All of lore.kernel.org
 help / color / mirror / Atom feed
From: Amit Nischal <anischal@codeaurora.org>
To: Stephen Boyd <sboyd@kernel.org>,
	Michael Turquette <mturquette@baylibre.com>
Cc: Andy Gross <andy.gross@linaro.org>,
	David Brown <david.brown@linaro.org>,
	Rajendra Nayak <rnayak@codeaurora.org>,
	Odelu Kukatla <okukatla@codeaurora.org>,
	Taniya Das <tdas@codeaurora.org>,
	linux-arm-msm@vger.kernel.org, linux-soc@vger.kernel.org,
	linux-clk@vger.kernel.org, linux-kernel@vger.kernel.org,
	Amit Nischal <anischal@codeaurora.org>
Subject: [PATCH v2 2/4] clk: qcom: Add clk_rcg2_gfx3d_ops for SDM845
Date: Thu, 12 Jul 2018 22:39:39 +0530	[thread overview]
Message-ID: <1531415381-16885-3-git-send-email-anischal@codeaurora.org> (raw)
In-Reply-To: <1531415381-16885-1-git-send-email-anischal@codeaurora.org>

To turn on the gpu_gx_gdsc, there is a hardware requirement to
turn on the root clock (GFX3D RCG) first which would be the turn
on signal for the gdsc along with the SW_COLLAPSE. As per the
current implementation of clk_rcg2_shared_ops, it clears the
root_enable bit in the enable() clock op. But due to the above
said requirement for GFX3D shared RCG, root_enable bit would be
already set by gdsc driver and clk_rcg2_shared_enable()should
not clear the root unless the disable is called.

Add support for the same by reusing the existing clk_rcg2_shared_ops
and deriving "clk_rcg2_gfx3d_ops" clk_ops for GFX3D clock to take
care of the root set/clear requirement.

Signed-off-by: Amit Nischal <anischal@codeaurora.org>
---
 drivers/clk/qcom/clk-rcg.h  |  1 +
 drivers/clk/qcom/clk-rcg2.c | 87 +++++++++++++++++++++++++++++++++++++++++++--
 2 files changed, 86 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/qcom/clk-rcg.h b/drivers/clk/qcom/clk-rcg.h
index b209a2f..c8c9558 100644
--- a/drivers/clk/qcom/clk-rcg.h
+++ b/drivers/clk/qcom/clk-rcg.h
@@ -160,5 +160,6 @@ struct clk_rcg2 {
 extern const struct clk_ops clk_pixel_ops;
 extern const struct clk_ops clk_gfx3d_ops;
 extern const struct clk_ops clk_rcg2_shared_ops;
+extern const struct clk_ops clk_rcg2_gfx3d_ops;

 #endif
diff --git a/drivers/clk/qcom/clk-rcg2.c b/drivers/clk/qcom/clk-rcg2.c
index 52208d4..667edd9 100644
--- a/drivers/clk/qcom/clk-rcg2.c
+++ b/drivers/clk/qcom/clk-rcg2.c
@@ -866,7 +866,7 @@ static int clk_rcg2_shared_set_rate_and_parent(struct clk_hw *hw,
 	return clk_rcg2_shared_set_rate(hw, rate, parent_rate);
 }

-static int clk_rcg2_shared_enable(struct clk_hw *hw)
+static int __clk_rcg2_shared_enable(struct clk_hw *hw)
 {
 	struct clk_rcg2 *rcg = to_clk_rcg2(hw);
 	int ret;
@@ -879,7 +879,14 @@ static int clk_rcg2_shared_enable(struct clk_hw *hw)
 	if (ret)
 		return ret;

-	ret = update_config(rcg);
+	return update_config(rcg);
+}
+
+static int clk_rcg2_shared_enable(struct clk_hw *hw)
+{
+	int ret;
+
+	ret = __clk_rcg2_shared_enable(hw);
 	if (ret)
 		return ret;

@@ -929,3 +936,79 @@ static void clk_rcg2_shared_disable(struct clk_hw *hw)
 	.set_rate_and_parent = clk_rcg2_shared_set_rate_and_parent,
 };
 EXPORT_SYMBOL_GPL(clk_rcg2_shared_ops);
+
+static int clk_rcg2_gfx3d_enable(struct clk_hw *hw)
+{
+	return __clk_rcg2_shared_enable(hw);
+}
+
+static int clk_rcg2_gfx3d_determine_rate(struct clk_hw *hw,
+					struct clk_rate_request *req)
+{
+	struct clk_rate_request parent_req = { };
+	struct clk_hw *p;
+	unsigned long rate = req->rate;
+	int ret;
+
+	if (rate < req->min_rate || rate > req->max_rate)
+		return -EINVAL;
+
+	/* Get fixed parent - GPU_CC_PLL0_OUT_EVEN */
+	p = clk_hw_get_parent_by_index(hw, 1);
+
+	/* Parent should always run at twice of the requested rate */
+	parent_req.rate = 2 * req->rate;
+
+	ret = __clk_determine_rate(req->best_parent_hw, &parent_req);
+	if (ret)
+		return ret;
+
+	req->best_parent_hw = p;
+	req->best_parent_rate = parent_req.rate;
+	req->rate = parent_req.rate / 2;
+
+	return 0;
+}
+
+static int clk_rcg2_gfx3d_set_rate(struct clk_hw *hw, unsigned long rate,
+				    unsigned long parent_rate)
+{
+	struct clk_rcg2 *rcg = to_clk_rcg2(hw);
+	int ret;
+	u32 cfg;
+
+	/* Configure fixed SRC and DIV */
+	cfg = rcg->parent_map[1].cfg << CFG_SRC_SEL_SHIFT;
+	cfg |= 0x3 << CFG_SRC_DIV_SHIFT;
+
+	ret = regmap_write(rcg->clkr.regmap, rcg->cmd_rcgr + CFG_REG, cfg);
+	if (ret)
+		return ret;
+
+	/*
+	 * In case clock is disabled, update the SRC and DIV only
+	 * and return without configuration update.
+	 */
+	if (!__clk_is_enabled(hw->clk))
+		return 0;
+
+	return update_config(rcg);
+}
+
+static int clk_rcg2_gfx3d_set_rate_and_parent(struct clk_hw *hw,
+		unsigned long rate, unsigned long parent_rate, u8 index)
+{
+	return clk_rcg2_gfx3d_set_rate(hw, rate, parent_rate);
+}
+
+const struct clk_ops clk_rcg2_gfx3d_ops = {
+	.enable = clk_rcg2_gfx3d_enable,
+	.disable = clk_rcg2_shared_disable,
+	.get_parent = clk_rcg2_get_parent,
+	.set_parent = clk_rcg2_set_parent,
+	.recalc_rate = clk_rcg2_recalc_rate,
+	.determine_rate = clk_rcg2_gfx3d_determine_rate,
+	.set_rate = clk_rcg2_gfx3d_set_rate,
+	.set_rate_and_parent = clk_rcg2_gfx3d_set_rate_and_parent,
+};
+EXPORT_SYMBOL_GPL(clk_rcg2_gfx3d_ops);
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation

  parent reply	other threads:[~2018-07-12 17:09 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-07-12 17:09 [PATCH v2 0/4] Add QCOM graphics clock controller driver for SDM845 Amit Nischal
2018-07-12 17:09 ` [PATCH v2 1/4] clk: qcom: gdsc: Add support to enable/disable the clocks with GDSC Amit Nischal
2018-07-12 17:09 ` Amit Nischal [this message]
2018-07-12 17:09 ` [PATCH v2 3/4] dt-bindings: clock: Introduce QCOM Graphics clock bindings Amit Nischal
2018-07-12 17:09 ` [PATCH v2 4/4] clk: qcom: Add graphics clock controller driver for SDM845 Amit Nischal
2018-07-14  0:46   ` kbuild test robot
2018-07-14  0:46     ` kbuild test robot
2018-07-14  3:20   ` kbuild test robot
2018-07-14  3:20     ` kbuild test robot

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1531415381-16885-3-git-send-email-anischal@codeaurora.org \
    --to=anischal@codeaurora.org \
    --cc=andy.gross@linaro.org \
    --cc=david.brown@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-soc@vger.kernel.org \
    --cc=mturquette@baylibre.com \
    --cc=okukatla@codeaurora.org \
    --cc=rnayak@codeaurora.org \
    --cc=sboyd@kernel.org \
    --cc=tdas@codeaurora.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.