From: Jun Nie <jun.nie@linaro.org>
To: broonie@kernel.org, lgirdwood@gmail.com
Cc: alsa-devel@alsa-project.org, shawn.guo@linaro.org,
wan.zhijun@zte.com.cn, Jun Nie <jun.nie@linaro.org>
Subject: [PATCH v3 4/6] ASoC: zx: Add zx296702 SPDIF support
Date: Fri, 29 May 2015 21:31:19 +0800 [thread overview]
Message-ID: <1432906281-27698-5-git-send-email-jun.nie@linaro.org> (raw)
In-Reply-To: <1432906281-27698-1-git-send-email-jun.nie@linaro.org>
Add driver for zx296702 SPDIF controller
Signed-off-by: Jun Nie <jun.nie@linaro.org>
---
sound/soc/Kconfig | 1 +
sound/soc/Makefile | 1 +
sound/soc/zte/Kconfig | 8 +
sound/soc/zte/Makefile | 1 +
sound/soc/zte/zx296702-spdif.c | 370 +++++++++++++++++++++++++++++++++++++++++
5 files changed, 381 insertions(+)
create mode 100644 sound/soc/zte/Kconfig
create mode 100644 sound/soc/zte/Makefile
create mode 100644 sound/soc/zte/zx296702-spdif.c
diff --git a/sound/soc/Kconfig b/sound/soc/Kconfig
index 3ba52da..e2828e1 100644
--- a/sound/soc/Kconfig
+++ b/sound/soc/Kconfig
@@ -57,6 +57,7 @@ source "sound/soc/tegra/Kconfig"
source "sound/soc/txx9/Kconfig"
source "sound/soc/ux500/Kconfig"
source "sound/soc/xtensa/Kconfig"
+source "sound/soc/zte/Kconfig"
# Supported codecs
source "sound/soc/codecs/Kconfig"
diff --git a/sound/soc/Makefile b/sound/soc/Makefile
index 974ba70..57bf32d 100644
--- a/sound/soc/Makefile
+++ b/sound/soc/Makefile
@@ -38,3 +38,4 @@ obj-$(CONFIG_SND_SOC) += tegra/
obj-$(CONFIG_SND_SOC) += txx9/
obj-$(CONFIG_SND_SOC) += ux500/
obj-$(CONFIG_SND_SOC) += xtensa/
+obj-$(CONFIG_SND_SOC) += zte/
diff --git a/sound/soc/zte/Kconfig b/sound/soc/zte/Kconfig
new file mode 100644
index 0000000..4f05573
--- /dev/null
+++ b/sound/soc/zte/Kconfig
@@ -0,0 +1,8 @@
+config ZX296702_SPDIF
+ tristate "ZX296702 spdif"
+ depends on SOC_ZX296702 || COMPILE_TEST
+ depends on COMMON_CLK
+ select SND_SOC_GENERIC_DMAENGINE_PCM
+ help
+ Say Y or M if you want to add support for codecs attached to the
+ zx296702 spdif interface
diff --git a/sound/soc/zte/Makefile b/sound/soc/zte/Makefile
new file mode 100644
index 0000000..fb3a4a0
--- /dev/null
+++ b/sound/soc/zte/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_ZX296702_SPDIF) += zx296702-spdif.o
diff --git a/sound/soc/zte/zx296702-spdif.c b/sound/soc/zte/zx296702-spdif.c
new file mode 100644
index 0000000..f108f39
--- /dev/null
+++ b/sound/soc/zte/zx296702-spdif.c
@@ -0,0 +1,370 @@
+/*
+ * Copyright (C) 2015 Linaro
+ *
+ * Author: Jun Nie <jun.nie@linaro.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/dmaengine.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <sound/asoundef.h>
+#include <sound/core.h>
+#include <sound/dmaengine_pcm.h>
+#include <sound/initval.h>
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
+#include <sound/soc-dai.h>
+
+#define ZX_CTRL 0x04
+#define ZX_FIFOCTRL 0x08
+#define ZX_INT_STATUS 0x10
+#define ZX_INT_MASK 0x14
+#define ZX_DATA 0x18
+#define ZX_VALID_BIT 0x1c
+#define ZX_CH_STA_1 0x20
+#define ZX_CH_STA_2 0x24
+#define ZX_CH_STA_3 0x28
+#define ZX_CH_STA_4 0x2c
+#define ZX_CH_STA_5 0x30
+#define ZX_CH_STA_6 0x34
+
+#define ZX_CTRL_MODA_16 (0 << 6)
+#define ZX_CTRL_MODA_18 BIT(6)
+#define ZX_CTRL_MODA_20 (2 << 6)
+#define ZX_CTRL_MODA_24 (3 << 6)
+#define ZX_CTRL_MODA_MASK (3 << 6)
+
+#define ZX_CTRL_ENB BIT(4)
+#define ZX_CTRL_DNB (0 << 4)
+#define ZX_CTRL_ENB_MASK BIT(4)
+
+#define ZX_CTRL_TX_OPEN BIT(0)
+#define ZX_CTRL_TX_CLOSE (0 << 0)
+#define ZX_CTRL_TX_MASK BIT(0)
+
+#define ZX_CTRL_OPEN (ZX_CTRL_TX_OPEN | ZX_CTRL_ENB)
+#define ZX_CTRL_CLOSE (ZX_CTRL_TX_CLOSE | ZX_CTRL_DNB)
+
+#define ZX_CTRL_DOUBLE_TRACK (0 << 8)
+#define ZX_CTRL_LEFT_TRACK BIT(8)
+#define ZX_CTRL_RIGHT_TRACK (2 << 8)
+#define ZX_CTRL_TRACK_MASK (3 << 8)
+
+#define ZX_FIFOCTRL_TXTH_MASK (0x1f << 8)
+#define ZX_FIFOCTRL_TXTH(x) (x << 8)
+#define ZX_FIFOCTRL_TX_DMA_EN BIT(2)
+#define ZX_FIFOCTRL_TX_DMA_DIS (0 << 2)
+#define ZX_FIFOCTRL_TX_DMA_EN_MASK BIT(2)
+#define ZX_FIFOCTRL_TX_FIFO_RST BIT(0)
+#define ZX_FIFOCTRL_TX_FIFO_RST_MASK BIT(0)
+
+#define ZX_VALID_DOUBLE_TRACK (0 << 0)
+#define ZX_VALID_LEFT_TRACK BIT(1)
+#define ZX_VALID_RIGHT_TRACK (2 << 0)
+#define ZX_VALID_TRACK_MASK (3 << 0)
+
+#define ZX_SPDIF_CLK_RAT (4 * 32)
+
+struct zx_spdif_info {
+ struct snd_dmaengine_dai_dma_data dma_data;
+ struct clk *dai_clk;
+ void __iomem *reg_base;
+ resource_size_t mapbase;
+};
+
+static int zx_spdif_dai_probe(struct snd_soc_dai *dai)
+{
+ struct zx_spdif_info *zx_spdif = dev_get_drvdata(dai->dev);
+
+ snd_soc_dai_set_drvdata(dai, zx_spdif);
+ zx_spdif->dma_data.addr = zx_spdif->mapbase + ZX_DATA;
+ zx_spdif->dma_data.maxburst = 8;
+ snd_soc_dai_init_dma_data(dai, &zx_spdif->dma_data, NULL);
+ return 0;
+}
+
+static int zx_spdif_chanstats(void __iomem *base, unsigned int rate)
+{
+ u32 cstas1;
+
+ switch (rate) {
+ case 22050:
+ cstas1 = IEC958_AES3_CON_FS_22050;
+ break;
+ case 24000:
+ cstas1 = IEC958_AES3_CON_FS_24000;
+ break;
+ case 32000:
+ cstas1 = IEC958_AES3_CON_FS_32000;
+ break;
+ case 44100:
+ cstas1 = IEC958_AES3_CON_FS_44100;
+ break;
+ case 48000:
+ cstas1 = IEC958_AES3_CON_FS_48000;
+ break;
+ case 88200:
+ cstas1 = IEC958_AES3_CON_FS_88200;
+ break;
+ case 96000:
+ cstas1 = IEC958_AES3_CON_FS_96000;
+ break;
+ case 176400:
+ cstas1 = IEC958_AES3_CON_FS_176400;
+ break;
+ case 192000:
+ cstas1 = IEC958_AES3_CON_FS_192000;
+ break;
+ default:
+ return -EINVAL;
+ }
+ cstas1 = cstas1 << 24;
+ cstas1 |= IEC958_AES0_CON_NOT_COPYRIGHT;
+
+ writel_relaxed(cstas1, base + ZX_CH_STA_1);
+ return 0;
+}
+
+static int zx_spdif_hw_params(struct snd_pcm_substream *substream,
+ struct snd_pcm_hw_params *params,
+ struct snd_soc_dai *socdai)
+{
+ struct zx_spdif_info *zx_spdif = dev_get_drvdata(socdai->dev);
+ struct zx_spdif_info *spdif = snd_soc_dai_get_drvdata(socdai);
+ struct snd_dmaengine_dai_dma_data *dma_data = &zx_spdif->dma_data;
+ u32 val, ch_num, rate;
+ int ret;
+
+ dma_data = snd_soc_dai_get_dma_data(socdai, substream);
+ dma_data->addr_width = params_width(params) >> 3;
+
+ val = readl_relaxed(zx_spdif->reg_base + ZX_CTRL);
+ val &= ~ZX_CTRL_MODA_MASK;
+ switch (params_format(params)) {
+ case SNDRV_PCM_FORMAT_S16_LE:
+ val |= ZX_CTRL_MODA_16;
+ break;
+
+ case SNDRV_PCM_FORMAT_S18_3LE:
+ val |= ZX_CTRL_MODA_18;
+ break;
+
+ case SNDRV_PCM_FORMAT_S20_3LE:
+ val |= ZX_CTRL_MODA_20;
+ break;
+
+ case SNDRV_PCM_FORMAT_S24_LE:
+ val |= ZX_CTRL_MODA_24;
+ break;
+ default:
+ dev_err(socdai->dev, "Format not support!\n");
+ return -EINVAL;
+ }
+
+ ch_num = params_channels(params);
+ if (ch_num == 2)
+ val |= ZX_CTRL_DOUBLE_TRACK;
+ else
+ val |= ZX_CTRL_LEFT_TRACK;
+ writel_relaxed(val, zx_spdif->reg_base + ZX_CTRL);
+
+ val = readl_relaxed(zx_spdif->reg_base + ZX_VALID_BIT);
+ val &= ~ZX_VALID_TRACK_MASK;
+ if (ch_num == 2)
+ val |= ZX_VALID_DOUBLE_TRACK;
+ else
+ val |= ZX_VALID_RIGHT_TRACK;
+ writel_relaxed(val, zx_spdif->reg_base + ZX_VALID_BIT);
+
+ rate = params_rate(params);
+ ret = zx_spdif_chanstats(zx_spdif->reg_base, rate);
+ if (ret)
+ return ret;
+ ret = clk_set_rate(spdif->dai_clk, rate * ch_num * ZX_SPDIF_CLK_RAT);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static void zx_spdif_cfg_tx(void __iomem *base, int on)
+{
+ u32 val;
+
+ val = readl_relaxed(base + ZX_CTRL);
+ val &= ~(ZX_CTRL_ENB_MASK | ZX_CTRL_TX_MASK);
+ val |= on ? ZX_CTRL_OPEN : ZX_CTRL_CLOSE;
+ writel_relaxed(val, base + ZX_CTRL);
+
+ val = readl_relaxed(base + ZX_FIFOCTRL);
+ val &= ~ZX_FIFOCTRL_TX_DMA_EN_MASK;
+ if (on)
+ val |= ZX_FIFOCTRL_TX_DMA_EN;
+ writel_relaxed(val, base + ZX_FIFOCTRL);
+}
+
+static int zx_spdif_trigger(struct snd_pcm_substream *substream, int cmd,
+ struct snd_soc_dai *dai)
+{
+ u32 val;
+ struct zx_spdif_info *zx_spdif = dev_get_drvdata(dai->dev);
+ int ret = 0;
+
+ switch (cmd) {
+ case SNDRV_PCM_TRIGGER_START:
+ val = readl_relaxed(zx_spdif->reg_base + ZX_FIFOCTRL);
+ val |= ZX_FIFOCTRL_TX_FIFO_RST;
+ writel_relaxed(val, zx_spdif->reg_base + ZX_FIFOCTRL);
+ /* fall thru */
+ case SNDRV_PCM_TRIGGER_RESUME:
+ case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
+ zx_spdif_cfg_tx(zx_spdif->reg_base, true);
+ break;
+
+ case SNDRV_PCM_TRIGGER_STOP:
+ case SNDRV_PCM_TRIGGER_SUSPEND:
+ case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
+ zx_spdif_cfg_tx(zx_spdif->reg_base, false);
+ break;
+
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ return ret;
+}
+
+static int zx_spdif_startup(struct snd_pcm_substream *substream,
+ struct snd_soc_dai *dai)
+{
+ struct zx_spdif_info *zx_spdif = dev_get_drvdata(dai->dev);
+
+ return clk_prepare_enable(zx_spdif->dai_clk);
+}
+
+static void zx_spdif_shutdown(struct snd_pcm_substream *substream,
+ struct snd_soc_dai *dai)
+{
+ struct zx_spdif_info *zx_spdif = dev_get_drvdata(dai->dev);
+
+ clk_disable_unprepare(zx_spdif->dai_clk);
+}
+
+#define ZX_RATES \
+ (SNDRV_PCM_RATE_22050 | SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 | \
+ SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_88200 | SNDRV_PCM_RATE_96000 |\
+ SNDRV_PCM_RATE_176400 | SNDRV_PCM_RATE_192000)
+
+#define ZX_FORMAT \
+ (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S18_3LE \
+ | SNDRV_PCM_FMTBIT_S20_3LE | SNDRV_PCM_FMTBIT_S24_LE)
+
+static struct snd_soc_dai_ops zx_spdif_dai_ops = {
+ .trigger = zx_spdif_trigger,
+ .startup = zx_spdif_startup,
+ .shutdown = zx_spdif_shutdown,
+ .hw_params = zx_spdif_hw_params,
+};
+
+static struct snd_soc_dai_driver zx_spdif_dai = {
+ .name = "spdif",
+ .id = 0,
+ .probe = zx_spdif_dai_probe,
+ .playback = {
+ .channels_min = 1,
+ .channels_max = 2,
+ .rates = ZX_RATES,
+ .formats = ZX_FORMAT,
+ },
+ .ops = &zx_spdif_dai_ops,
+};
+
+static const struct snd_soc_component_driver zx_spdif_component = {
+ .name = "spdif",
+};
+
+static void zx_spdif_dev_init(void __iomem *base)
+{
+ u32 val;
+
+ writel_relaxed(0, base + ZX_CTRL);
+ writel_relaxed(0, base + ZX_INT_MASK);
+ writel_relaxed(0xf, base + ZX_INT_STATUS);
+ writel_relaxed(0x1, base + ZX_FIFOCTRL);
+
+ val = readl_relaxed(base + ZX_FIFOCTRL);
+ val &= ~(ZX_FIFOCTRL_TXTH_MASK | ZX_FIFOCTRL_TX_FIFO_RST_MASK);
+ val |= ZX_FIFOCTRL_TXTH(8);
+ writel_relaxed(val, base + ZX_FIFOCTRL);
+}
+
+static int zx_spdif_probe(struct platform_device *pdev)
+{
+ struct resource *res;
+ struct zx_spdif_info *zx_spdif;
+ int ret;
+
+ zx_spdif = kzalloc(sizeof(*zx_spdif), GFP_KERNEL);
+ if (!zx_spdif)
+ return -ENOMEM;
+
+ zx_spdif->dai_clk = devm_clk_get(&pdev->dev, "tx");
+ if (IS_ERR(zx_spdif->dai_clk)) {
+ dev_err(&pdev->dev, "Fail to get clk\n");
+ return PTR_ERR(zx_spdif->dai_clk);
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ zx_spdif->mapbase = res->start;
+ zx_spdif->reg_base = devm_ioremap_resource(&pdev->dev, res);
+ if (!zx_spdif->reg_base) {
+ dev_err(&pdev->dev, "ioremap failed!\n");
+ return -EIO;
+ }
+
+ zx_spdif_dev_init(zx_spdif->reg_base);
+ platform_set_drvdata(pdev, zx_spdif);
+
+ ret = snd_soc_register_component(&pdev->dev, &zx_spdif_component,
+ &zx_spdif_dai, 1);
+ if (ret) {
+ dev_err(&pdev->dev, "Register DAI failed: %d\n", ret);
+ return ret;
+ }
+
+ ret = devm_snd_dmaengine_pcm_register(&pdev->dev, NULL, 0);
+ if (ret)
+ dev_err(&pdev->dev, "Register platform PCM failed: %d\n", ret);
+
+ return ret;
+}
+
+static const struct of_device_id zx_spdif_dt_ids[] = {
+ { .compatible = "zte,zx296702-spdif", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, zx_spdif_dt_ids);
+
+static struct platform_driver spdif_driver = {
+ .probe = zx_spdif_probe,
+ .driver = {
+ .name = "zx-spdif",
+ .owner = THIS_MODULE,
+ .of_match_table = zx_spdif_dt_ids,
+ },
+};
+
+module_platform_driver(spdif_driver);
+
+MODULE_AUTHOR("Jun Nie <jun.nie@linaro.org>");
+MODULE_DESCRIPTION("ZTE SPDIF SoC DAI");
+MODULE_LICENSE("GPL");
--
1.9.1
next prev parent reply other threads:[~2015-05-29 13:32 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-05-29 13:31 [PATCH v3 0/6] Support ZTE zx296702 SPDIF/I2S Jun Nie
2015-05-29 13:31 ` [PATCH v3 1/6] dt: Add documentation for the ZTE SPDIF controller Jun Nie
2015-05-29 13:31 ` [PATCH v3 2/6] dt: Add documentation for the ZTE I2S controller Jun Nie
2015-05-29 13:31 ` [PATCH v3 3/6] dt: Add doc for the ZTE HDMI audio codec binding Jun Nie
2015-05-29 13:31 ` Jun Nie [this message]
2015-05-29 14:03 ` [PATCH v3 4/6] ASoC: zx: Add zx296702 SPDIF support Lars-Peter Clausen
2015-05-29 13:31 ` [PATCH v3 5/6] ASoC: zx: Add ZTE zx296702 I2S DAI driver Jun Nie
2015-06-03 16:02 ` Mark Brown
2015-05-29 13:31 ` [PATCH v3 6/6] ASoC: zx: add zx296702 hdmi codec Jun Nie
2015-05-29 14:10 ` Lars-Peter Clausen
2015-05-29 15:18 ` Mark Brown
2015-06-01 1:42 ` Jun Nie
2015-06-02 18:13 ` Mark Brown
2015-06-03 1:47 ` Jun Nie
2015-06-03 11:01 ` Mark Brown
2015-06-03 12:40 ` Jun Nie
2015-06-03 15:09 ` Mark Brown
2015-06-03 17:58 ` Mark Brown
2015-06-04 3:35 ` Jun Nie
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1432906281-27698-5-git-send-email-jun.nie@linaro.org \
--to=jun.nie@linaro.org \
--cc=alsa-devel@alsa-project.org \
--cc=broonie@kernel.org \
--cc=lgirdwood@gmail.com \
--cc=shawn.guo@linaro.org \
--cc=wan.zhijun@zte.com.cn \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.