:26 ` Patrick DELAUNAY
2021-06-12 18:36 ` Ramon Fried [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=CC1UVF5KX51U.T5ALTMCV25D8@stdcall-pc \
    --to=rfried.dev@gmail.com \
    --cc=daniil.stas@posteo.net \
    --cc=joe.hershberger@ni.com \
    --cc=patrice.chotard@foss.st.com \
    --cc=patrick.delaunay@foss.st.com \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).