From: andrew@lunn.ch (Andrew Lunn)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 0/9] ARM: Kirkwood: Convert to pinctrl
Date: Wed, 24 Oct 2012 22:01:28 +0200 [thread overview]
Message-ID: <20121024200128.GY21046@lunn.ch> (raw)
In-Reply-To: <201210242006.55879.michael@walle.cc>
On Wed, Oct 24, 2012 at 08:06:55PM +0200, Michael Walle wrote:
> Hi Andrew,
>
> Am Mittwoch 24 Oktober 2012, 16:53:45 schrieb Andrew Lunn:
> > This patchset converts all DT kirkwood boards to using pinctrl.
> >
> > This patchset depends on an earlier patchset to allow the mvebu
> > pinctrl driver and gpio driver to be built for kirkwood.
> >
> > Only the TS219 conversion has been tested on hardware. The remaining
> > are compile tested. Before merging upstream, it would be good if the
> > others could be tested on hardware.
> >
> > This series along with the dependents can be found in:
>
> Unfortunately, this doesn't work for me. git bisect tells me its commit
> e01139ec82162f21875d09e820686aede4219695.
>
> I guess it has something to do with the lsxl_init calling gpio_set_value().
Humm.
I guess it is too early to use gpio. I don't think the gpio driver has
not been configured yet.
I need to think about this.
What happens if you comment out these two gpio_set_value calls?
Andrew
next prev parent reply other threads:[~2012-10-24 20:01 UTC|newest]
Thread overview: 58+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-10-24 14:53 [PATCH 0/9] ARM: Kirkwood: Convert to pinctrl Andrew Lunn
2012-10-24 14:53 ` [PATCH 1/9] ARM: Kirkwood: Convert TS219 " Andrew Lunn
2012-10-24 19:31 ` Thomas Petazzoni
2012-10-24 19:49 ` Sebastian Hesselbarth
2012-10-24 20:00 ` Thomas Petazzoni
2012-10-24 20:04 ` Andrew Lunn
2012-10-24 20:05 ` Thomas Petazzoni
2012-10-24 20:14 ` Sebastian Hesselbarth
2012-10-24 20:19 ` Thomas Petazzoni
2012-10-24 14:53 ` [PATCH 2/9] ARM: Kirkwood: Convert iConnect " Andrew Lunn
2012-10-24 14:53 ` [PATCH 3/9] ARM: Kirkwood: Convert dnskw " Andrew Lunn
2012-10-25 22:58 ` Jamie Lentin
2012-10-26 6:01 ` Andrew Lunn
2012-10-26 9:42 ` Jamie Lentin
2012-10-26 10:24 ` Andrew Lunn
2012-10-26 12:30 ` Jamie Lentin
2012-10-24 14:53 ` [PATCH 4/9] ARM: Kirkwood: Convert dockstar " Andrew Lunn
2012-10-24 14:53 ` [PATCH 5/9] ARM: Kirkwood: Convert dreamplug " Andrew Lunn
2012-10-24 14:53 ` [PATCH 6/9] ARM: Kirkwood: Convert GoFlex Net " Andrew Lunn
2012-10-26 17:28 ` Josh Coombs
2012-10-27 8:51 ` Andrew Lunn
2012-10-28 14:31 ` Josh Coombs
2012-10-24 14:53 ` [PATCH 7/9] ARM: Kirkwood: Convert ib62x0 " Andrew Lunn
2012-10-24 20:40 ` Simon Baatz
2012-10-24 14:53 ` [PATCH 8/9] ARM: Kirkwood: Convert lsxl boards " Andrew Lunn
2012-10-24 20:37 ` Michael Walle
2012-10-28 16:40 ` Michael Walle
2012-10-24 14:53 ` [PATCH 9/9] ARM: Kirkwood: Convert IX2-200 " Andrew Lunn
2012-10-24 20:04 ` Thomas Petazzoni
2012-10-24 20:20 ` Andrew Lunn
2012-10-24 20:29 ` Thomas Petazzoni
2012-10-24 15:29 ` [PATCH 0/9] ARM: Kirkwood: Convert " Josh Coombs
2012-10-24 15:35 ` Andrew Lunn
2012-10-24 19:26 ` Thomas Petazzoni
2012-10-24 18:06 ` Michael Walle
2012-10-24 20:01 ` Andrew Lunn [this message]
2012-10-24 20:47 ` Michael Walle
2012-10-24 21:33 ` Thomas Petazzoni
2012-10-25 5:46 ` Andrew Lunn
2012-10-25 6:28 ` Thomas Petazzoni
2012-10-25 7:39 ` Michael Walle
2012-10-25 7:43 ` Thomas Petazzoni
2012-10-25 20:19 ` Michael Walle
2012-10-26 18:06 ` Michael Walle
2012-10-26 18:45 ` Thomas Petazzoni
2012-10-26 20:17 ` Michael Walle
2012-10-27 8:59 ` Andrew Lunn
2012-10-25 22:57 ` Jamie Lentin
2012-10-28 16:57 ` Andrew Lunn
2012-10-28 18:17 ` Michael Walle
2012-10-28 19:50 ` Simon Baatz
2012-10-28 20:01 ` Andrew Lunn
2012-10-28 21:06 ` Jamie Lentin
2012-10-31 22:38 ` Josh Coombs
2012-11-07 16:13 ` [RFC PATCH 0/2] Kirkwood 98dx4122 pinctrl variant Valentin Longchamp
2012-11-07 17:36 ` Andrew Lunn
2012-11-07 16:13 ` [PATCH 1/2] ARM: support 98DX412x kirkwoods with pinctrl Valentin Longchamp
2012-11-07 16:13 ` [PATCH 2/2] ARM: convert the km_kirkwood board to pinctrl Valentin Longchamp
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20121024200128.GY21046@lunn.ch \
--to=andrew@lunn.ch \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.