From: Ben Widawsky <benjamin.widawsky@intel.com>
To: Intel GFX <intel-gfx@lists.freedesktop.org>
Cc: Ben Widawsky <ben@bwidawsk.net>,
Ben Widawsky <benjamin.widawsky@intel.com>
Subject: [PATCH 09/15] [v3] drm/i915/bdw: implement semaphore wait
Date: Tue, 17 Dec 2013 15:31:21 -0800 [thread overview]
Message-ID: <1387323081-24314-1-git-send-email-benjamin.widawsky@intel.com> (raw)
In-Reply-To: <20131217192217.GT22448@nuc-i3427.alporthouse.com>
Semaphore waits use a new instruction, MI_SEMAPHORE_WAIT. The seqno to
wait on is all well defined by the table in the previous patch. There is
nothing else different from previous GEN's semaphore synchronization
code.
v2: Update macros to not require the other ring's ring->id (Chris)
v3: Use a condensed GEN8_SEMAPHORE_OFFSET to define the WAIT/SIGNAL
offsets (Chris). To be honest, I prefer the original implementation
because I feel it is more explicit about exactly what is going on. I am
willing to declare I am just unsmart, and leave it there.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
---
drivers/gpu/drm/i915/i915_reg.h | 3 ++
drivers/gpu/drm/i915/intel_ringbuffer.c | 66 +++++++++++++++------------------
drivers/gpu/drm/i915/intel_ringbuffer.h | 30 +++++++++++++++
3 files changed, 62 insertions(+), 37 deletions(-)
diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index 5c3bf66..a47463f 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -242,6 +242,9 @@
#define MI_RESTORE_INHIBIT (1<<0)
#define MI_SEMAPHORE_SIGNAL MI_INSTR(0x1b, 0) /* GEN8+ */
#define MI_SEMAPHORE_TARGET(engine) ((engine)<<15)
+#define MI_SEMAPHORE_WAIT MI_INSTR(0x1c, 2) /* GEN8+ */
+#define MI_SEMAPHORE_POLL (1<<15)
+#define MI_SEMAPHORE_SAD_GTE_SDD (1<<12)
#define MI_STORE_DWORD_IMM MI_INSTR(0x20, 1)
#define MI_MEM_VIRTUAL (1 << 22) /* 965+ only */
#define MI_STORE_DWORD_INDEX MI_INSTR(0x21, 1)
diff --git a/drivers/gpu/drm/i915/intel_ringbuffer.c b/drivers/gpu/drm/i915/intel_ringbuffer.c
index d6e664d..f87b704 100644
--- a/drivers/gpu/drm/i915/intel_ringbuffer.c
+++ b/drivers/gpu/drm/i915/intel_ringbuffer.c
@@ -796,6 +796,31 @@ static inline bool i915_gem_has_seqno_wrapped(struct drm_device *dev,
* @signaller - ring which has, or will signal
* @seqno - seqno which the waiter will block on
*/
+
+static int
+gen8_ring_sync(struct intel_ring_buffer *waiter,
+ struct intel_ring_buffer *signaller,
+ u32 seqno)
+{
+ struct drm_i915_private *dev_priv = waiter->dev->dev_private;
+ int ret;
+
+ ret = intel_ring_begin(waiter, 4);
+ if (ret)
+ return ret;
+
+ intel_ring_emit(waiter, MI_SEMAPHORE_WAIT |
+ MI_SEMAPHORE_GLOBAL_GTT |
+ MI_SEMAPHORE_SAD_GTE_SDD);
+ intel_ring_emit(waiter, seqno);
+ intel_ring_emit(waiter,
+ lower_32_bits(GEN8_WAIT_OFFSET(waiter, signaller->id)));
+ intel_ring_emit(waiter,
+ upper_32_bits(GEN8_WAIT_OFFSET(waiter, signaller->id)));
+ intel_ring_advance(waiter);
+ return 0;
+}
+
static int
gen6_ring_sync(struct intel_ring_buffer *waiter,
struct intel_ring_buffer *signaller,
@@ -1934,39 +1959,6 @@ static int gen6_ring_flush(struct intel_ring_buffer *ring,
return 0;
}
-/* seqno size is actually only a uint32, but since we plan to use MI_FLUSH_DW to
- * do the writes, and that must have qw aligned offsets, simply pretend it's 8b.
- */
-#define SEQNO_SIZE sizeof(uint64_t)
-#define GEN8_SIGNAL_OFFSET(to) \
- (i915_gem_obj_ggtt_offset(dev_priv->semaphore_obj) + \
- (ring->id * I915_NUM_RINGS * SEQNO_SIZE) + \
- (SEQNO_SIZE * (to)))
-
-#define GEN8_WAIT_OFFSET(from) \
- (i915_gem_obj_ggtt_offset(dev_priv->semaphore_obj) + \
- ((from) * I915_NUM_RINGS * SEQNO_SIZE) + \
- (SEQNO_SIZE * ring->id))
-
-#define GEN8_RING_SEMAPHORE_INIT do { \
- if (!dev_priv->semaphore_obj) { \
- break; \
- } \
- ring->semaphore.signal_ggtt[RCS] = GEN8_SIGNAL_OFFSET(RCS); \
- ring->semaphore.signal_ggtt[VCS] = GEN8_SIGNAL_OFFSET(VCS); \
- ring->semaphore.signal_ggtt[BCS] = GEN8_SIGNAL_OFFSET(BCS); \
- ring->semaphore.signal_ggtt[VECS] = GEN8_SIGNAL_OFFSET(VECS); \
- ring->semaphore.mbox[RCS] = GEN8_WAIT_OFFSET(RCS); \
- ring->semaphore.mbox[VCS] = GEN8_WAIT_OFFSET(VCS); \
- ring->semaphore.mbox[BCS] = GEN8_WAIT_OFFSET(BCS); \
- ring->semaphore.mbox[VECS] = GEN8_WAIT_OFFSET(VECS); \
- ring->semaphore.signal_ggtt[ring->id] = MI_SEMAPHORE_SYNC_INVALID; \
- ring->semaphore.mbox[ring->id] = GEN6_NOSYNC; \
- } while(0)
-#undef seqno_size
-
-
-
int intel_init_render_ring_buffer(struct drm_device *dev)
{
drm_i915_private_t *dev_priv = dev->dev_private;
@@ -2002,7 +1994,7 @@ int intel_init_render_ring_buffer(struct drm_device *dev)
ring->irq_enable_mask = GT_RENDER_USER_INTERRUPT;
ring->get_seqno = gen6_ring_get_seqno;
ring->set_seqno = ring_set_seqno;
- ring->semaphore.sync_to = gen6_ring_sync;
+ ring->semaphore.sync_to = gen8_ring_sync;
if (i915_semaphore_is_enabled(dev)) {
BUG_ON(!dev_priv->semaphore_obj);
ring->semaphore.signal = gen8_rcs_signal;
@@ -2187,7 +2179,7 @@ int intel_init_bsd_ring_buffer(struct drm_device *dev)
ring->irq_put = gen8_ring_put_irq;
ring->dispatch_execbuffer =
gen8_ring_dispatch_execbuffer;
- ring->semaphore.sync_to = gen6_ring_sync;
+ ring->semaphore.sync_to = gen8_ring_sync;
if (i915_semaphore_is_enabled(dev)) {
ring->semaphore.signal = gen8_xcs_signal;
GEN8_RING_SEMAPHORE_INIT;
@@ -2252,7 +2244,7 @@ int intel_init_blt_ring_buffer(struct drm_device *dev)
ring->irq_get = gen8_ring_get_irq;
ring->irq_put = gen8_ring_put_irq;
ring->dispatch_execbuffer = gen8_ring_dispatch_execbuffer;
- ring->semaphore.sync_to = gen6_ring_sync;
+ ring->semaphore.sync_to = gen8_ring_sync;
if (i915_semaphore_is_enabled(dev)) {
ring->semaphore.signal = gen8_xcs_signal;
GEN8_RING_SEMAPHORE_INIT;
@@ -2301,7 +2293,7 @@ int intel_init_vebox_ring_buffer(struct drm_device *dev)
ring->irq_get = gen8_ring_get_irq;
ring->irq_put = gen8_ring_put_irq;
ring->dispatch_execbuffer = gen8_ring_dispatch_execbuffer;
- ring->semaphore.sync_to = gen6_ring_sync;
+ ring->semaphore.sync_to = gen8_ring_sync;
if (i915_semaphore_is_enabled(dev)) {
ring->semaphore.signal = gen8_xcs_signal;
GEN8_RING_SEMAPHORE_INIT;
diff --git a/drivers/gpu/drm/i915/intel_ringbuffer.h b/drivers/gpu/drm/i915/intel_ringbuffer.h
index cbaa346..26beade 100644
--- a/drivers/gpu/drm/i915/intel_ringbuffer.h
+++ b/drivers/gpu/drm/i915/intel_ringbuffer.h
@@ -33,6 +33,36 @@ struct intel_hw_status_page {
#define I915_READ_IMR(ring) I915_READ(RING_IMR((ring)->mmio_base))
#define I915_WRITE_IMR(ring, val) I915_WRITE(RING_IMR((ring)->mmio_base), val)
+/* seqno size is actually only a uint32, but since we plan to use MI_FLUSH_DW to
+ * do the writes, and that must have qw aligned offsets, simply pretend it's 8b.
+ */
+#define i915_semaphore_seqno_size sizeof(uint64_t)
+#define GEN8_SEMAPHORE_OFFSET(from, to) \
+ (i915_gem_obj_ggtt_offset(dev_priv->semaphore_obj) + \
+ ((from) * I915_NUM_RINGS + (to)) * i915_semaphore_seqno_size)
+
+#define GEN8_SIGNAL_OFFSET(to) \
+ GEN8_SEMAPHORE_OFFSET(ring->id, to)
+
+#define GEN8_WAIT_OFFSET(__ring, from) \
+ GEN8_SEMAPHORE_OFFSET(from, (__ring)->id)
+
+#define GEN8_RING_SEMAPHORE_INIT do { \
+ if (!dev_priv->semaphore_obj) { \
+ break; \
+ } \
+ ring->semaphore.signal_ggtt[RCS] = GEN8_SIGNAL_OFFSET(RCS); \
+ ring->semaphore.signal_ggtt[VCS] = GEN8_SIGNAL_OFFSET(VCS); \
+ ring->semaphore.signal_ggtt[BCS] = GEN8_SIGNAL_OFFSET(BCS); \
+ ring->semaphore.signal_ggtt[VECS] = GEN8_SIGNAL_OFFSET(VECS); \
+ ring->semaphore.mbox[RCS] = GEN8_WAIT_OFFSET(ring, RCS); \
+ ring->semaphore.mbox[VCS] = GEN8_WAIT_OFFSET(ring, VCS); \
+ ring->semaphore.mbox[BCS] = GEN8_WAIT_OFFSET(ring, BCS); \
+ ring->semaphore.mbox[VECS] = GEN8_WAIT_OFFSET(ring, VECS); \
+ ring->semaphore.signal_ggtt[ring->id] = MI_SEMAPHORE_SYNC_INVALID; \
+ ring->semaphore.mbox[ring->id] = GEN6_NOSYNC; \
+ } while(0)
+
enum intel_ring_hangcheck_action {
HANGCHECK_IDLE = 0,
HANGCHECK_WAIT,
--
1.8.5.1
next prev parent reply other threads:[~2013-12-17 23:31 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-12-17 4:50 [PATCH 00/15] [v2] Broadwell HW semaphore Ben Widawsky
2013-12-17 4:50 ` [PATCH 01/15] drm/i915: Reorder/respace MI instruction definition Ben Widawsky
2013-12-17 23:06 ` [PATCH 01.5/15] drm/i915: Make semaphore modparam RO Ben Widawsky
2013-12-17 4:50 ` [PATCH 02/15] drm/i915: Don't emit mbox updates without semaphores Ben Widawsky
2013-12-17 19:24 ` Chris Wilson
2013-12-17 22:02 ` Ben Widawsky
2013-12-17 22:47 ` Chris Wilson
2013-12-17 4:50 ` [PATCH 03/15] drm/i915: Move semaphore specific ring members to struct Ben Widawsky
2013-12-17 4:50 ` [PATCH 04/15] drm/i915: Virtualize the ringbuffer signal func Ben Widawsky
2013-12-17 4:50 ` [PATCH 05/15] drm/i915: Move ring_begin to signal() Ben Widawsky
2013-12-17 4:50 ` [PATCH 06/15] drm/i915: Make semaphore updates more precise Ben Widawsky
2013-12-17 9:49 ` Chris Wilson
2013-12-17 4:50 ` [PATCH 07/15] drm/i915: gen specific ring init Ben Widawsky
2013-12-17 8:52 ` Daniel Vetter
2013-12-17 4:50 ` [PATCH 08/15] drm/i915/bdw: implement semaphore signal Ben Widawsky
2013-12-17 19:11 ` Chris Wilson
2013-12-17 23:00 ` [PATCH 08/15] [v3] " Ben Widawsky
2013-12-17 4:50 ` [PATCH 09/15] drm/i915/bdw: implement semaphore wait Ben Widawsky
2013-12-17 19:22 ` Chris Wilson
2013-12-17 23:31 ` Ben Widawsky [this message]
2013-12-17 4:50 ` [PATCH 10/15] drm/i915: FORCE_RESTORE for gen8 semaphores Ben Widawsky
2013-12-17 4:50 ` [PATCH 11/15] drm/i915/bdw: poll semaphores Ben Widawsky
2013-12-17 19:17 ` Chris Wilson
2013-12-17 4:50 ` [PATCH 12/15] drm/i915: Extract semaphore error collection Ben Widawsky
2013-12-17 19:14 ` Chris Wilson
2013-12-17 23:37 ` Ben Widawsky
2013-12-17 4:50 ` [PATCH 13/15] drm/i915/bdw: collect semaphore error state Ben Widawsky
2013-12-17 4:50 ` [PATCH 14/15] drm/i915: unleash semaphores on gen8 Ben Widawsky
2013-12-17 4:50 ` [PATCH 15/15] drm/i915: semaphore debugfs Ben Widawsky
2013-12-17 9:17 ` [PATCH 00/15] [v2] Broadwell HW semaphore Daniel Vetter
2013-12-17 16:29 ` Damien Lespiau
2013-12-17 18:21 ` Daniel Vetter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1387323081-24314-1-git-send-email-benjamin.widawsky@intel.com \
--to=benjamin.widawsky@intel.com \
--cc=ben@bwidawsk.net \
--cc=intel-gfx@lists.freedesktop.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.