All of lore.kernel.org
 help / color / mirror / Atom feed
From: YoungJun Cho <yj44.cho@samsung.com>
To: airlied@linux.ie, dri-devel@lists.freedesktop.org
Cc: mark.rutland@arm.com, devicetree@vger.kernel.org,
	linux-samsung-soc@vger.kernel.org, pawel.moll@arm.com,
	ijc+devicetree@hellion.org.uk, sw0312.kim@samsung.com,
	a.hajda@samsung.com, kyungmin.park@samsung.com,
	robh+dt@kernel.org, galak@codeaurora.org, kgene.kim@samsung.com
Subject: [PATCH v4 08/14] drm/exynos: dsi: add driver data to support Exynos5420
Date: Thu, 05 Jun 2014 15:19:48 +0900	[thread overview]
Message-ID: <1401949194-20092-9-git-send-email-yj44.cho@samsung.com> (raw)
In-Reply-To: <1401949194-20092-1-git-send-email-yj44.cho@samsung.com>

The offset of register DSIM_PLLTMR_REG in Exynos5420 is
different from the one in Exynos4 SoC.

In case of Exynos5420 SoC, there is no frequency band bit
in DSIM_PLLCTRL_REG,
and it uses DSIM_PHYCTRL_REG and DSIM_PHYTIMING*_REG instead.
So this patch adds driver data to distinguish it.

Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
---
 drivers/gpu/drm/exynos/exynos_drm_dsi.c |  157 ++++++++++++++++++++++++++-----
 1 file changed, 135 insertions(+), 22 deletions(-)

diff --git a/drivers/gpu/drm/exynos/exynos_drm_dsi.c b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
index db760d8..c348392 100644
--- a/drivers/gpu/drm/exynos/exynos_drm_dsi.c
+++ b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
@@ -17,6 +17,7 @@
 
 #include <linux/clk.h>
 #include <linux/irq.h>
+#include <linux/of_device.h>
 #include <linux/phy/phy.h>
 #include <linux/regulator/consumer.h>
 #include <linux/component.h>
@@ -55,9 +56,12 @@
 
 /* FIFO memory AC characteristic register */
 #define DSIM_PLLCTRL_REG	0x4c	/* PLL control register */
-#define DSIM_PLLTMR_REG		0x50	/* PLL timer register */
 #define DSIM_PHYACCHR_REG	0x54	/* D-PHY AC characteristic register */
 #define DSIM_PHYACCHR1_REG	0x58	/* D-PHY AC characteristic register1 */
+#define DSIM_PHYCTRL_REG	0x5c
+#define DSIM_PHYTIMING_REG	0x64
+#define DSIM_PHYTIMING1_REG	0x68
+#define DSIM_PHYTIMING2_REG	0x6c
 
 /* DSIM_STATUS */
 #define DSIM_STOP_STATE_DAT(x)		(((x) & 0xf) << 0)
@@ -201,6 +205,24 @@
 #define DSIM_PLL_M(x)			((x) << 4)
 #define DSIM_PLL_S(x)			((x) << 1)
 
+/* DSIM_PHYCTRL */
+#define DSIM_PHYCTRL_ULPS_EXIT(x)	(((x) & 0x1ff) << 0)
+
+/* DSIM_PHYTIMING */
+#define DSIM_PHYTIMING_LPX(x)		((x) << 8)
+#define DSIM_PHYTIMING_HS_EXIT(x)	((x) << 0)
+
+/* DSIM_PHYTIMING1 */
+#define DSIM_PHYTIMING1_CLK_PREPARE(x)	((x) << 24)
+#define DSIM_PHYTIMING1_CLK_ZERO(x)	((x) << 16)
+#define DSIM_PHYTIMING1_CLK_POST(x)	((x) << 8)
+#define DSIM_PHYTIMING1_CLK_TRAIL(x)	((x) << 0)
+
+/* DSIM_PHYTIMING2 */
+#define DSIM_PHYTIMING2_HS_PREPARE(x)	((x) << 16)
+#define DSIM_PHYTIMING2_HS_ZERO(x)	((x) << 8)
+#define DSIM_PHYTIMING2_HS_TRAIL(x)	((x) << 0)
+
 #define DSI_MAX_BUS_WIDTH		4
 #define DSI_NUM_VIRTUAL_CHANNELS	4
 #define DSI_TX_FIFO_SIZE		2048
@@ -234,6 +256,12 @@ struct exynos_dsi_transfer {
 #define DSIM_STATE_INITIALIZED		BIT(1)
 #define DSIM_STATE_CMD_LPM		BIT(2)
 
+struct exynos_dsi_driver_data {
+	unsigned int plltmr_reg;
+
+	unsigned int has_freqband:1;
+};
+
 struct exynos_dsi {
 	struct mipi_dsi_host dsi_host;
 	struct drm_connector connector;
@@ -263,11 +291,39 @@ struct exynos_dsi {
 
 	spinlock_t transfer_lock; /* protects transfer_list */
 	struct list_head transfer_list;
+
+	struct exynos_dsi_driver_data *driver_data;
 };
 
 #define host_to_dsi(host) container_of(host, struct exynos_dsi, dsi_host)
 #define connector_to_dsi(c) container_of(c, struct exynos_dsi, connector)
 
+static struct exynos_dsi_driver_data exynos4_dsi_driver_data = {
+	.plltmr_reg = 0x50,
+	.has_freqband = 1,
+};
+
+static struct exynos_dsi_driver_data exynos5_dsi_driver_data = {
+	.plltmr_reg = 0x58,
+};
+
+static struct of_device_id exynos_dsi_of_match[] = {
+	{ .compatible = "samsung,exynos4210-mipi-dsi",
+	  .data = &exynos4_dsi_driver_data },
+	{ .compatible = "samsung,exynos5420-mipi-dsi",
+	  .data = &exynos5_dsi_driver_data },
+	{ }
+};
+
+static inline struct exynos_dsi_driver_data *exynos_dsi_get_driver_data(
+						struct platform_device *pdev)
+{
+	const struct of_device_id *of_id =
+			of_match_device(exynos_dsi_of_match, &pdev->dev);
+
+	return (struct exynos_dsi_driver_data *)of_id->data;
+}
+
 static void exynos_dsi_wait_for_reset(struct exynos_dsi *dsi)
 {
 	if (wait_for_completion_timeout(&dsi->completed, msecs_to_jiffies(300)))
@@ -341,14 +397,9 @@ static unsigned long exynos_dsi_pll_find_pms(struct exynos_dsi *dsi,
 static unsigned long exynos_dsi_set_pll(struct exynos_dsi *dsi,
 					unsigned long freq)
 {
-	static const unsigned long freq_bands[] = {
-		100 * MHZ, 120 * MHZ, 160 * MHZ, 200 * MHZ,
-		270 * MHZ, 320 * MHZ, 390 * MHZ, 450 * MHZ,
-		510 * MHZ, 560 * MHZ, 640 * MHZ, 690 * MHZ,
-		770 * MHZ, 870 * MHZ, 950 * MHZ,
-	};
+	struct exynos_dsi_driver_data *driver_data = dsi->driver_data;
 	unsigned long fin, fout;
-	int timeout, band;
+	int timeout;
 	u8 p, s;
 	u16 m;
 	u32 reg;
@@ -369,18 +420,30 @@ static unsigned long exynos_dsi_set_pll(struct exynos_dsi *dsi,
 			"failed to find PLL PMS for requested frequency\n");
 		return -EFAULT;
 	}
+	dev_dbg(dsi->dev, "PLL freq %lu, (p %d, m %d, s %d)\n", fout, p, m, s);
 
-	for (band = 0; band < ARRAY_SIZE(freq_bands); ++band)
-		if (fout < freq_bands[band])
-			break;
+	writel(500, dsi->reg_base + driver_data->plltmr_reg);
+
+	reg = DSIM_PLL_EN | DSIM_PLL_P(p) | DSIM_PLL_M(m) | DSIM_PLL_S(s);
+
+	if (driver_data->has_freqband) {
+		static const unsigned long freq_bands[] = {
+			100 * MHZ, 120 * MHZ, 160 * MHZ, 200 * MHZ,
+			270 * MHZ, 320 * MHZ, 390 * MHZ, 450 * MHZ,
+			510 * MHZ, 560 * MHZ, 640 * MHZ, 690 * MHZ,
+			770 * MHZ, 870 * MHZ, 950 * MHZ,
+		};
+		int band;
+
+		for (band = 0; band < ARRAY_SIZE(freq_bands); ++band)
+			if (fout < freq_bands[band])
+				break;
 
-	dev_dbg(dsi->dev, "PLL freq %lu, (p %d, m %d, s %d), band %d\n", fout,
-		p, m, s, band);
+		dev_dbg(dsi->dev, "band %d\n", band);
 
-	writel(500, dsi->reg_base + DSIM_PLLTMR_REG);
+		reg |= DSIM_FREQ_BAND(band);
+	}
 
-	reg = DSIM_FREQ_BAND(band) | DSIM_PLL_EN
-			| DSIM_PLL_P(p) | DSIM_PLL_M(m) | DSIM_PLL_S(s);
 	writel(reg, dsi->reg_base + DSIM_PLLCTRL_REG);
 
 	timeout = 1000;
@@ -434,6 +497,59 @@ static int exynos_dsi_enable_clock(struct exynos_dsi *dsi)
 	return 0;
 }
 
+static void exynos_dsi_set_phy_ctrl(struct exynos_dsi *dsi)
+{
+	struct exynos_dsi_driver_data *driver_data = dsi->driver_data;
+	u32 reg;
+
+	if (driver_data->has_freqband)
+		return;
+
+	/* B D-PHY: D-PHY Master & Slave Analog Block control */
+	reg = DSIM_PHYCTRL_ULPS_EXIT(0x0af);
+	writel(reg, dsi->reg_base + DSIM_PHYCTRL_REG);
+
+	/*
+	 * T LPX: Transmitted length of any Low-Power state period
+	 * T HS-EXIT: Time that the transmitter drives LP-11 following a HS
+	 *	burst
+	 */
+	reg = DSIM_PHYTIMING_LPX(0x06) | DSIM_PHYTIMING_HS_EXIT(0x0b);
+	writel(reg, dsi->reg_base + DSIM_PHYTIMING_REG);
+
+	/*
+	 * T CLK-PREPARE: Time that the transmitter drives the Clock Lane LP-00
+	 *	Line state immediately before the HS-0 Line state starting the
+	 *	HS transmission
+	 * T CLK-ZERO: Time that the transmitter drives the HS-0 state prior to
+	 *	transmitting the Clock.
+	 * T CLK_POST: Time that the transmitter continues to send HS clock
+	 *	after the last associated Data Lane has transitioned to LP Mode
+	 *	Interval is defined as the period from the end of T HS-TRAIL to
+	 *	the beginning of T CLK-TRAIL
+	 * T CLK-TRAIL: Time that the transmitter drives the HS-0 state after
+	 *	the last payload clock bit of a HS transmission burst
+	 */
+	reg = DSIM_PHYTIMING1_CLK_PREPARE(0x07) |
+			DSIM_PHYTIMING1_CLK_ZERO(0x27) |
+			DSIM_PHYTIMING1_CLK_POST(0x0d) |
+			DSIM_PHYTIMING1_CLK_TRAIL(0x08);
+	writel(reg, dsi->reg_base + DSIM_PHYTIMING1_REG);
+
+	/*
+	 * T HS-PREPARE: Time that the transmitter drives the Data Lane LP-00
+	 *	Line state immediately before the HS-0 Line state starting the
+	 *	HS transmission
+	 * T HS-ZERO: Time that the transmitter drives the HS-0 state prior to
+	 *	transmitting the Sync sequence.
+	 * T HS-TRAIL: Time that the transmitter drives the flipped differential
+	 *	state after last payload data bit of a HS transmission burst
+	 */
+	reg = DSIM_PHYTIMING2_HS_PREPARE(0x09) | DSIM_PHYTIMING2_HS_ZERO(0x0d) |
+			DSIM_PHYTIMING2_HS_TRAIL(0x0b);
+	writel(reg, dsi->reg_base + DSIM_PHYTIMING2_REG);
+}
+
 static void exynos_dsi_disable_clock(struct exynos_dsi *dsi)
 {
 	u32 reg;
@@ -948,10 +1064,11 @@ static irqreturn_t exynos_dsi_irq(int irq, void *dev_id)
 
 static int exynos_dsi_init(struct exynos_dsi *dsi)
 {
-	exynos_dsi_enable_clock(dsi);
 	exynos_dsi_reset(dsi);
 	enable_irq(dsi->irq);
+	exynos_dsi_enable_clock(dsi);
 	exynos_dsi_wait_for_reset(dsi);
+	exynos_dsi_set_phy_ctrl(dsi);
 	exynos_dsi_init_link(dsi);
 
 	return 0;
@@ -1457,6 +1574,7 @@ static int exynos_dsi_probe(struct platform_device *pdev)
 	dsi->dsi_host.dev = &pdev->dev;
 
 	dsi->dev = &pdev->dev;
+	dsi->driver_data = exynos_dsi_get_driver_data(pdev);
 
 	ret = exynos_dsi_parse_dt(dsi);
 	if (ret)
@@ -1539,11 +1657,6 @@ static int exynos_dsi_remove(struct platform_device *pdev)
 	return 0;
 }
 
-static struct of_device_id exynos_dsi_of_match[] = {
-	{ .compatible = "samsung,exynos4210-mipi-dsi" },
-	{ }
-};
-
 struct platform_driver dsi_driver = {
 	.probe = exynos_dsi_probe,
 	.remove = exynos_dsi_remove,
-- 
1.7.9.5

  parent reply	other threads:[~2014-06-05  6:19 UTC|newest]

Thread overview: 19+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-06-05  6:19 [PATCH v4 00/14] drm/exynos: support LCD I80 interface display YoungJun Cho
2014-06-05  6:19 ` [PATCH v4 01/14] drm/exynos: dsi: move the EoT packets configuration point YoungJun Cho
2014-06-05  6:19 ` [PATCH v4 02/14] drm/exynos: use wait_event_timeout() for safety usage YoungJun Cho
2014-06-05  6:19 ` [PATCH v4 03/14] ARM: dts: samsung-fimd: add LCD I80 interface specific properties YoungJun Cho
2014-06-05  6:19 ` [PATCH v4 04/14] drm/exynos: add TE handler to support LCD I80 interface YoungJun Cho
2014-06-05  6:19 ` [PATCH v4 05/14] drm/exynos: dsi: " YoungJun Cho
2014-06-05  6:19 ` [PATCH v4 06/14] drm/exynos: fimd: " YoungJun Cho
2014-06-05  6:19 ` [PATCH v4 07/14] ARM: dts: exynos_dsim: add exynos5420 compatible to DT bindings YoungJun Cho
2014-06-05  6:19 ` YoungJun Cho [this message]
2014-06-05  6:19 ` [PATCH v4 09/14] ARM: dts: s6e3fa0: add " YoungJun Cho
2014-06-05  6:19 ` [PATCH v4 10/14] drm/panel: add S6E3FA0 driver YoungJun Cho
2014-06-05  6:19 ` [PATCH v4 11/14] ARM: dts: exynos4: add system register property YoungJun Cho
2014-06-05  6:19 ` [PATCH v4 12/14] ARM: dts: exynos5: " YoungJun Cho
2014-06-05  6:19 ` [PATCH v4 13/14] ARM: dts: exynos5420: add mipi-phy node YoungJun Cho
2014-06-05  6:19 ` [PATCH v4 14/14] ARM: dts: exynos5420: add dsi node YoungJun Cho
2014-06-05  8:14 ` [PATCH v4 00/14] drm/exynos: support LCD I80 interface display Inki Dae
2014-06-05  8:20   ` Thierry Reding
2014-06-05  8:43     ` Inki Dae
2014-06-05  8:51       ` Thierry Reding

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1401949194-20092-9-git-send-email-yj44.cho@samsung.com \
    --to=yj44.cho@samsung.com \
    --cc=a.hajda@samsung.com \
    --cc=airlied@linux.ie \
    --cc=devicetree@vger.kernel.org \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=galak@codeaurora.org \
    --cc=ijc+devicetree@hellion.org.uk \
    --cc=kgene.kim@samsung.com \
    --cc=kyungmin.park@samsung.com \
    --cc=linux-samsung-soc@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=pawel.moll@arm.com \
    --cc=robh+dt@kernel.org \
    --cc=sw0312.kim@samsung.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.