[PATCH v3 07/33] drm/i915: Perform async fbdev initialisation much later

From: Chris Wilson <chris@chris-wilson.co.uk>
To: intel-gfx@lists.freedesktop.org
Subject: [PATCH v3 07/33] drm/i915: Perform async fbdev initialisation much later
Date: Fri,  3 Jun 2016 15:36:50 +0100	[thread overview]
Message-ID: <1464964636-3877-8-git-send-email-chris@chris-wilson.co.uk> (raw)
In-Reply-To: <1464964636-3877-1-git-send-email-chris@chris-wilson.co.uk>

Setting up fbdev requires everything ready and registered (in particular
the connectors). In the next patch, we defer registration of the KMS
objects and unless we defer setting off fbdev, it may run before they are
registered and oops.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
---
 drivers/gpu/drm/i915/i915_dma.c | 24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_dma.c b/drivers/gpu/drm/i915/i915_dma.c
index 07edaed9d5a2..650b3f7e2a8e 100644
--- a/drivers/gpu/drm/i915/i915_dma.c
+++ b/drivers/gpu/drm/i915/i915_dma.c
@@ -525,18 +525,6 @@ static int i915_load_modeset_init(struct drm_device *dev)
 	/* Only enable hotplug handling once the fbdev is fully set up. */
 	intel_hpd_init(dev_priv);
 
-	/*
-	 * Some ports require correctly set-up hpd registers for detection to
-	 * work properly (leading to ghost connected connector status), e.g. VGA
-	 * on gm45.  Hence we can only set up the initial fbdev config after hpd
-	 * irqs are fully enabled. Now we should scan for the initial config
-	 * only once hotplug handling is enabled, but due to screwed-up locking
-	 * around kms/fbdev init we can't protect the fdbev initial config
-	 * scanning against hotplug events. Hence do this first and ignore the
-	 * tiny window where we will loose hotplug notifactions.
-	 */
-	intel_fbdev_initial_config_async(dev);
-
 	drm_kms_helper_poll_init(dev);
 
 	return 0;
@@ -1384,6 +1372,18 @@ static void i915_driver_register(struct drm_i915_private *dev_priv)
 		intel_gpu_ips_init(dev_priv);
 
 	i915_audio_component_init(dev_priv);
+
+	/*
+	 * Some ports require correctly set-up hpd registers for detection to
+	 * work properly (leading to ghost connected connector status), e.g. VGA
+	 * on gm45.  Hence we can only set up the initial fbdev config after hpd
+	 * irqs are fully enabled. Now we should scan for the initial config
+	 * only once hotplug handling is enabled, but due to screwed-up locking
+	 * around kms/fbdev init we can't protect the fdbev initial config
+	 * scanning against hotplug events. Hence do this first and ignore the
+	 * tiny window where we will loose hotplug notifactions.
+	 */
+	intel_fbdev_initial_config_async(dev);
 }
 
 /**
-- 
2.8.1

_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
