From: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH] ARM: Kirkwood: Add support for OpenRD-Client & OpenRD-Ultimate
Date: Thu, 10 Jun 2010 14:42:24 +0530 [thread overview]
Message-ID: <1276161144-20204-1-git-send-email-tanmay.upadhyay@einfochips.com> (raw)
In-Reply-To: <no>
This patch modifies existing OpenRD-Base support to deal with all
the three OpenRD boards (OpenRD-Base, OpenRD-Client & OpenRD-Ultimate).
Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
---
Makefile | 9 +-
arch/arm/include/asm/mach-types.h | 13 ++
board/Marvell/openrd/Makefile | 65 +++++++++
board/Marvell/openrd/config.mk | 33 +++++
board/Marvell/openrd/kwbimage.cfg | 168 +++++++++++++++++++++++
board/Marvell/openrd/openrd.c | 180 +++++++++++++++++++++++++
board/Marvell/openrd/openrd.h | 67 ++++++++++
board/Marvell/openrd_base/Makefile | 56 --------
board/Marvell/openrd_base/config.mk | 33 -----
board/Marvell/openrd_base/kwbimage.cfg | 168 -----------------------
board/Marvell/openrd_base/openrd_base.c | 160 ----------------------
board/Marvell/openrd_base/openrd_base.h | 46 -------
include/configs/openrd_client.h | 219 +++++++++++++++++++++++++++++++
include/configs/openrd_ultimate.h | 219 +++++++++++++++++++++++++++++++
14 files changed, 972 insertions(+), 464 deletions(-)
create mode 100644 board/Marvell/openrd/Makefile
create mode 100644 board/Marvell/openrd/config.mk
create mode 100644 board/Marvell/openrd/kwbimage.cfg
create mode 100644 board/Marvell/openrd/openrd.c
create mode 100644 board/Marvell/openrd/openrd.h
delete mode 100644 board/Marvell/openrd_base/Makefile
delete mode 100644 board/Marvell/openrd_base/config.mk
delete mode 100644 board/Marvell/openrd_base/kwbimage.cfg
delete mode 100644 board/Marvell/openrd_base/openrd_base.c
delete mode 100644 board/Marvell/openrd_base/openrd_base.h
create mode 100644 include/configs/openrd_client.h
create mode 100644 include/configs/openrd_ultimate.h
diff --git a/Makefile b/Makefile
index c26e491..f12214b 100644
--- a/Makefile
+++ b/Makefile
@@ -3007,8 +3007,15 @@ omap1610h2_cs_autoboot_config: unconfig
omap5912osk_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm926ejs omap5912osk ti omap
+openrd_ultimate_config \
+openrd_client_config \
openrd_base_config: unconfig
- @$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+ @$(MKCONFIG) $(@:_config=) arm arm926ejs openrd Marvell kirkwood
+ifneq ($(SRCTREE),$(OBJTREE))
+ @echo "VARIANT= $(@:_config=)" >> $(OBJTREE)/include/config.mk
+else
+ @echo "VARIANT= $(@:_config=)" >> ./include/config.mk
+endif
xtract_omap730p2 = $(subst _cs0boot,,$(subst _cs3boot,, $(subst _config,,$1)))
diff --git a/arch/arm/include/asm/mach-types.h b/arch/arm/include/asm/mach-types.h
index 940d814..19114b0 100644
--- a/arch/arm/include/asm/mach-types.h
+++ b/arch/arm/include/asm/mach-types.h
@@ -2862,6 +2862,7 @@ extern unsigned int __machine_arch_type;
#define MACH_TYPE_MATRIX518 2879
#define MACH_TYPE_TINY_GURNARD 2880
#define MACH_TYPE_SPEAR1310 2881
+#define MACH_TYPE_OPENRD_ULTIMATE 2884
#ifdef CONFIG_ARCH_EBSA110
# ifdef machine_arch_type
@@ -37063,6 +37064,18 @@ extern unsigned int __machine_arch_type;
# define machine_is_spear1310() (0)
#endif
+#ifdef CONFIG_MACH_OPENRD_ULTIMATE
+# ifdef machine_arch_type
+# undef machine_arch_type
+# define machine_arch_type __machine_arch_type
+# else
+# define machine_arch_type MACH_TYPE_OPENRD_ULTIMATE
+# endif
+# define machine_is_openrd_ultimate() (machine_arch_type == MACH_TYPE_OPENRD_ULTIMATE)
+#else
+# define machine_is_openrd_ultimate() (0)
+#endif
+
/*
* These have not yet been registered
*/
diff --git a/board/Marvell/openrd/Makefile b/board/Marvell/openrd/Makefile
new file mode 100644
index 0000000..96328e7
--- /dev/null
+++ b/board/Marvell/openrd/Makefile
@@ -0,0 +1,65 @@
+#
+# (C) Copyright 2009
+# Net Insight <www.netinsight.net>
+# Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+#
+# Based on sheevaplug:
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+# Get the board variant (base/client/ultimate) from the .mk file
+ifneq ($(SRCTREE),$(OBJTREE))
+include $(OBJTREE)/include/config.mk
+else
+include $(TOPDIR)/include/config.mk
+endif
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := openrd.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+CFLAGS += -D$(VARIANT)
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/Marvell/openrd/config.mk b/board/Marvell/openrd/config.mk
new file mode 100644
index 0000000..8ae355e
--- /dev/null
+++ b/board/Marvell/openrd/config.mk
@@ -0,0 +1,33 @@
+#
+# (C) Copyright 2009
+# Net Insight <www.netinsight.net>
+# Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+#
+# Based on sheevaplug:
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00600000
+
+# Kirkwood Boot Image configuration file
+KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
diff --git a/board/Marvell/openrd/kwbimage.cfg b/board/Marvell/openrd/kwbimage.cfg
new file mode 100644
index 0000000..757eb28
--- /dev/null
+++ b/board/Marvell/openrd/kwbimage.cfg
@@ -0,0 +1,168 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM nand
+NAND_ECC_MODE default
+NAND_PAGE_SIZE 0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b1b9b
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000c30 # DDR Configuration register
+# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
+# bit23-14: zero
+# bit24: 1= enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: zero
+# bit31-30: 01
+
+DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
+# bit 4: 0=addr/cmd in smame cycle
+# bit 5: 0=clk is driven during self refresh, we don't care for APX
+# bit 6: 0=use recommended falling edge of clk for addr/cmd
+# bit14: 0=input buffer always powered up
+# bit18: 1=cpu lock transaction enabled
+# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31: 0=no additional STARTBURST delay
+
+DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
+# bit3-0: TRAS lsbs
+# bit7-4: TRCD
+# bit11- 8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20: TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
+# bit6-0: TRFC
+# bit8-7: TR2R
+# bit10-9: TR2W
+# bit12-11: TW2W
+# bit31-13: zero required
+
+DATA 0xFFD01410 0x000000cc # DDR Address Control
+# bit1-0: 00, Cs0width=x8
+# bit3-2: 11, Cs0size=1Gb
+# bit5-4: 00, Cs1width=x8
+# bit7-6: 11, Cs1size=1Gb
+# bit9-8: 00, Cs2width=nonexistent
+# bit11-10: 00, Cs2size =nonexistent
+# bit13-12: 00, Cs3width=nonexistent
+# bit15-14: 00, Cs3size =nonexistent
+# bit16: 0, Cs0AddrSel
+# bit17: 0, Cs1AddrSel
+# bit18: 0, Cs2AddrSel
+# bit19: 0, Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
+# bit0: 0, OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000 # DDR Operation
+# bit3-0: 0x0, DDR cmd
+# bit31-4: 0 required
+
+DATA 0xFFD0141C 0x00000C52 # DDR Mode
+# bit2-0: 2, BurstLen=2 required
+# bit3: 0, BurstType=0 required
+# bit6-4: 4, CL=5
+# bit7: 0, TestMode=0 normal
+# bit8: 0, DLL reset=0 normal
+# bit11-9: 6, auto-precharge write recovery ????????????
+# bit12: 0, PD must be zero
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000042 # DDR Extended Mode
+# bit0: 0, DDR DLL enabled
+# bit1: 1, DDR drive strength reduced
+# bit2: 0, DDR ODT control lsd (disabled)
+# bit5-3: 000, required
+# bit6: 1, DDR ODT control msb, (disabled)
+# bit9-7: 000, required
+# bit10: 0, differential DQS enabled
+# bit11: 0, required
+# bit12: 0, DDR output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
+# bit2-0: 111, required
+# bit3 : 1 , MBUS Burst Chop disabled
+# bit6-4: 111, required
+# bit7 : 0
+# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9 : 0 , no half clock cycle addition to dataout
+# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 1111 required
+# bit31-16: 0 required
+
+DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
+DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
+DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
+# bit0: 1, Window enabled
+# bit1: 0, Write Protect disabled
+# bit3-2: 00, CS0 hit selected
+# bit23-4: ones, required
+# bit31-24: 0x0F, Size (i.e. 256MB)
+
+DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
+DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1
+
+DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low)
+# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1
+# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0
+# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1.
+# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0.
+DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
+
+DATA 0xFFD0149C 0x0000E40f # CPU ODT Control
+# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3
+# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm
+# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
+# bit14: 1, M_STARTBURST_IN ODT: Enabled
+# bit15: 1, DDR IO ODT Unit: Use ODT block
+DATA 0xFFD01480 0x00000001 # DDR Initialization Control
+#bit0=1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0
diff --git a/board/Marvell/openrd/openrd.c b/board/Marvell/openrd/openrd.c
new file mode 100644
index 0000000..0630947
--- /dev/null
+++ b/board/Marvell/openrd/openrd.c
@@ -0,0 +1,180 @@
+/*
+ * Modified Simon's work to deal with all the three variants of
+ * OpenRD boards (OpenRD-Base, OpenRD-Client & OpenRD-Ultimate)
+ *
+ * eInfochips <www.einfochips.com>
+ * Modified-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
+ *
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+ *
+ * Based on sheevaplug.c:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "openrd.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ kw_config_gpio(OPENRD_OE_VAL_LOW,
+ OPENRD_OE_VAL_HIGH,
+ OPENRD_OE_LOW, OPENRD_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_TW_SDA,
+ MPP9_TW_SCK,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_SD_CLK,
+ MPP13_SD_CMD, /* Alt UART1_TXD */
+ MPP14_SD_D0, /* Alt UART1_RXD */
+ MPP15_SD_D1,
+ MPP16_SD_D2,
+ MPP17_SD_D3,
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GE1_0,
+ MPP21_GE1_1,
+ MPP22_GE1_2,
+ MPP23_GE1_3,
+ MPP24_GE1_4,
+ MPP25_GE1_5,
+ MPP26_GE1_6,
+ MPP27_GE1_7,
+ MPP28_GPIO,
+ MPP29_TSMP9,
+ MPP30_GE1_10,
+ MPP31_GE1_11,
+ MPP32_GE1_12,
+ MPP33_GE1_13,
+ MPP34_GPIO, /* UART1 / SD sel */
+ MPP35_TDM_CH0_TX_QL,
+ MPP36_TDM_SPI_CS1,
+ MPP37_TDM_CH2_TX_QL,
+ MPP38_TDM_CH2_RX_QL,
+ MPP39_AUDIO_I2SBCLK,
+ MPP40_AUDIO_I2SDO,
+ MPP41_AUDIO_I2SLRC,
+ MPP42_AUDIO_I2SMCLK,
+ MPP43_AUDIO_I2SDI,
+ MPP44_AUDIO_EXTCLK,
+ MPP45_TDM_PCLK,
+ MPP46_TDM_FS,
+ MPP47_TDM_DRX,
+ MPP48_TDM_DTX,
+ MPP49_TDM_CH0_RX_QL,
+ 0
+ };
+
+ kirkwood_mpp_conf(kwmpp_config);
+
+ /*
+ * arch number of board
+ */
+ gd->bd->bi_arch_number = MACH_TYPE_OPENRD;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+ return 0;
+}
+
+int dram_init(void)
+{
+ int i;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ gd->bd->bi_dram[i].start = kw_sdram_bar(i);
+ gd->bd->bi_dram[i].size = kw_sdram_bs(i);
+ }
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1116/MV88E1121 PHY */
+void mv_phy_init(char *name)
+{
+ u16 reg;
+ u16 devadr;
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* command to read PHY dev address */
+ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+ printf("Err..%s could not read PHY dev address\n", __func__);
+ return;
+ }
+
+ /*
+ * Enable RGMII delay on Tx and Rx for CPU port
+ * Ref: sec 4.7.2 of chip datasheet
+ */
+ miiphy_write(name, devadr, PGADR_REG, 2);
+ miiphy_read(name, devadr, MAC_CTRL_REG, ®);
+ reg |= (RGMII_RXTM_CTRL | RGMII_TXTM_CTRL);
+ miiphy_write(name, devadr, MAC_CTRL_REG, reg);
+ miiphy_write(name, devadr, PGADR_REG, 0);
+
+ /* reset the phy */
+ if (!miiphy_reset(name, devadr))
+ printf("%s Initialized on %s\n", PHY_NO, name);
+}
+
+void reset_phy(void)
+{
+ mv_phy_init("egiga0");
+
+#ifdef openrd_client
+ /* Kirkwood ethernet driver is written with the assumption that in case
+ * of multiple PHYs, their addresses are consecutive. But unfortunately
+ * in case of OpenRD-Client, PHY addresses are not consecutive.*/
+ miiphy_write("egiga1", 0xEE, 0xEE, 24);
+#endif
+
+#if defined(openrd_client) || defined(openrd_ultimate)
+ /* configure and initialize both PHY's */
+ mv_phy_init("egiga1");
+#endif
+}
+#endif /* CONFIG_RESET_PHY_R */
diff --git a/board/Marvell/openrd/openrd.h b/board/Marvell/openrd/openrd.h
new file mode 100644
index 0000000..8b0cbf8
--- /dev/null
+++ b/board/Marvell/openrd/openrd.h
@@ -0,0 +1,67 @@
+/*
+ * Modified Simon's work to deal with all the three variants of
+ * OpenRD boards (OpenRD-Base, OpenRD-Client & OpenRD-Ultimate)
+ *
+ * eInfochips <www.einfochips.com>
+ * Modified-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
+ *
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+ *
+ * Based on sheevaplug.h:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __OPENRD_H
+#define __OPENRD_H
+
+#define OPENRD_OE_LOW (~(1<<28)) /* RS232 / RS485 */
+#define OPENRD_OE_HIGH (~(1<<2)) /* SD / UART1 */
+#define OPENRD_OE_VAL_LOW (0) /* Sel RS232 */
+#define OPENRD_OE_VAL_HIGH (1 << 2) /* Sel SD */
+
+/* PHY related */
+#define MAC_CTRL_REG 21
+#define PGADR_REG 22
+#define RGMII_TXTM_CTRL (1 << 4)
+#define RGMII_RXTM_CTRL (1 << 5)
+
+#ifdef openrd_base
+#define MACH_TYPE_OPENRD MACH_TYPE_OPENRD_BASE
+#endif
+
+#ifdef openrd_client
+#define MACH_TYPE_OPENRD MACH_TYPE_OPENRD_CLIENT
+#endif
+
+#ifdef openrd_ultimate
+#define MACH_TYPE_OPENRD MACH_TYPE_OPENRD_ULTIMATE
+/* OpenRD-Ultimate uses 88E1121 PHY */
+#define PHY_NO "88E1121"
+#else
+/* OpenRD-Base & OpenRD-Client uses 88E1116 PHY */
+#define PHY_NO "88E1116"
+#endif
+
+#endif /* __OPENRD_H */
diff --git a/board/Marvell/openrd_base/Makefile b/board/Marvell/openrd_base/Makefile
deleted file mode 100644
index 3ef0b9b..0000000
--- a/board/Marvell/openrd_base/Makefile
+++ /dev/null
@@ -1,56 +0,0 @@
-#
-# (C) Copyright 2009
-# Net Insight <www.netinsight.net>
-# Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
-#
-# Based on sheevaplug:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
-# MA 02110-1301 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB = $(obj)lib$(BOARD).a
-
-COBJS := openrd_base.o
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
-
-$(LIB): $(obj).depend $(OBJS) $(SOBJS)
- $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
-
-clean:
- rm -f $(SOBJS) $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak .depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/Marvell/openrd_base/config.mk b/board/Marvell/openrd_base/config.mk
deleted file mode 100644
index 8ae355e..0000000
--- a/board/Marvell/openrd_base/config.mk
+++ /dev/null
@@ -1,33 +0,0 @@
-#
-# (C) Copyright 2009
-# Net Insight <www.netinsight.net>
-# Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
-#
-# Based on sheevaplug:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
-# MA 02110-1301 USA
-#
-
-TEXT_BASE = 0x00600000
-
-# Kirkwood Boot Image configuration file
-KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
diff --git a/board/Marvell/openrd_base/kwbimage.cfg b/board/Marvell/openrd_base/kwbimage.cfg
deleted file mode 100644
index 757eb28..0000000
--- a/board/Marvell/openrd_base/kwbimage.cfg
+++ /dev/null
@@ -1,168 +0,0 @@
-#
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
-# MA 02110-1301 USA
-#
-# Refer docs/README.kwimage for more details about how-to configure
-# and create kirkwood boot image
-#
-
-# Boot Media configurations
-BOOT_FROM nand
-NAND_ECC_MODE default
-NAND_PAGE_SIZE 0x0800
-
-# SOC registers configuration using bootrom header extension
-# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
-
-# Configure RGMII-0 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1b1b1b9b
-
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
-DATA 0xFFD01400 0x43000c30 # DDR Configuration register
-# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
-# bit23-14: zero
-# bit24: 1= enable exit self refresh mode on DDR access
-# bit25: 1 required
-# bit29-26: zero
-# bit31-30: 01
-
-DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
-# bit 4: 0=addr/cmd in smame cycle
-# bit 5: 0=clk is driven during self refresh, we don't care for APX
-# bit 6: 0=use recommended falling edge of clk for addr/cmd
-# bit14: 0=input buffer always powered up
-# bit18: 1=cpu lock transaction enabled
-# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
-# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
-# bit30-28: 3 required
-# bit31: 0=no additional STARTBURST delay
-
-DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
-# bit3-0: TRAS lsbs
-# bit7-4: TRCD
-# bit11- 8: TRP
-# bit15-12: TWR
-# bit19-16: TWTR
-# bit20: TRAS msb
-# bit23-21: 0x0
-# bit27-24: TRRD
-# bit31-28: TRTP
-
-DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
-# bit6-0: TRFC
-# bit8-7: TR2R
-# bit10-9: TR2W
-# bit12-11: TW2W
-# bit31-13: zero required
-
-DATA 0xFFD01410 0x000000cc # DDR Address Control
-# bit1-0: 00, Cs0width=x8
-# bit3-2: 11, Cs0size=1Gb
-# bit5-4: 00, Cs1width=x8
-# bit7-6: 11, Cs1size=1Gb
-# bit9-8: 00, Cs2width=nonexistent
-# bit11-10: 00, Cs2size =nonexistent
-# bit13-12: 00, Cs3width=nonexistent
-# bit15-14: 00, Cs3size =nonexistent
-# bit16: 0, Cs0AddrSel
-# bit17: 0, Cs1AddrSel
-# bit18: 0, Cs2AddrSel
-# bit19: 0, Cs3AddrSel
-# bit31-20: 0 required
-
-DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
-# bit0: 0, OpenPage enabled
-# bit31-1: 0 required
-
-DATA 0xFFD01418 0x00000000 # DDR Operation
-# bit3-0: 0x0, DDR cmd
-# bit31-4: 0 required
-
-DATA 0xFFD0141C 0x00000C52 # DDR Mode
-# bit2-0: 2, BurstLen=2 required
-# bit3: 0, BurstType=0 required
-# bit6-4: 4, CL=5
-# bit7: 0, TestMode=0 normal
-# bit8: 0, DLL reset=0 normal
-# bit11-9: 6, auto-precharge write recovery ????????????
-# bit12: 0, PD must be zero
-# bit31-13: 0 required
-
-DATA 0xFFD01420 0x00000042 # DDR Extended Mode
-# bit0: 0, DDR DLL enabled
-# bit1: 1, DDR drive strength reduced
-# bit2: 0, DDR ODT control lsd (disabled)
-# bit5-3: 000, required
-# bit6: 1, DDR ODT control msb, (disabled)
-# bit9-7: 000, required
-# bit10: 0, differential DQS enabled
-# bit11: 0, required
-# bit12: 0, DDR output buffer enabled
-# bit31-13: 0 required
-
-DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
-# bit2-0: 111, required
-# bit3 : 1 , MBUS Burst Chop disabled
-# bit6-4: 111, required
-# bit7 : 0
-# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
-# bit9 : 0 , no half clock cycle addition to dataout
-# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
-# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
-# bit15-12: 1111 required
-# bit31-16: 0 required
-
-DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
-DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
-
-DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
-DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
-# bit0: 1, Window enabled
-# bit1: 0, Write Protect disabled
-# bit3-2: 00, CS0 hit selected
-# bit23-4: ones, required
-# bit31-24: 0x0F, Size (i.e. 256MB)
-
-DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
-DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1
-
-DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
-DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
-
-DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low)
-# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1
-# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0
-# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1.
-# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0.
-DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
-
-DATA 0xFFD0149C 0x0000E40f # CPU ODT Control
-# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3
-# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm
-# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
-# bit14: 1, M_STARTBURST_IN ODT: Enabled
-# bit15: 1, DDR IO ODT Unit: Use ODT block
-DATA 0xFFD01480 0x00000001 # DDR Initialization Control
-#bit0=1, enable DDR init upon this register write
-
-# End of Header extension
-DATA 0x0 0x0
diff --git a/board/Marvell/openrd_base/openrd_base.c b/board/Marvell/openrd_base/openrd_base.c
deleted file mode 100644
index c00a08a..0000000
--- a/board/Marvell/openrd_base/openrd_base.c
+++ /dev/null
@@ -1,160 +0,0 @@
-/*
- * (C) Copyright 2009
- * Net Insight <www.netinsight.net>
- * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
- *
- * Based on sheevaplug.c:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301 USA
- */
-
-#include <common.h>
-#include <miiphy.h>
-#include <asm/arch/kirkwood.h>
-#include <asm/arch/mpp.h>
-#include "openrd_base.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_init(void)
-{
- /*
- * default gpio configuration
- * There are maximum 64 gpios controlled through 2 sets of registers
- * the below configuration configures mainly initial LED status
- */
- kw_config_gpio(OPENRD_OE_VAL_LOW,
- OPENRD_OE_VAL_HIGH,
- OPENRD_OE_LOW, OPENRD_OE_HIGH);
-
- /* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
- MPP0_NF_IO2,
- MPP1_NF_IO3,
- MPP2_NF_IO4,
- MPP3_NF_IO5,
- MPP4_NF_IO6,
- MPP5_NF_IO7,
- MPP6_SYSRST_OUTn,
- MPP7_GPO,
- MPP8_TW_SDA,
- MPP9_TW_SCK,
- MPP10_UART0_TXD,
- MPP11_UART0_RXD,
- MPP12_SD_CLK,
- MPP13_SD_CMD, /* Alt UART1_TXD */
- MPP14_SD_D0, /* Alt UART1_RXD */
- MPP15_SD_D1,
- MPP16_SD_D2,
- MPP17_SD_D3,
- MPP18_NF_IO0,
- MPP19_NF_IO1,
- MPP20_GE1_0,
- MPP21_GE1_1,
- MPP22_GE1_2,
- MPP23_GE1_3,
- MPP24_GE1_4,
- MPP25_GE1_5,
- MPP26_GE1_6,
- MPP27_GE1_7,
- MPP28_GPIO,
- MPP29_TSMP9,
- MPP30_GE1_10,
- MPP31_GE1_11,
- MPP32_GE1_12,
- MPP33_GE1_13,
- MPP34_GPIO, /* UART1 / SD sel */
- MPP35_TDM_CH0_TX_QL,
- MPP36_TDM_SPI_CS1,
- MPP37_TDM_CH2_TX_QL,
- MPP38_TDM_CH2_RX_QL,
- MPP39_AUDIO_I2SBCLK,
- MPP40_AUDIO_I2SDO,
- MPP41_AUDIO_I2SLRC,
- MPP42_AUDIO_I2SMCLK,
- MPP43_AUDIO_I2SDI,
- MPP44_AUDIO_EXTCLK,
- MPP45_TDM_PCLK,
- MPP46_TDM_FS,
- MPP47_TDM_DRX,
- MPP48_TDM_DTX,
- MPP49_TDM_CH0_RX_QL,
- 0
- };
-
- kirkwood_mpp_conf(kwmpp_config);
-
- /*
- * arch number of board
- */
- gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE;
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
- return 0;
-}
-
-int dram_init(void)
-{
- int i;
-
- for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
- gd->bd->bi_dram[i].start = kw_sdram_bar(i);
- gd->bd->bi_dram[i].size = kw_sdram_bs(i);
- }
- return 0;
-}
-
-#ifdef CONFIG_RESET_PHY_R
-/* Configure and enable MV88E1116 PHY */
-void reset_phy(void)
-{
- u16 reg;
- u16 devadr;
- char *name = "egiga0";
-
- if (miiphy_set_current_dev(name))
- return;
-
- /* command to read PHY dev address */
- if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
- printf("Err..%s could not read PHY dev address\n",
- __FUNCTION__);
- return;
- }
-
- /*
- * Enable RGMII delay on Tx and Rx for CPU port
- * Ref: sec 4.7.2 of chip datasheet
- */
- miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
- miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
- reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
- miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
- miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
-
- /* reset the phy */
- miiphy_reset(name, devadr);
-
- printf("88E1116 Initialized on %s\n", name);
-}
-#endif /* CONFIG_RESET_PHY_R */
diff --git a/board/Marvell/openrd_base/openrd_base.h b/board/Marvell/openrd_base/openrd_base.h
deleted file mode 100644
index f3daf17..0000000
--- a/board/Marvell/openrd_base/openrd_base.h
+++ /dev/null
@@ -1,46 +0,0 @@
-/*
- * (C) Copyright 2009
- * Net Insight <www.netinsight.net>
- * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
- *
- * Based on sheevaplug.h:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301 USA
- */
-
-#ifndef __OPENRD_BASE_H
-#define __OPENRD_BASE_H
-
-#define OPENRD_OE_LOW (~(1<<28)) /* RS232 / RS485 */
-#define OPENRD_OE_HIGH (~(1<<2)) /* SD / UART1 */
-#define OPENRD_OE_VAL_LOW (0) /* Sel RS232 */
-#define OPENRD_OE_VAL_HIGH (1 << 2) /* Sel SD */
-
-/* PHY related */
-#define MV88E1116_LED_FCTRL_REG 10
-#define MV88E1116_CPRSP_CR3_REG 21
-#define MV88E1116_MAC_CTRL_REG 21
-#define MV88E1116_PGADR_REG 22
-#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
-#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
-
-#endif /* __OPENRD_BASE_H */
diff --git a/include/configs/openrd_client.h b/include/configs/openrd_client.h
new file mode 100644
index 0000000..d936ffa
--- /dev/null
+++ b/include/configs/openrd_client.h
@@ -0,0 +1,219 @@
+/*
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+ *
+ * Based on sheevaplug.h:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_OPENRD_CLIENT_H
+#define _CONFIG_OPENRD_CLIENT_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING "\nOpenRD-Client"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_MARVELL 1
+#define CONFIG_ARM926EJS 1 /* Basic Architecture */
+#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_MACH_OPENRD_CLIENT /* Machine type */
+
+#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */
+
+/*
+ * CLKs configurations
+ */
+#define CONFIG_SYS_HZ 1000
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
+ 115200, 230400, 460800, 921600 }
+/* auto boot */
+#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
+
+#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL 1
+#endif
+
+/*
+ * Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE 0x20000 /* 128k */
+#define CONFIG_ENV_ADDR 0x60000
+#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
+ "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
+ "${x_bootcmd_usb}; bootm 0x6400000;"
+
+#define MTDIDS_DEFAULT "nand0=nand_mtd"
+#define MTDPARTS_DEFAULT "mtdparts=nand_mtd:0x100000 at 0x000000(uboot),"\
+ "0x400000 at 0x100000(uImage),"\
+ "0x1fb00000 at 0x500000(rootfs)"
+
+#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
+ "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \
+ "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
+ "x_bootcmd_usb=usb start\0" \
+ "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \
+ "mtdids="MTDIDS_DEFAULT"\0" \
+ "mtdparts="MTDPARTS_DEFAULT"\0"
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB for malloc() */
+/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
+#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
+#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
+#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
+#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* specify more that one ports available */
+#define CONFIG_MII /* expose smi ove miiphy interface */
+#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
+#define CONFIG_KIRKWOOD_EGIGA_PORTS {1, 1}
+#define CONFIG_PHY_BASE_ADR 0x8
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#endif /* CONFIG_CMD_USB */
+
+/*
+ * File system
+ */
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_LZO
+
+#endif /* _CONFIG_OPENRD_CLIENT_H */
diff --git a/include/configs/openrd_ultimate.h b/include/configs/openrd_ultimate.h
new file mode 100644
index 0000000..a0e0417
--- /dev/null
+++ b/include/configs/openrd_ultimate.h
@@ -0,0 +1,219 @@
+/*
+ * (C) Copyright 2009
+ * Net Insight <www.netinsight.net>
+ * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
+ *
+ * Based on sheevaplug.h:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_OPENRD_ULTIMATE_H
+#define _CONFIG_OPENRD_ULTIMATE_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING "\nOpenRD-Ultimate"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_MARVELL 1
+#define CONFIG_ARM926EJS 1 /* Basic Architecture */
+#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_MACH_OPENRD_ULTIMATE /* Machine type */
+
+#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */
+
+/*
+ * CLKs configurations
+ */
+#define CONFIG_SYS_HZ 1000
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
+ 115200, 230400, 460800, 921600 }
+/* auto boot */
+#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
+
+#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL 1
+#endif
+
+/*
+ * Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE 0x20000 /* 128k */
+#define CONFIG_ENV_ADDR 0x60000
+#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
+ "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
+ "${x_bootcmd_usb}; bootm 0x6400000;"
+
+#define MTDIDS_DEFAULT "nand0=nand_mtd"
+#define MTDPARTS_DEFAULT "mtdparts=nand_mtd:0x100000 at 0x000000(uboot),"\
+ "0x400000 at 0x100000(uImage),"\
+ "0x1fb00000 at 0x500000(rootfs)"
+
+#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
+ "=ttyS0,115200 "MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \
+ "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
+ "x_bootcmd_usb=usb start\0" \
+ "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" \
+ "mtdids="MTDIDS_DEFAULT"\0" \
+ "mtdparts="MTDPARTS_DEFAULT"\0"
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB for malloc() */
+/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
+#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
+#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
+#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
+#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* specify more that one ports available */
+#define CONFIG_MII /* expose smi ove miiphy interface */
+#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
+#define CONFIG_KIRKWOOD_EGIGA_PORTS {1, 1}
+#define CONFIG_PHY_BASE_ADR 0
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#endif /* CONFIG_CMD_USB */
+
+/*
+ * File system
+ */
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_LZO
+
+#endif /* _CONFIG_OPENRD_ULTIMATE_H */
--
1.6.6.1
next prev parent reply other threads:[~2010-06-10 9:12 UTC|newest]
Thread overview: 206+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <no>
2008-08-15 2:20 ` [PATCH 00/07] dyn_array/nr_irqs/sparse_irq support v10 - fix Yinghai Lu
2008-08-15 2:20 ` [PATCH 1/7] x86: some debug info for 32bit sparse_irq Yinghai Lu
2008-08-15 2:20 ` [PATCH 2/7] x86: remove union about dest for log/phy Yinghai Lu
2008-08-15 2:20 ` [PATCH 3/7] x86: make 32bit support per_cpu vector fix #1 Yinghai Lu
2008-08-15 2:20 ` [PATCH 4/7] x86_64: rename irq_desc/irq_desc_with_new - fix Yinghai Lu
2008-08-15 2:20 ` [PATCH 5/7] x86: make 32bit support per_cpu vector fix #2 Yinghai Lu
2008-08-15 2:20 ` [PATCH 6/7] x86: ordering functions in io_apic_32.c Yinghai Lu
2008-08-15 2:20 ` [PATCH 7/7] x86: ordering functions in io_apic_64.c Yinghai Lu
2008-08-15 8:21 ` [PATCH 3/7] x86: make 32bit support per_cpu vector fix #1 Ingo Molnar
2008-08-15 8:29 ` Yinghai Lu
2008-08-15 8:51 ` Ingo Molnar
2008-08-15 8:27 ` [PATCH 00/07] dyn_array/nr_irqs/sparse_irq support v10 - fix Ingo Molnar
2008-08-15 8:34 ` Yinghai Lu
2008-08-15 8:51 ` Ingo Molnar
2008-08-15 9:35 ` Ingo Molnar
2008-08-15 10:00 ` Peter Zijlstra
2008-08-15 10:19 ` Ingo Molnar
2008-08-15 10:28 ` Peter Zijlstra
2008-08-15 17:07 ` Yinghai Lu
2008-08-15 23:42 ` [PATCH 0/7] merge io_apic_xx.c Yinghai Lu
2008-08-15 23:42 ` [PATCH 1/7] x86: ordering functions in io_apic_32.c - fix Yinghai Lu
2008-08-15 23:42 ` [PATCH 2/7] x86: make headers files the smae in io_apic_xx.c Yinghai Lu
2008-08-15 23:42 ` [PATCH 3/7] x86: make 64 handle sis_apic_bug like the 32 bit Yinghai Lu
2008-08-15 23:42 ` [PATCH 4/7] x86: remve ioapic_force Yinghai Lu
2008-08-15 23:42 ` [PATCH 5/7] x86: make io_apic_64.c and io_apic_32.c the same Yinghai Lu
2008-08-15 23:42 ` [PATCH 6/7] rename io_apic_64.c to io_apic.c Yinghai Lu
2008-08-15 23:42 ` [PATCH 7/7] make 32 bit have io_apic resource in /proc/iomem Yinghai Lu
2008-08-16 8:02 ` [PATCH 6/7] rename io_apic_64.c to io_apic.c Ingo Molnar
2008-08-16 8:22 ` [PATCH] x86: io_apic.c, build fix Ingo Molnar
2008-08-16 8:26 ` Yinghai Lu
2008-08-18 4:12 ` [PATCH] x86: apic - unify lapic_resume - fix Yinghai Lu
2008-08-18 4:12 ` [PATCH 1/2] x86: make HAVE_SPARSE_IRQ support selectable Yinghai Lu
2008-08-18 4:12 ` [PATCH 2/2] irq: rename irq_desc() to to_irq_desc() Yinghai Lu
2008-08-18 7:37 ` Ingo Molnar
2008-08-18 18:14 ` Yinghai Lu
2008-08-18 7:25 ` [PATCH] x86: apic - unify lapic_resume - fix Ingo Molnar
2008-08-18 20:44 ` [PATCH] irq: rename irq_desc() to to_irq_desc() " Yinghai Lu
2008-08-18 20:44 ` [PATCH] irq: rename irq_desc() to to_irq_desc() - fix #2 Yinghai Lu
2008-08-18 20:44 ` [PATCH] irq: rename irq_desc() to to_irq_desc() - fix #3 Yinghai Lu
2008-08-19 0:11 ` Ingo Molnar
2008-08-19 0:38 ` Ingo Molnar
2008-08-19 0:48 ` Yinghai Lu
2008-08-19 1:16 ` Ingo Molnar
2010-04-15 9:02 ` [U-Boot] [PATCH] OpenRD: Bring PCIe endpoint out of reset Tanmay Upadhyay
2010-04-20 5:51 ` Tanmay Upadhyay
2010-04-30 6:49 ` Prafulla Wadaskar
2010-04-22 13:16 ` [PATCH] OpenRD: Enable SD/UART selection for serial port 1 Tanmay Upadhyay
2010-05-04 12:48 ` [U-Boot] [PATCH] OpenRD: Reset PCIe endpoint while boot-up through PERST# Tanmay Upadhyay
2010-06-10 9:12 ` Tanmay Upadhyay [this message]
2010-06-10 9:16 ` [U-Boot] [PATCH] ARM: Kirkwood: Add support for OpenRD-Client & OpenRD-Ultimate Simon Kagstrom
2010-06-10 9:38 ` Tanmay Upadhyay
2010-06-10 10:25 ` Simon Kagstrom
2010-06-10 19:03 ` Prafulla Wadaskar
2010-06-14 11:02 ` Tanmay Upadhyay
2010-06-13 11:53 ` Albert ARIBAUD
2010-06-13 12:41 ` Wolfgang Denk
2010-06-13 12:51 ` Wolfgang Denk
2010-06-13 13:39 ` Albert ARIBAUD
2010-08-10 8:29 ` [PATCH v2] OpenRD: Enable SD/UART selection for serial port 1 Tanmay Upadhyay
2010-08-10 8:56 ` Alexander Clouter
2010-08-10 8:58 ` Alexander Clouter
2010-08-10 10:27 ` Tanmay Upadhyay
2010-08-10 10:28 ` Alexander Clouter
2010-08-10 10:49 ` Tanmay Upadhyay
2010-08-10 11:53 ` Alexander Clouter
2010-08-11 5:21 ` Tanmay Upadhyay
2010-08-10 8:40 ` [PATCH] ARM: Fix broken Kconfig in arch/arm Tanmay Upadhyay
2011-03-02 8:38 ` [RFC PATCH 1/5] x86/Kconfig: Add Page Cache Accounting entry Liu Yuan
2011-03-02 8:38 ` Liu Yuan
2011-03-02 16:24 ` Randy Dunlap
2011-03-02 16:24 ` Randy Dunlap
2011-03-03 3:11 ` Liu Yuan
2011-03-02 8:38 ` [RFC PATCH 2/5] block: Add functions and data types for Page Cache Accounting Liu Yuan
2011-03-02 8:38 ` Liu Yuan
2011-03-02 8:38 ` [RFC PATCH 3/5] block: Make Page Cache counters work with sysfs Liu Yuan
2011-03-02 8:38 ` Liu Yuan
2011-03-02 8:38 ` [RFC PATCH 4/5] mm: Add hit/miss accounting for Page Cache Liu Yuan
2011-03-02 8:38 ` Liu Yuan
2011-03-02 8:45 ` Ingo Molnar
2011-03-02 8:45 ` Ingo Molnar
2011-03-02 17:02 ` Dave Hansen
2011-03-02 17:02 ` Dave Hansen
2011-03-02 18:49 ` Ingo Molnar
2011-03-02 18:49 ` Ingo Molnar
2011-03-03 0:33 ` Wu Fengguang
2011-03-03 0:33 ` Wu Fengguang
2011-03-03 2:01 ` KOSAKI Motohiro
2011-03-03 2:01 ` KOSAKI Motohiro
2011-03-03 3:14 ` Tao Ma
2011-03-03 3:14 ` Tao Ma
2011-03-03 9:34 ` Ingo Molnar
2011-03-03 9:34 ` Ingo Molnar
2011-03-03 15:08 ` Tao Ma
2011-03-03 15:08 ` Tao Ma
2011-03-02 8:38 ` [RFC PATCH 5/5] mm: Add readpages accounting Liu Yuan
2011-03-02 8:38 ` Liu Yuan
2011-04-18 15:06 ` [v2 0/7] OMAP: GPIO: Use PM runtime framework Varadarajan, Charulatha
2011-04-18 15:06 ` Varadarajan, Charulatha
2011-04-19 6:26 ` Tony Lindgren
2011-04-19 6:26 ` Tony Lindgren
2011-04-20 23:59 ` Kevin Hilman
2011-04-20 23:59 ` Kevin Hilman
2011-04-21 5:42 ` Tony Lindgren
2011-04-21 5:42 ` Tony Lindgren
2011-04-21 15:15 ` Kevin Hilman
2011-04-21 15:15 ` Kevin Hilman
2011-04-22 6:11 ` Tony Lindgren
2011-04-22 6:11 ` Tony Lindgren
2011-04-23 8:35 ` Linus Walleij
2011-04-23 8:35 ` Linus Walleij
2011-04-26 7:29 ` Tony Lindgren
2011-04-26 7:29 ` Tony Lindgren
2011-04-27 13:18 ` Linus Walleij
2011-04-27 13:18 ` Linus Walleij
2011-05-03 16:22 ` Kevin Hilman
2011-05-03 16:22 ` Kevin Hilman
2011-05-03 21:41 ` Linus Walleij
2011-05-03 21:41 ` Linus Walleij
2011-05-04 6:19 ` Tony Lindgren
2011-05-04 6:19 ` Tony Lindgren
2011-05-12 0:57 ` Linus Walleij
2011-05-12 0:57 ` Linus Walleij
2011-05-12 9:42 ` Kevin Hilman
2011-05-12 9:42 ` Kevin Hilman
2011-05-19 19:08 ` Grant Likely
2011-05-19 19:08 ` Grant Likely
2011-05-20 3:34 ` Shawn Guo
2011-05-20 3:34 ` Shawn Guo
2011-05-19 19:05 ` Grant Likely
2011-05-19 19:05 ` Grant Likely
2011-04-18 15:06 ` [PATCH 1/7] OMAP: GPIO: Make gpio_context part of gpio_bank structure Varadarajan, Charulatha
2011-04-18 15:06 ` Varadarajan, Charulatha
2011-04-18 15:06 ` [PATCH 2/7] OMAP: GPIO: Use flag to identify wkup dmn GPIO Varadarajan, Charulatha
2011-04-18 15:06 ` Varadarajan, Charulatha
2011-04-18 15:06 ` [PATCH 3/7] OMAP4: GPIO: Save/restore context Varadarajan, Charulatha
2011-04-18 15:06 ` Varadarajan, Charulatha
2011-04-21 0:26 ` Kevin Hilman
2011-04-21 0:26 ` Kevin Hilman
2011-04-18 15:06 ` [PATCH 4/7] OMAP: GPIO: handle save/restore ctx in GPIO driver Varadarajan, Charulatha
2011-04-18 15:06 ` Varadarajan, Charulatha
2011-04-18 15:06 ` [PATCH 5/7] OMAP2+: GPIO: make workaround_enabled bank specific Varadarajan, Charulatha
2011-04-18 15:06 ` Varadarajan, Charulatha
2011-04-18 15:06 ` [PATCH 6/7] OMAP: GPIO: Cleanup prepare_for_idle/resume Varadarajan, Charulatha
2011-04-18 15:06 ` Varadarajan, Charulatha
2011-04-18 15:06 ` [PATCH 7/7] OMAP: GPIO: use PM runtime framework Varadarajan, Charulatha
2011-04-18 15:06 ` Varadarajan, Charulatha
2011-07-05 7:17 ` [U-Boot] [PATCH v2] Armada100: Add Board Support for Marvell GuruPlug-Display Ajay Bhargav
2011-07-06 5:49 ` Prafulla Wadaskar
2011-07-14 9:37 ` [PATCH 1/2] ARM: pxa168: gplugD: Get rid of mfp-gplugd.h Tanmay Upadhyay
2011-07-18 6:00 ` Eric Miao
2011-07-14 9:37 ` [PATCH 2/2] ARM: pxa168: gplugD: bug-fix: Free correct GPIO Tanmay Upadhyay
2011-07-18 5:59 ` Eric Miao
2011-09-14 5:59 ` [PATCH] mmc: sdhci-pxa: Check pdata before using its members Tanmay Upadhyay
2011-09-14 6:15 ` zhangfei gao
2011-09-21 18:12 ` Chris Ball
2011-11-14 9:43 ` [U-Boot] [Patch V2] mmc: mv_sdhci: Fix host version read for Armada100 Ajay Bhargav
2011-11-25 23:44 ` Andy Fleming
2011-12-06 11:07 ` [PATCH] USB: pxa168: Fix compilation error Tanmay Upadhyay
2011-12-06 11:25 ` Sergei Shtylyov
2011-12-08 4:33 ` [PATCH v2] " Tanmay Upadhyay
2011-12-07 19:57 ` [PATCH] " Alan Stern
2012-02-07 22:58 ` [PATCH v2] add support for AR6003 2048 byte board file Prasanna Kumar
2012-02-08 9:41 ` Kalle Valo
2012-07-10 13:46 ` [Qemu-devel] [PATCH] pseries iommu: h_put_tce split to support more IOMMUs Alexey Kardashevskiy
2012-07-10 13:46 ` [Qemu-devel] [PATCH] pseries pci: removed cached qemu_irq from PCI host bus Alexey Kardashevskiy
2012-07-10 13:46 ` [Qemu-devel] [PATCH] pseries: added allocator for a block of IRQs Alexey Kardashevskiy
2012-07-10 13:46 ` [Qemu-devel] [PATCH] pseries pci: enable debugging with disabled emulated PCI bus Alexey Kardashevskiy
2012-07-10 13:46 ` [Qemu-devel] [PATCH] xics: added end-of-interrupt (EOI) handlers Alexey Kardashevskiy
2012-07-13 8:04 ` Alexey Kardashevskiy
2012-07-10 13:46 ` [Qemu-devel] [PATCH] pseries dma: DMA window params added to PHB and DT population changed Alexey Kardashevskiy
2012-07-25 5:20 ` [PATCH] fixed a macro coding style issue Baodong Chen
2012-07-25 5:27 ` Venu Byravarasu
2012-07-25 5:37 ` Dmitry Torokhov
2012-07-25 6:09 ` Baodong Chen
2012-07-25 6:15 ` Al Viro
2012-07-25 6:36 ` Dmitry Torokhov
2012-07-31 7:27 ` Dmitry Torokhov
2012-09-27 12:51 ` [PATCH 1/8] fs/namespace.c: introduce helper function path_unmounted() Yan Hong
2012-09-27 12:51 ` [PATCH 2/8] fs/namespace.c: remove unused macro MNT_WRITER_UNDERFLOW_LIMIT Yan Hong
2012-09-27 12:51 ` [PATCH 3/8] fs/namespace.c: trivial code clean Yan Hong
2012-09-27 12:51 ` [PATCH 4/8] fs/namespace.c: check permission early in sys_[u]mount Yan Hong
2012-09-27 12:51 ` [PATCH 5/8] fs/namei.c: introduce macro AT_FDINV Yan Hong
2012-09-27 12:51 ` [PATCH 6/8] fs/inode.c: call alloc_inode() in new_inode() directly Yan Hong
2012-09-27 12:51 ` [PATCH 7/8] fs/inode.c: remove outstanding spin lock prefetch Yan Hong
2012-09-27 12:51 ` [PATCH 8/8] vfs: misc comment clean Yan Hong
2013-01-07 18:11 ` [PATCH] Staging: android: fixed const coding style issue in binder.c Patrik Karlin
2013-01-07 23:01 ` Greg KH
2013-11-11 9:27 ` [PATCH 1/2] mklibs: add dependency on dpkg-native Lei Liu
2013-11-11 9:27 ` [PATCH 2/2] Fix grep pattern when mklibs collects executables in rootfs Lei Liu
2013-11-12 10:23 ` Richard Purdie
2013-11-13 3:05 ` Lei Liu
2013-11-22 22:33 ` Nicolas Dechesne
[not found] ` <52955AAB.6000801@gmail.com>
2013-11-27 13:00 ` Nicolas Dechesne
2014-02-08 2:29 ` [PATCH v2] SUNRPC: Allow one callback request to be received from two sk_buff shaobingqing
2014-02-08 19:14 ` Sergei Shtylyov
2014-02-08 19:14 ` Sergei Shtylyov
2014-02-10 17:46 ` Trond Myklebust
2014-02-10 17:46 ` Trond Myklebust
2014-02-11 19:42 ` [PATCH v2] SUNRPC: RPC callbacks may be split across several TCP segments Trond Myklebust
2019-02-18 11:59 ` [PATCH] net/bonding: fix reset active slave Hari Kumar Vemula
2019-02-18 15:58 ` Radu Nicolau
2019-02-20 12:33 ` [dpdk-stable] " Ferruh Yigit
2019-02-20 14:56 ` Radu Nicolau
2019-02-20 15:16 ` Hyong Youb Kim
2019-02-22 1:52 ` Chas Williams
2019-02-22 13:57 ` Ferruh Yigit
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1276161144-20204-1-git-send-email-tanmay.upadhyay@einfochips.com \
--to=tanmay.upadhyay@einfochips.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.