From: Randy Dunlap <rdunlap@xenotime.net>
To: Luciano Coelho <coelho@ti.com>
Cc: matti.j.aaltonen@nokia.com, johannes@sipsolutions.net,
linux-kernel@vger.kernel.org, sameo@linux.intel.com,
mchehab@infradead.org, linux-media@vger.kernel.org
Subject: Re: Kconfig unmet dependency with RADIO_WL1273
Date: Mon, 29 Aug 2011 10:27:32 -0700 [thread overview]
Message-ID: <20110829102732.03f0f05d.rdunlap@xenotime.net> (raw)
In-Reply-To: <1314637358.2296.395.camel@cumari>
On Mon, 29 Aug 2011 20:02:38 +0300 Luciano Coelho wrote:
> Hi Matti,
>
> Johannes has just reported a problem in the Kconfig of radio-wl1273. It
> seems to select MFD_CORE, but if the platform doesn't support MFD, then
> MFD_SUPPORT won't be selected and this kind of warning will come out:
>
> warning: (OLPC_XO1_PM && OLPC_XO1_SCI && I2C_ISCH && GPIO_SCH && GPIO_RDC321X && RADIO_WL1273)
> selects MFD_CORE which has unmet direct dependencies (MFD_SUPPORT)
>
> I guess it must depend on MFD_SUPPORT, right? If that's the correct
> solution, the following patch should fix the problem:
>
> diff --git a/drivers/media/radio/Kconfig b/drivers/media/radio/Kconfig
> index 52798a1..e87f544 100644
> --- a/drivers/media/radio/Kconfig
> +++ b/drivers/media/radio/Kconfig
> @@ -425,7 +425,7 @@ config RADIO_TIMBERDALE
>
> config RADIO_WL1273
> tristate "Texas Instruments WL1273 I2C FM Radio"
> - depends on I2C && VIDEO_V4L2
> + depends on I2C && VIDEO_V4L2 && MFD_SUPPORT
> select MFD_CORE
> select MFD_WL1273_CORE
> select FW_LOADER
>
> The same problem is happening with other drivers too, so maybe there is
> a better solution to fix all problems at once. ;)
>
> Reported-by: Johannes Berg <johannes@sipsolutions.net>
Yes, it can depend on MFD_SUPPORT or it can select both
MFD_SUPPORT and MFD_CORE or we could do what Jean Delvare
suggested last December and combine the MFD_SUPPORT and MFD_CORE
symbols, like I2c does. I did a patch for that but never
posted it. It's below, but probably needs a good bit of
updating since this patch was made in January.
---
From: Randy Dunlap <rdunlap@xenotime.net>
Combine MFD_SUPPORT (which only enabled the remainder of the MFD
menu) and MFD_CORE. This allows other drivers to select MFD_CORE
without needing to also select MFD_SUPPORT, which fixes some
kconfig unmet dependency warnings. Modeled after I2C kconfig.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
---
drivers/mfd/Kconfig | 42 ++++--------------------------------------
1 file changed, 4 insertions(+), 38 deletions(-)
--- lnx-2637-rc5.orig/drivers/mfd/Kconfig
+++ lnx-2637-rc5/drivers/mfd/Kconfig
@@ -2,10 +2,9 @@
# Multifunction miscellaneous devices
#
-menuconfig MFD_SUPPORT
- bool "Multifunction device drivers"
+menuconfig MFD_CORE
+ tristate "Multifunction device drivers"
depends on HAS_IOMEM
- default y
help
Multifunction devices embed several functions (e.g. GPIOs,
touchscreens, keyboards, current regulators, power management chips,
@@ -18,16 +17,11 @@ menuconfig MFD_SUPPORT
This option alone does not add any kernel code.
-if MFD_SUPPORT
-
-config MFD_CORE
- tristate
- default n
+if MFD_CORE
config MFD_88PM860X
bool "Support Marvell 88PM8606/88PM8607"
depends on I2C=y && GENERIC_HARDIRQS
- select MFD_CORE
help
This supports for Marvell 88PM8606/88PM8607 Power Management IC.
This includes the I2C driver and the core APIs _only_, you have to
@@ -55,7 +49,6 @@ config MFD_SM501_GPIO
config MFD_ASIC3
bool "Support for Compaq ASIC3"
depends on GENERIC_HARDIRQS && GPIOLIB && ARM
- select MFD_CORE
---help---
This driver supports the ASIC3 multifunction chip found on many
PDAs (mainly iPAQ and HTC based ones)
@@ -63,7 +56,6 @@ config MFD_ASIC3
config MFD_SH_MOBILE_SDHI
bool "Support for SuperH Mobile SDHI"
depends on SUPERH || ARCH_SHMOBILE
- select MFD_CORE
select TMIO_MMC_DMA
---help---
This driver supports the SDHI hardware block found in many
@@ -71,7 +63,6 @@ config MFD_SH_MOBILE_SDHI
config MFD_DAVINCI_VOICECODEC
tristate
- select MFD_CORE
config MFD_DM355EVM_MSP
bool "DaVinci DM355 EVM microcontroller"
@@ -91,7 +82,6 @@ config HTC_EGPIO
config HTC_PASIC3
tristate "HTC PASIC3 LED/DS1WM chip support"
- select MFD_CORE
help
This core driver provides register access for the LED/DS1WM
chips labeled "AIC2" and "AIC3", found on HTC Blueangel and
@@ -133,7 +123,6 @@ config TPS65010
config TPS6507X
tristate "TPS6507x Power Management / Touch Screen chips"
- select MFD_CORE
depends on I2C
help
If you say yes here you get support for the TPS6507x series of
@@ -183,7 +172,6 @@ config TWL4030_POWER
config TWL4030_CODEC
bool
depends on TWL4030_CORE
- select MFD_CORE
default n
config TWL6030_PWM
@@ -198,7 +186,6 @@ config TWL6030_PWM
config MFD_STMPE
bool "Support STMicroelectronics STMPE"
depends on I2C=y && GENERIC_HARDIRQS
- select MFD_CORE
help
Support for the STMPE family of I/O Expanders from
STMicroelectronics.
@@ -221,7 +208,6 @@ config MFD_STMPE
config MFD_TC35892
bool "Support Toshiba TC35892"
depends on I2C=y && GENERIC_HARDIRQS
- select MFD_CORE
help
Support for the Toshiba TC35892 I/O Expander.
@@ -241,7 +227,6 @@ config TMIO_MMC_DMA
config MFD_T7L66XB
bool "Support Toshiba T7L66XB"
depends on ARM && HAVE_CLK
- select MFD_CORE
select MFD_TMIO
help
Support for Toshiba Mobile IO Controller T7L66XB
@@ -249,7 +234,6 @@ config MFD_T7L66XB
config MFD_TC6387XB
bool "Support Toshiba TC6387XB"
depends on ARM && HAVE_CLK
- select MFD_CORE
select MFD_TMIO
help
Support for Toshiba Mobile IO Controller TC6387XB
@@ -257,7 +241,6 @@ config MFD_TC6387XB
config MFD_TC6393XB
bool "Support Toshiba TC6393XB"
depends on GPIOLIB && ARM
- select MFD_CORE
select MFD_TMIO
help
Support for Toshiba Mobile IO Controller TC6393XB
@@ -286,7 +269,6 @@ config PMIC_ADP5520
config MFD_MAX8925
bool "Maxim Semiconductor MAX8925 PMIC Support"
depends on I2C=y && GENERIC_HARDIRQS
- select MFD_CORE
help
Say yes here to support for Maxim Semiconductor MAX8925. This is
a Power Management IC. This driver provies common support for
@@ -296,7 +278,6 @@ config MFD_MAX8925
config MFD_MAX8998
bool "Maxim Semiconductor MAX8998/National LP3974 PMIC Support"
depends on I2C=y && GENERIC_HARDIRQS
- select MFD_CORE
help
Say yes here to support for Maxim Semiconductor MAX8998 and
National Semiconductor LP3974. This is a Power Management IC.
@@ -306,7 +287,6 @@ config MFD_MAX8998
config MFD_WM8400
tristate "Support Wolfson Microelectronics WM8400"
- select MFD_CORE
depends on I2C
help
Support for the Wolfson Microelecronics WM8400 PMIC and audio
@@ -320,7 +300,6 @@ config MFD_WM831X
config MFD_WM831X_I2C
bool "Support Wolfson Microelectronics WM831x/2x PMICs with I2C"
- select MFD_CORE
select MFD_WM831X
depends on I2C=y && GENERIC_HARDIRQS
help
@@ -331,7 +310,6 @@ config MFD_WM831X_I2C
config MFD_WM831X_SPI
bool "Support Wolfson Microelectronics WM831x/2x PMICs with SPI"
- select MFD_CORE
select MFD_WM831X
depends on SPI_MASTER && GENERIC_HARDIRQS
help
@@ -405,7 +383,6 @@ config MFD_WM8350_I2C
config MFD_WM8994
bool "Support Wolfson Microelectronics WM8994"
- select MFD_CORE
depends on I2C=y && GENERIC_HARDIRQS
help
The WM8994 is a highly integrated hi-fi CODEC designed for
@@ -430,7 +407,6 @@ config MFD_MC13783
config MFD_MC13XXX
tristate "Support Freescale MC13783 and MC13892"
depends on SPI_MASTER
- select MFD_CORE
select MFD_MC13783
help
Support for the Freescale (Atlas) PMIC and audio CODECs
@@ -466,7 +442,6 @@ config ABX500_CORE
config AB3100_CORE
bool "ST-Ericsson AB3100 Mixed Signal Circuit core functions"
depends on I2C=y && ABX500_CORE
- select MFD_CORE
default y if ARCH_U300
help
Select this to enable the AB3100 Mixed Signal IC core
@@ -497,7 +472,6 @@ config EZX_PCAP
config AB8500_CORE
bool "ST-Ericsson AB8500 Mixed Signal Power Management chip"
depends on GENERIC_HARDIRQS && ABX500_CORE && SPI_MASTER && ARCH_U8500
- select MFD_CORE
help
Select this option to enable access to AB8500 power management
chip. This connects to U8500 either on the SSP/SPI bus
@@ -525,7 +499,6 @@ config AB8500_DEBUG
config AB3550_CORE
bool "ST-Ericsson AB3550 Mixed Signal Circuit core functions"
- select MFD_CORE
depends on I2C=y && GENERIC_HARDIRQS && ABX500_CORE
help
Select this to enable the AB3550 Mixed Signal IC core
@@ -539,7 +512,6 @@ config AB3550_CORE
config MFD_TIMBERDALE
tristate "Support for the Timberdale FPGA"
- select MFD_CORE
depends on PCI && GPIOLIB
---help---
This is the core driver for the timberdale FPGA. This device is a
@@ -551,14 +523,12 @@ config MFD_TIMBERDALE
config LPC_SCH
tristate "Intel SCH LPC"
depends on PCI
- select MFD_CORE
help
LPC bridge function of the Intel SCH provides support for
System Management Bus and General Purpose I/O.
config MFD_RDC321X
tristate "Support for RDC-R321x southbridge"
- select MFD_CORE
depends on PCI
help
Say yes here if you want to have support for the RDC R-321x SoC
@@ -567,7 +537,6 @@ config MFD_RDC321X
config MFD_JANZ_CMODIO
tristate "Support for Janz CMOD-IO PCI MODULbus Carrier Board"
- select MFD_CORE
depends on PCI
help
This is the core driver for the Janz CMOD-IO PCI MODULbus
@@ -577,7 +546,6 @@ config MFD_JANZ_CMODIO
config MFD_JZ4740_ADC
tristate "Support for the JZ4740 SoC ADC core"
- select MFD_CORE
depends on MACH_JZ4740
help
Say yes here if you want support for the ADC unit in the JZ4740 SoC.
@@ -586,7 +554,6 @@ config MFD_JZ4740_ADC
config MFD_TPS6586X
bool "TPS6586x Power Management chips"
depends on I2C=y && GPIOLIB && GENERIC_HARDIRQS
- select MFD_CORE
help
If you say yes here you get support for the TPS6586X series of
Power Management chips.
@@ -600,13 +567,12 @@ config MFD_TPS6586X
config MFD_VX855
tristate "Support for VIA VX855/VX875 integrated south bridge"
depends on PCI
- select MFD_CORE
help
Say yes here to enable support for various functions of the
VIA VX855/VX875 south bridge. You will need to enable the vx855_spi
and/or vx855_gpio drivers for this to do anything useful.
-endif # MFD_SUPPORT
+endif # MFD_CORE
menu "Multimedia Capabilities Port drivers"
depends on ARCH_SA1100
next prev parent reply other threads:[~2011-08-29 17:27 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-08-29 17:02 Kconfig unmet dependency with RADIO_WL1273 Luciano Coelho
2011-08-29 17:27 ` Randy Dunlap [this message]
2011-08-29 18:41 ` [PATCH] mfd: Combine MFD_SUPPORT and MFD_CORE Luciano Coelho
2011-08-29 18:41 ` Luciano Coelho
2011-08-29 18:54 ` Grant Likely
2011-08-29 18:54 ` Grant Likely
2011-08-31 16:18 ` Jean Delvare
2011-08-31 16:49 ` Arnd Bergmann
2011-09-02 11:54 ` Luciano Coelho
2011-09-02 12:37 ` Jean Delvare
2011-09-02 14:43 ` [PATCH 1/2] misc: remove CONFIG_MISC_DEVICES Arnd Bergmann
2011-09-05 12:41 ` Jean Delvare
2011-09-05 14:19 ` Arnd Bergmann
2011-09-05 14:27 ` Jean Delvare
2011-09-18 15:11 ` Randy Dunlap
2011-09-18 15:28 ` Greg KH
2011-09-18 18:45 ` Randy Dunlap
2011-09-19 8:47 ` Arnd Bergmann
2011-09-19 13:07 ` Greg KH
2011-09-19 15:14 ` Arnd Bergmann
2011-09-02 14:43 ` [PATCH 2/2] mfd: remove CONFIG_MFD_SUPPORT Arnd Bergmann
2011-09-05 13:09 ` Jean Delvare
2011-09-15 15:46 ` Samuel Ortiz
2011-09-02 15:49 ` [PATCH] mfd: Combine MFD_SUPPORT and MFD_CORE Arnd Bergmann
2011-09-15 17:16 ` Grant Likely
2011-09-19 15:06 ` Arnd Bergmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20110829102732.03f0f05d.rdunlap@xenotime.net \
--to=rdunlap@xenotime.net \
--cc=coelho@ti.com \
--cc=johannes@sipsolutions.net \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=matti.j.aaltonen@nokia.com \
--cc=mchehab@infradead.org \
--cc=sameo@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.