From: Sandeep Maheswaram <sanm@codeaurora.org>
To: Rob Herring <robh+dt@kernel.org>, Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Felipe Balbi <balbi@kernel.org>,
Stephen Boyd <swboyd@chromium.org>,
Doug Anderson <dianders@chromium.org>,
Matthias Kaehlcke <mka@chromium.org>
Cc: devicetree@vger.kernel.org, linux-arm-msm@vger.kernel.org,
linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org,
Manu Gautam <mgautam@codeaurora.org>,
Sandeep Maheswaram <sanm@codeaurora.org>
Subject: [PATCH v4 1/2] arm64: dts: qcom: sc7280: Add USB related nodes
Date: Fri, 4 Jun 2021 16:33:37 +0530 [thread overview]
Message-ID: <1622804618-18480-2-git-send-email-sanm@codeaurora.org> (raw)
In-Reply-To: <1622804618-18480-1-git-send-email-sanm@codeaurora.org>
Add nodes for DWC3 USB controller, QMP and HS USB PHYs in sc7280 SOC.
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
---
changed usb3-phy to lanes in qmp phy node as it was causing probe failure.
arch/arm64/boot/dts/qcom/sc7280.dtsi | 149 +++++++++++++++++++++++++++++++++++
1 file changed, 149 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 0b6f119..d70d5fb 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -973,6 +973,110 @@
};
};
+ usb_1_hsphy: phy@88e3000 {
+ compatible = "qcom,sc7280-usb-hs-phy",
+ "qcom,usb-snps-hs-7nm-phy";
+ reg = <0 0x088e3000 0 0x400>;
+ status = "disabled";
+ #phy-cells = <0>;
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "ref";
+
+ resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+ };
+
+ usb_2_hsphy: phy@88e4000 {
+ compatible = "qcom,sc7280-usb-hs-phy",
+ "qcom,usb-snps-hs-7nm-phy";
+ reg = <0 0x088e4000 0 0x400>;
+ status = "disabled";
+ #phy-cells = <0>;
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "ref";
+
+ resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
+ };
+
+ usb_1_qmpphy: phy-wrapper@88e9000 {
+ compatible = "qcom,sm8250-qmp-usb3-phy";
+ reg = <0 0x088e9000 0 0x200>,
+ <0 0x088e8000 0 0x20>;
+ reg-names = "reg-base", "dp_com";
+ status = "disabled";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
+ clock-names = "aux", "ref_clk_src", "com_aux";
+
+ resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
+ <&gcc GCC_USB3_PHY_PRIM_BCR>;
+ reset-names = "phy", "common";
+
+ usb_1_ssphy: lanes@88e9200 {
+ reg = <0 0x088e9200 0 0x200>,
+ <0 0x088e9400 0 0x200>,
+ <0 0x088e9c00 0 0x400>,
+ <0 0x088e9600 0 0x200>,
+ <0 0x088e9800 0 0x200>,
+ <0 0x088e9a00 0 0x100>;
+ #phy-cells = <0>;
+ #clock-cells = <1>;
+ clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "usb3_phy_pipe_clk_src";
+ };
+ };
+
+ usb_2: usb@8cf8800 {
+ compatible = "qcom,sc7280-dwc3", "qcom,dwc3";
+ reg = <0 0x08cf8800 0 0x400>;
+ status = "disabled";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ dma-ranges;
+
+ clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
+ <&gcc GCC_USB30_SEC_MASTER_CLK>,
+ <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
+ <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_SEC_SLEEP_CLK>;
+ clock-names = "cfg_noc", "core", "iface","mock_utmi",
+ "sleep";
+
+ assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_SEC_MASTER_CLK>;
+ assigned-clock-rates = <19200000>, <200000000>;
+
+ interrupts-extended = <&intc GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+ <&pdc 13 IRQ_TYPE_EDGE_RISING>,
+ <&pdc 12 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "hs_phy_irq",
+ "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+ power-domains = <&gcc GCC_USB30_SEC_GDSC>;
+
+ resets = <&gcc GCC_USB30_SEC_BCR>;
+
+ usb_2_dwc3: dwc3@8c00000 {
+ compatible = "snps,dwc3";
+ reg = <0 0x08c00000 0 0xe000>;
+ interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&apps_smmu 0xa0 0x0>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_enblslpm_quirk;
+ phys = <&usb_2_hsphy>;
+ phy-names = "usb2-phy";
+ maximum-speed = "high-speed";
+ };
+ };
+
system-cache-controller@9200000 {
compatible = "qcom,sc7280-llcc";
reg = <0 0x09200000 0 0xd0000>, <0 0x09600000 0 0x50000>;
@@ -980,6 +1084,51 @@
interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>;
};
+ usb_1: usb@a6f8800 {
+ compatible = "qcom,sc7280-dwc3", "qcom,dwc3";
+ reg = <0 0x0a6f8800 0 0x400>;
+ status = "disabled";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ dma-ranges;
+
+ clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+ <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
+ clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+ "sleep";
+
+ assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+ assigned-clock-rates = <19200000>, <200000000>;
+
+ interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+ <&pdc 14 IRQ_TYPE_EDGE_BOTH>,
+ <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
+ <&pdc 17 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hs_phy_irq", "dp_hs_phy_irq",
+ "dm_hs_phy_irq", "ss_phy_irq";
+
+ power-domains = <&gcc GCC_USB30_PRIM_GDSC>;
+
+ resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+ usb_1_dwc3: dwc3@a600000 {
+ compatible = "snps,dwc3";
+ reg = <0 0x0a600000 0 0xe000>;
+ interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&apps_smmu 0xe0 0x0>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_enblslpm_quirk;
+ phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+ phy-names = "usb2-phy", "usb3-phy";
+ maximum-speed = "super-speed";
+ };
+ };
+
videocc: clock-controller@aaf0000 {
compatible = "qcom,sc7280-videocc";
reg = <0 0xaaf0000 0 0x10000>;
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2021-06-04 11:04 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-04 11:03 [PATCH v4 0/2] Add DT bindings and DT nodes for USB in SC7280 Sandeep Maheswaram
2021-06-04 11:03 ` Sandeep Maheswaram [this message]
2021-06-04 21:40 ` [PATCH v4 1/2] arm64: dts: qcom: sc7280: Add USB related nodes Stephen Boyd
2021-06-06 3:59 ` Bjorn Andersson
2021-06-04 11:03 ` [PATCH v4 2/2] arm64: dts: qcom: sc7280: Add USB nodes for IDP board Sandeep Maheswaram
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1622804618-18480-2-git-send-email-sanm@codeaurora.org \
--to=sanm@codeaurora.org \
--cc=agross@kernel.org \
--cc=balbi@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=dianders@chromium.org \
--cc=gregkh@linuxfoundation.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=mgautam@codeaurora.org \
--cc=mka@chromium.org \
--cc=robh+dt@kernel.org \
--cc=swboyd@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.