From: Raju P L S S S N <rplsssn@codeaurora.org>
To: andy.gross@linaro.org, david.brown@linaro.org,
linux-arm-msm@vger.kernel.org, linux-soc@vger.kernel.org
Cc: rnayak@codeaurora.org, bjorn.andersson@linaro.org,
linux-kernel@vger.kernel.org, sboyd@kernel.org,
evgreen@chromium.org, dianders@chromium.org, mka@chromium.org,
ilina@codeaurora.org, "Raju P.L.S.S.S.N" <rplsssn@codeaurora.org>
Subject: [PATCH v2 0/6] drivers/qcom: add additional functionality to RPMH
Date: Fri, 27 Jul 2018 15:34:43 +0530 [thread overview]
Message-ID: <1532685889-31345-1-git-send-email-rplsssn@codeaurora.org> (raw)
From: "Raju P.L.S.S.S.N" <rplsssn@codeaurora.org>
Changes in v1:
- Remove unnecessary EXPORT_SYMBOL in rpmh-rsc
This set of patches add additional functionality to RPMH drivers[1].
PM drivers can choose to disallow idle modes when RSC controller is busy
sending or processing requests. The patches add necessary functions to
query the controller status.
The controllers may be in 'solver' state, where they could be in autonomous
mode executing low power modes for their hardware and as such are not
available for sending active votes. Functionality to get notified about
such state and disallow requests for state change in that case is added
in these patches.
The Power Domain Controller can be programmed to wakeup the RSC and
setup the resources back in the active state, before the processor is
woken up by a timer interrupt. The wakeup value from the timer hardware
can be copied to the PDC which has its own timer and is in an always-on
power domain. Programming the wakeup value is done through a separate
register on the RSC. Functions necessary to program wakeup is added in
the patches.
Please consider reviewing this patchset.
v1:https://lkml.org/lkml/2018/7/19/213
[1] https://lkml.org/lkml/2018/6/20/519
Lina Iyer (5):
drivers: qcom: rpmh-rsc: return if the controller is idle
drivers: qcom: rpmh: export controller idle status
drivers: qcom: rpmh: disallow active requests in solver mode
drivers: qcom: rpmh-rsc: write PDC data
drivers: qcom: rpmh: write PDC data
Raju P.L.S.S.S.N (1):
drivers: qcom: rpmh-rsc: clear active mode configuration for waketcs
drivers/soc/qcom/rpmh-internal.h | 6 ++
drivers/soc/qcom/rpmh-rsc.c | 132 ++++++++++++++++++++++++++++++---------
drivers/soc/qcom/rpmh.c | 100 +++++++++++++++++++++++++++++
include/soc/qcom/rpmh.h | 16 +++++
4 files changed, 225 insertions(+), 29 deletions(-)
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,\na Linux Foundation Collaborative Project
next reply other threads:[~2018-07-27 10:04 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-07-27 10:04 Raju P L S S S N [this message]
2018-07-27 10:04 ` [PATCH v2 1/6] drivers: qcom: rpmh-rsc: return if the controller is idle Raju P L S S S N
2018-09-11 22:39 ` Matthias Kaehlcke
2018-09-12 2:20 ` Lina Iyer
2018-07-27 10:04 ` [PATCH v2 2/6] drivers: qcom: rpmh: export controller idle status Raju P L S S S N
2018-07-27 10:04 ` [PATCH v2 3/6] drivers: qcom: rpmh: disallow active requests in solver mode Raju P L S S S N
2018-09-11 23:02 ` Matthias Kaehlcke
2018-09-12 2:22 ` Lina Iyer
2018-07-27 10:04 ` [PATCH v2 4/6] drivers: qcom: rpmh-rsc: clear active mode configuration for waketcs Raju P L S S S N
2018-09-12 21:51 ` Matthias Kaehlcke
2018-07-27 10:04 ` [PATCH v2 5/6] drivers: qcom: rpmh-rsc: write PDC data Raju P L S S S N
2018-09-12 22:28 ` Matthias Kaehlcke
2018-09-12 22:33 ` Lina Iyer
2018-09-12 22:37 ` Matthias Kaehlcke
2018-07-27 10:04 ` [PATCH v2 6/6] drivers: qcom: rpmh: " Raju P L S S S N
2018-09-12 22:55 ` Matthias Kaehlcke
2018-09-05 20:05 ` [PATCH v2 0/6] drivers/qcom: add additional functionality to RPMH Lina Iyer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1532685889-31345-1-git-send-email-rplsssn@codeaurora.org \
--to=rplsssn@codeaurora.org \
--cc=andy.gross@linaro.org \
--cc=bjorn.andersson@linaro.org \
--cc=david.brown@linaro.org \
--cc=dianders@chromium.org \
--cc=evgreen@chromium.org \
--cc=ilina@codeaurora.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-soc@vger.kernel.org \
--cc=mka@chromium.org \
--cc=rnayak@codeaurora.org \
--cc=sboyd@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.