From: andrew@lunn.ch (Andrew Lunn)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] ARM: Kirkwood: Iomega ix2-200 DT support Signed-off-by: Alan M Butler <alanbutty12@gmail.com>
Date: Tue, 21 Aug 2012 07:10:01 +0200 [thread overview]
Message-ID: <20120821051001.GB30810@lunn.ch> (raw)
In-Reply-To: <2b8d12ce68911cc12c96dcdd60c3345b72d25780.1345472556.git.alanbutty12@gmail.com>
On Mon, Aug 20, 2012 at 03:29:07PM +0100, Alan M Butler wrote:
> Patch version 5.
> Add support for the Iomega ix2-200.
> Led's and buttons working as of kernel 3.6-rc2
>
> the 3 lines in the network interface do seem to be required as
> removing either causes the network card to not be able to reach
> the network (at least on my device).
>
> Product page:
> http://go.iomega.com/en/products/network-storage-desktop/storcenter-network-storage-solution/network-hard-drive-ix2-200-cloud/?partner=4735#tech_specsItem_tab
>
> Signed-off-by: Alan M Butler <alanbutty12@gmail.com>
>
> ---
> arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts | 105 +++++++++++++++++++++++++
> arch/arm/mach-kirkwood/Kconfig | 7 ++
> arch/arm/mach-kirkwood/Makefile | 1 +
> arch/arm/mach-kirkwood/Makefile.boot | 1 +
> arch/arm/mach-kirkwood/board-dt.c | 4 +
> arch/arm/mach-kirkwood/board-iomega_ix2_200.c | 57 ++++++++++++++
> arch/arm/mach-kirkwood/common.h | 6 ++
> 7 files changed, 181 insertions(+)
> create mode 100644 arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
> create mode 100644 arch/arm/mach-kirkwood/board-iomega_ix2_200.c
>
> diff --git a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
> new file mode 100644
> index 0000000..865aeec
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
> @@ -0,0 +1,105 @@
> +/dts-v1/;
> +
> +/include/ "kirkwood.dtsi"
> +
> +/ {
> + model = "Iomega StorCenter ix2-200";
> + compatible = "iom,ix2-200", "marvell,kirkwood-88f6281", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x10000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8 earlyprintk";
> + };
> +
> + ocp at f1000000 {
> + i2c at 11000 {
> + status = "okay";
> +
> + lm63: lm63 at 4c {
> + compatible = "national,lm63";
> + reg = <0x4c>;
> + };
> + };
> +
> + serial at 12000 {
> + clock-frequency = <200000000>;
> + status = "ok";
> + };
> +
> + nand at 3000000 {
> + status = "okay";
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x0000000 0x100000>;
> + read-only;
> + };
> +
> + partition at a0000 {
> + label = "env";
> + reg = <0xa0000 0x20000>;
> + read-only;
> + };
> +
> + partition at 100000 {
> + label = "uImage";
> + reg = <0x100000 0x300000>;
> + };
> +
> + partition at 400000 {
> + label = "uInitrd";
> + reg = <0x540000 0x1000000>;
> + };
> + };
> + sata at 80000 {
> + status = "okay";
> + nr-ports = <2>;
> + };
> +
> + };
> + gpio-leds {
> + compatible = "gpio-leds";
> +
> + power_led {
> + label = "status:white:power_led";
> + gpios = <&gpio0 16 0>;
> + linux,default-trigger = "default-on";
> + };
> + health_led1 {
> + label = "status:red:health_led";
> + gpios = <&gpio1 5 0>;
> + };
> + health_led2 {
> + label = "status:white:health_led";
> + gpios = <&gpio1 4 0>;
> + };
> + backup_led {
> + label = "status:blue:backup_led";
> + gpios = <&gpio0 15 0>;
> + };
> + };
> + gpio-keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + Power {
> + label = "Power Button";
> + linux,code = <116>;
> + gpios = <&gpio0 14 1>;
> + };
> + Reset {
> + label = "Reset Button";
> + linux,code = <0x198>;
> + gpios = <&gpio0 12 1>;
> + };
> + OTB {
> + label = "OTB Button";
> + linux,code = <133>;
> + gpios = <&gpio1 3 1>;
> + };
> + };
> +};
> diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
> index ca5c15a..bee8451 100644
> --- a/arch/arm/mach-kirkwood/Kconfig
> +++ b/arch/arm/mach-kirkwood/Kconfig
> @@ -195,6 +195,13 @@ config MACH_T5325
> Say 'Y' here if you want your kernel to support the
> HP t5325 Thin Client.
>
> +config MACH_IOMEGA_IX2_200_DT
> + bool "Iomega StorCenter ix2-200 (Flattened Device Tree)"
> + select ARCH_KIRKWOOD_DT
> + help
> + Say 'Y' here if you want your kernel to support the
> + Iomega StorCenter ix2-200 (Flattened Device Tree).
> +
> endmenu
>
> endif
> diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile
> index 055c85a..f5484dc 100644
> --- a/arch/arm/mach-kirkwood/Makefile
> +++ b/arch/arm/mach-kirkwood/Makefile
> @@ -28,3 +28,4 @@ obj-$(CONFIG_MACH_IB62X0_DT) += board-ib62x0.o
> obj-$(CONFIG_MACH_TS219_DT) += board-ts219.o tsx1x-common.o
> obj-$(CONFIG_MACH_GOFLEXNET_DT) += board-goflexnet.o
> obj-$(CONFIG_MACH_LSXL_DT) += board-lsxl.o
> +obj-$(CONFIG_MACH_IOMEGA_IX2_200_DT) += board-iomega_ix2_200.o
> diff --git a/arch/arm/mach-kirkwood/Makefile.boot b/arch/arm/mach-kirkwood/Makefile.boot
> index a571755..59b719d 100644
> --- a/arch/arm/mach-kirkwood/Makefile.boot
> +++ b/arch/arm/mach-kirkwood/Makefile.boot
> @@ -11,3 +11,4 @@ dtb-$(CONFIG_MACH_TS219_DT) += kirkwood-qnap-ts219.dtb
> dtb-$(CONFIG_MACH_GOFLEXNET_DT) += kirkwood-goflexnet.dtb
> dtb-$(CONFIG_MACH_LSXL_DT) += kirkwood-lschlv2.dtb
> dtb-$(CONFIG_MACH_LSXL_DT) += kirkwood-lsxhl.dtb
> +dtb-$(CONFIG_MACH_IOMEGA_IX2_200_DT) += kirkwood-iomega_ix2_200.dtb
> diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c
> index e4eb450..9b3ec17 100644
> --- a/arch/arm/mach-kirkwood/board-dt.c
> +++ b/arch/arm/mach-kirkwood/board-dt.c
> @@ -87,6 +87,9 @@ static void __init kirkwood_dt_init(void)
> if (of_machine_is_compatible("buffalo,lsxl"))
> lsxl_init();
>
> + if (of_machine_is_compatible("iom,ix2-200"))
> + iomega_ix2_200_init();
> +
> of_platform_populate(NULL, kirkwood_dt_match_table,
> kirkwood_auxdata_lookup, NULL);
> }
> @@ -100,6 +103,7 @@ static const char *kirkwood_dt_board_compat[] = {
> "qnap,ts219",
> "seagate,goflexnet",
> "buffalo,lsxl",
> + "iom,ix2-200",
> NULL
> };
>
> diff --git a/arch/arm/mach-kirkwood/board-iomega_ix2_200.c b/arch/arm/mach-kirkwood/board-iomega_ix2_200.c
> new file mode 100644
> index 0000000..158fb97
> --- /dev/null
> +++ b/arch/arm/mach-kirkwood/board-iomega_ix2_200.c
> @@ -0,0 +1,57 @@
> +/*
> + * arch/arm/mach-kirkwood/board-iomega_ix2_200.c
> + *
> + * Iomega StorCenter ix2-200
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/init.h>
> +#include <linux/platform_device.h>
> +#include <linux/mv643xx_eth.h>
> +#include <linux/ethtool.h>
> +#include <mach/kirkwood.h>
> +#include "common.h"
> +#include "mpp.h"
> +
> +static struct mv643xx_eth_platform_data iomega_ix2_200_ge00_data = {
> + .phy_addr = MV643XX_ETH_PHY_NONE,
> + .speed = SPEED_1000,
> + .duplex = DUPLEX_FULL,
> +};
> +
> +static unsigned int iomega_ix2_200_mpp_config[] __initdata = {
> + MPP12_GPIO, /* Reset Button */
> + MPP14_GPIO, /* Power Button */
> + MPP15_GPIO, /* Backup LED (blue) */
> + MPP16_GPIO, /* Power LED (white) */
> + MPP35_GPIO, /* OTB Button */
> + MPP36_GPIO, /* Rebuild LED (white) */
> + MPP37_GPIO, /* Health LED (red) */
> + MPP38_GPIO, /* SATA LED brightness control 1 */
> + MPP39_GPIO, /* SATA LED brightness control 2 */
> + MPP40_GPIO, /* Backup LED brightness control 1 */
> + MPP41_GPIO, /* Backup LED brightness control 2 */
> + MPP42_GPIO, /* Power LED brightness control 1 */
> + MPP43_GPIO, /* Power LED brightness control 2 */
> + MPP44_GPIO, /* Health LED brightness control 1 */
> + MPP45_GPIO, /* Health LED brightness control 2 */
> + MPP46_GPIO, /* Rebuild LED brightness control 1 */
> + MPP47_GPIO, /* Rebuild LED brightness control 2 */
> + 0
> +};
> +
> +void __init iomega_ix2_200_init(void)
> +{
> + /*
> + * Basic setup. Needs to be called early.
> + */
> + kirkwood_mpp_conf(iomega_ix2_200_mpp_config);
> +
> + kirkwood_ehci_init();
> +
> + kirkwood_ge01_init(&iomega_ix2_200_ge00_data);
> +}
> diff --git a/arch/arm/mach-kirkwood/common.h b/arch/arm/mach-kirkwood/common.h
> index 304dd1a..d5d4064 100644
> --- a/arch/arm/mach-kirkwood/common.h
> +++ b/arch/arm/mach-kirkwood/common.h
> @@ -94,6 +94,12 @@ void lsxl_init(void);
> static inline void lsxl_init(void) {};
> #endif
>
> +#ifdef CONFIG_MACH_IOMEGA_IX2_200_DT
> +void iomega_ix2_200_init(void);
> +#else
> +static inline void iomega_ix2_200_init(void) {};
> +#endif
> +
> /* early init functions not converted to fdt yet */
> char *kirkwood_id(void);
> void kirkwood_l2_init(void);
> --
> 1.7.9.5
>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Andrew
next prev parent reply other threads:[~2012-08-21 5:10 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <cover.1345472556.git.alanbutty12@gmail.com>
2012-08-20 14:29 ` [PATCH] ARM: Kirkwood: Iomega ix2-200 DT support Signed-off-by: Alan M Butler <alanbutty12@gmail.com> Alan M Butler
2012-08-21 5:10 ` Andrew Lunn [this message]
2012-08-28 18:10 ` [PATCH] ARM: Kirkwood: Iomega ix2-200 DT support Jason Cooper
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20120821051001.GB30810@lunn.ch \
--to=andrew@lunn.ch \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.