All of lore.kernel.org
 help / color / mirror / Atom feed
From: Don Brace <don.brace@pmcs.com>
To: scott.teel@pmcs.com, Kevin.Barnett@pmcs.com,
	james.bottomley@parallels.com, hch@infradead.org,
	Justin.Lindley@pmcs.com, brace@pmcs.com
Cc: linux-scsi@vger.kernel.org
Subject: [PATCH v3 38/42] hpsa: use scsi host_no as hpsa controller number
Date: Tue, 17 Mar 2015 15:06:56 -0500	[thread overview]
Message-ID: <20150317200656.19856.53171.stgit@brunhilda> (raw)
In-Reply-To: <20150317200139.19856.87982.stgit@brunhilda>

From: Robert Elliott <elliott@hp.com>

Rather than numbering the hpsa controllers with an
incrementing 0..n value (e.g., that shows up in
/proc/interrupts), use the scsi midlayer
host_no (e.g. matching /sys/class/scsi_host/hostNN).

Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
---
 drivers/scsi/hpsa.c |  134 ++++++++++++++++++++++++++++-----------------------
 1 file changed, 74 insertions(+), 60 deletions(-)

diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c
index 4e34a62..511b7ab 100644
--- a/drivers/scsi/hpsa.c
+++ b/drivers/scsi/hpsa.c
@@ -324,32 +324,35 @@ static int check_for_unit_attention(struct ctlr_info *h,
 	switch (asc) {
 	case STATE_CHANGED:
 		dev_warn(&h->pdev->dev,
-			HPSA "%d: a state change detected, command retried\n",
-			h->ctlr);
+			"%s: a state change detected, command retried\n",
+			h->devname);
 		break;
 	case LUN_FAILED:
 		dev_warn(&h->pdev->dev,
-			HPSA "%d: LUN failure detected\n", h->ctlr);
+			"%s: LUN failure detected\n", h->devname);
 		break;
 	case REPORT_LUNS_CHANGED:
 		dev_warn(&h->pdev->dev,
-			HPSA "%d: report LUN data changed\n", h->ctlr);
+			"%s: report LUN data changed\n", h->devname);
 	/*
 	 * Note: this REPORT_LUNS_CHANGED condition only occurs on the external
 	 * target (array) devices.
 	 */
 		break;
 	case POWER_OR_RESET:
-		dev_warn(&h->pdev->dev, HPSA "%d: a power on "
-			"or device reset detected\n", h->ctlr);
+		dev_warn(&h->pdev->dev,
+			"%s: a power on or device reset detected\n",
+			h->devname);
 		break;
 	case UNIT_ATTENTION_CLEARED:
-		dev_warn(&h->pdev->dev, HPSA "%d: unit attention "
-		    "cleared by another initiator\n", h->ctlr);
+		dev_warn(&h->pdev->dev,
+			"%s: unit attention cleared by another initiator\n",
+			h->devname);
 		break;
 	default:
-		dev_warn(&h->pdev->dev, HPSA "%d: unknown "
-			"unit attention detected\n", h->ctlr);
+		dev_warn(&h->pdev->dev,
+			"%s: unknown unit attention detected\n",
+			h->devname);
 		break;
 	}
 	return 1;
@@ -4799,22 +4802,16 @@ static int hpsa_scan_finished(struct Scsi_Host *sh,
 	return finished;
 }
 
-static void hpsa_unregister_scsi(struct ctlr_info *h)
-{
-	/* we are being forcibly unloaded, and may not refuse. */
-	scsi_remove_host(h->scsi_host);
-	scsi_host_put(h->scsi_host);
-	h->scsi_host = NULL;
-}
-
-static int hpsa_register_scsi(struct ctlr_info *h)
+static int hpsa_scsi_host_alloc(struct ctlr_info *h)
 {
 	struct Scsi_Host *sh;
 	int error;
 
 	sh = scsi_host_alloc(&hpsa_driver_template, sizeof(h));
-	if (sh == NULL)
-		goto fail;
+	if (sh == NULL) {
+		dev_err(&h->pdev->dev, "scsi_host_alloc failed\n");
+		return -ENOMEM;
+	}
 
 	sh->io_port = 0;
 	sh->n_io_port = 0;
@@ -4826,7 +4823,6 @@ static int hpsa_register_scsi(struct ctlr_info *h)
 	sh->can_queue = h->nr_cmds - HPSA_NRESERVED_CMDS;
 	sh->cmd_per_lun = sh->can_queue;
 	sh->sg_tablesize = h->maxsgentries;
-	h->scsi_host = sh;
 	sh->hostdata[0] = (unsigned long) h;
 	sh->irq = h->intr[h->intr_mode];
 	sh->unique_id = sh->irq;
@@ -4835,24 +4831,24 @@ static int hpsa_register_scsi(struct ctlr_info *h)
 		dev_err(&h->pdev->dev,
 			"%s: scsi_init_shared_tag_map failed for controller %d\n",
 			__func__, h->ctlr);
-		goto fail_host_put;
-	}
-	error = scsi_add_host(sh, &h->pdev->dev);
-	if (error) {
-		dev_err(&h->pdev->dev, "%s: scsi_add_host failed for controller %d\n",
-			__func__, h->ctlr);
-		goto fail_host_put;
+			scsi_host_put(sh);
+			return error;
 	}
-	scsi_scan_host(sh);
+	h->scsi_host = sh;
 	return 0;
+}
 
- fail_host_put:
-	scsi_host_put(sh);
-	return error;
- fail:
-	dev_err(&h->pdev->dev, "%s: scsi_host_alloc"
-		" failed for controller %d\n", __func__, h->ctlr);
-	return -ENOMEM;
+static int hpsa_scsi_add_host(struct ctlr_info *h)
+{
+	int rv;
+
+	rv = scsi_add_host(h->scsi_host, &h->pdev->dev);
+	if (rv) {
+		dev_err(&h->pdev->dev, "scsi_add_host failed\n");
+		return rv;
+	}
+	scsi_scan_host(h->scsi_host);
+	return 0;
 }
 
 /*
@@ -7525,7 +7521,9 @@ static void hpsa_undo_allocations_after_kdump_soft_reset(struct ctlr_info *h)
 	hpsa_free_sg_chain_blocks(h);		/* init_one 6 */
 	hpsa_free_cmd_pool(h);			/* init_one 5 */
 	hpsa_free_irqs(h);			/* init_one 4 */
-	hpsa_free_pci_init(h);			/* init_one 3 */
+	scsi_host_put(h->scsi_host);		/* init_one 3 */
+	h->scsi_host = NULL;			/* init_one 3 */
+	hpsa_free_pci_init(h);			/* init_one 2_5 */
 	free_percpu(h->lockup_detected);	/* init_one 2 */
 	h->lockup_detected = NULL;		/* init_one 2 */
 	if (h->resubmit_wq) {
@@ -7829,9 +7827,15 @@ reinit_after_soft_reset:
 
 	rc = hpsa_pci_init(h);
 	if (rc)
-		goto clean2;	/* lockup, aer/h */
+		goto clean2;	/* lu, aer/h */
+
+	/* relies on h-> settings made by hpsa_pci_init, including
+	 * interrupt_mode h->intr */
+	rc = hpsa_scsi_host_alloc(h);
+	if (rc)
+		goto clean2_5;	/* pci, lu, aer/h */
 
-	sprintf(h->devname, HPSA "%d", number_of_controllers);
+	sprintf(h->devname, HPSA "%d", h->scsi_host->host_no);
 	h->ctlr = number_of_controllers;
 	number_of_controllers++;
 
@@ -7845,7 +7849,7 @@ reinit_after_soft_reset:
 			dac = 0;
 		} else {
 			dev_err(&pdev->dev, "no suitable DMA available\n");
-			goto clean3;	/* pci, lockup, aer/h */
+			goto clean3;	/* shost, pci, lu, aer/h */
 		}
 	}
 
@@ -7854,13 +7858,13 @@ reinit_after_soft_reset:
 
 	rc = hpsa_request_irqs(h, do_hpsa_intr_msi, do_hpsa_intr_intx);
 	if (rc)
-		goto clean3;	/* pci, lockup, aer/h */
+		goto clean3;	/* shost, pci, lu, aer/h */
 	rc = hpsa_alloc_cmd_pool(h);
 	if (rc)
-		goto clean4;	/* irq, pci, lockup, aer/h */
+		goto clean4;	/* irq, shost, pci, lu, aer/h */
 	rc = hpsa_alloc_sg_chain_blocks(h);
 	if (rc)
-		goto clean5;	/* cmd, irq, pci, lockup, aer/h */
+		goto clean5;	/* cmd, irq, shost, pci, lu, aer/h */
 	init_waitqueue_head(&h->scan_wait_queue);
 	init_waitqueue_head(&h->abort_cmd_wait_queue);
 	init_waitqueue_head(&h->abort_sync_wait_queue);
@@ -7869,11 +7873,16 @@ reinit_after_soft_reset:
 	pci_set_drvdata(pdev, h);
 	h->ndevices = 0;
 	h->hba_mode_enabled = 0;
-	h->scsi_host = NULL;
+
 	spin_lock_init(&h->devlock);
 	rc = hpsa_put_ctlr_into_performant_mode(h);
 	if (rc)
-		goto clean6;	/* sg, cmd, irq, pci, lockup, aer/h */
+		goto clean6; /* sg, cmd, irq, shost, pci, lu, aer/h */
+
+	/* hook into SCSI subsystem */
+	rc = hpsa_scsi_add_host(h);
+	if (rc)
+		goto clean7; /* perf, sg, cmd, irq, shost, pci, lu, aer/h */
 
 	/* create the resubmit workqueue */
 	h->rescan_ctlr_wq = hpsa_create_controller_wq(h, "rescan");
@@ -7928,7 +7937,7 @@ reinit_after_soft_reset:
 		rc = hpsa_kdump_soft_reset(h);
 		if (rc)
 			/* Neither hard nor soft reset worked, we're hosed. */
-			goto clean8;
+			goto clean9;
 
 		dev_info(&h->pdev->dev, "Board READY.\n");
 		dev_info(&h->pdev->dev,
@@ -7963,9 +7972,6 @@ reinit_after_soft_reset:
 	h->access.set_intr_mask(h, HPSA_INTR_ON);
 
 	hpsa_hba_inquiry(h);
-	rc = hpsa_register_scsi(h);	/* hook ourselves into SCSI subsystem */
-	if (rc)
-		goto clean8; /* wq, perf, sg, cmd, irq, pci, lockup, aer/h */
 
 	/* Monitor the controller for firmware lockups */
 	h->heartbeat_sample_interval = HEARTBEAT_SAMPLE_INTERVAL;
@@ -7977,20 +7983,23 @@ reinit_after_soft_reset:
 				h->heartbeat_sample_interval);
 	return 0;
 
-clean8: /* perf, sg, cmd, irq, pci, lockup, aer/h */
+clean9: /* wq, sh, perf, sg, cmd, irq, shost, pci, lu, aer/h */
 	kfree(h->hba_inquiry_data);
-clean7: /* perf, sg, cmd, irq, pci, lockup, aer/h */
+clean7: /* perf, sg, cmd, irq, shost, pci, lu, aer/h */
 	hpsa_free_performant_mode(h);
 	h->access.set_intr_mask(h, HPSA_INTR_OFF);
 clean6: /* sg, cmd, irq, pci, lockup, wq/aer/h */
 	hpsa_free_sg_chain_blocks(h);
-clean5: /* cmd, irq, pci, lockup, aer/h */
+clean5: /* cmd, irq, shost, pci, lu, aer/h */
 	hpsa_free_cmd_pool(h);
-clean4: /* irq, pci, lockup, aer/h */
+clean4: /* irq, shost, pci, lu, aer/h */
 	hpsa_free_irqs(h);
-clean3: /* pci, lockup, aer/h */
+clean3: /* shost, pci, lu, aer/h */
+	scsi_host_put(h->scsi_host);
+	h->scsi_host = NULL;
+clean2_5: /* pci, lu, aer/h */
 	hpsa_free_pci_init(h);
-clean2: /* lockup, aer/h */
+clean2: /* lu, aer/h */
 	if (h->lockup_detected) {
 		free_percpu(h->lockup_detected);
 		h->lockup_detected = NULL;
@@ -8089,17 +8098,22 @@ static void hpsa_remove_one(struct pci_dev *pdev)
 
 	hpsa_free_device_info(h);		/* scan */
 
-	hpsa_unregister_scsi(h);			/* init_one 9 */
-	kfree(h->hba_inquiry_data);			/* init_one 9 */
-	h->hba_inquiry_data = NULL;			/* init_one 9 */
+	kfree(h->hba_inquiry_data);			/* init_one 10 */
+	h->hba_inquiry_data = NULL;			/* init_one 10 */
+	if (h->scsi_host)
+		scsi_remove_host(h->scsi_host);		/* init_one 8 */
+	hpsa_free_ioaccel2_sg_chain_blocks(h);
 	hpsa_free_performant_mode(h);			/* init_one 7 */
 	hpsa_free_sg_chain_blocks(h);			/* init_one 6 */
 	hpsa_free_cmd_pool(h);				/* init_one 5 */
 
 	/* hpsa_free_irqs already called via hpsa_shutdown init_one 4 */
 
+	scsi_host_put(h->scsi_host);			/* init_one 3 */
+	h->scsi_host = NULL;				/* init_one 3 */
+
 	/* includes hpsa_disable_interrupt_mode - pci_init 2 */
-	hpsa_free_pci_init(h);				/* init_one 3 */
+	hpsa_free_pci_init(h);				/* init_one 2.5 */
 
 	free_percpu(h->lockup_detected);		/* init_one 2 */
 	h->lockup_detected = NULL;			/* init_one 2 */


  parent reply	other threads:[~2015-03-17 20:08 UTC|newest]

Thread overview: 54+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-03-17 20:02 [PATCH v3 00/42] hpsa updates Don Brace
2015-03-17 20:02 ` [PATCH v3 01/42] hpsa: add masked physical devices into h->dev[] array Don Brace
2015-03-17 20:02 ` [PATCH v3 02/42] hpsa: clean up host, channel, target, lun prints Don Brace
2015-03-17 20:02 ` [PATCH v3 03/42] hpsa: rework controller command submission Don Brace
2015-03-27 15:11   ` Tomas Henzl
2015-03-27 18:04     ` brace
2015-03-17 20:02 ` [PATCH v3 04/42] hpsa: clean up aborts Don Brace
2015-03-17 20:02 ` [PATCH v3 05/42] hpsa: decrement h->commands_outstanding in fail_all_outstanding_cmds Don Brace
2015-04-02 13:33   ` Tomas Henzl
2015-03-17 20:02 ` [PATCH v3 06/42] hpsa: hpsa decode sense data for io and tmf Don Brace
2015-03-17 20:03 ` [PATCH v3 07/42] hpsa: allow lockup detected to be viewed via sysfs Don Brace
2015-03-17 20:03 ` [PATCH v3 08/42] hpsa: make function names consistent Don Brace
2015-03-17 20:03 ` [PATCH v3 09/42] hpsa: factor out hpsa_init_cmd function Don Brace
2015-03-17 20:03 ` [PATCH v3 10/42] hpsa: do not ignore return value of hpsa_register_scsi Don Brace
2015-03-17 20:03 ` [PATCH v3 11/42] hpsa: try resubmitting down raid path on task set full Don Brace
2015-03-17 20:03 ` [PATCH v3 12/42] hpsa: factor out hpsa_ioaccel_submit function Don Brace
2015-03-17 20:03 ` [PATCH v3 13/42] hpsa: print accurate SSD Smart Path Enabled status Don Brace
2015-03-17 20:03 ` [PATCH v3 14/42] hpsa: use ioaccel2 path to submit IOs to physical drives in HBA mode Don Brace
2015-03-17 20:03 ` [PATCH v3 15/42] hpsa: Get queue depth from identify physical bmic for physical disks Don Brace
2015-03-17 20:03 ` [PATCH v3 16/42] hpsa: break hpsa_free_irqs_and_disable_msix into two functions Don Brace
2015-03-17 20:03 ` [PATCH v3 17/42] hpsa: clean up error handling Don Brace
2015-03-17 20:04 ` [PATCH v3 18/42] hpsa: refactor freeing of resources into more logical functions Don Brace
2015-03-17 20:04 ` [PATCH v3 19/42] hpsa: add ioaccel sg chaining for the ioaccel2 path Don Brace
2015-03-17 20:04 ` [PATCH v3 20/42] hpsa: add more ioaccel2 error handling, including underrun statuses Don Brace
2015-03-17 20:04 ` [PATCH v3 21/42] hpsa: do not check cmd_alloc return value - it cannnot return NULL Don Brace
2015-03-17 20:04 ` [PATCH v3 22/42] hpsa: correct return values from driver functions Don Brace
2015-03-17 20:04 ` [PATCH v3 23/42] hpsa: clean up driver init Don Brace
2015-03-17 20:04 ` [PATCH v3 24/42] hpsa: clean up some error reporting output in abort handler Don Brace
2015-03-17 20:04 ` [PATCH v3 25/42] hpsa: do not print ioaccel2 warning messages about unusual completions Don Brace
2015-03-17 20:04 ` [PATCH v3 26/42] hpsa: add support sending aborts to physical devices via the ioaccel2 path Don Brace
2015-03-17 20:04 ` [PATCH v3 27/42] hpsa: use helper routines for finishing commands Don Brace
2015-03-17 20:04 ` [PATCH v3 28/42] hpsa: don't return abort request until target is complete Don Brace
2015-03-17 20:05 ` [PATCH v3 29/42] hpsa: refactor and rework support for sending TEST_UNIT_READY Don Brace
2015-03-17 20:05 ` [PATCH v3 30/42] hpsa: performance tweak for hpsa_scatter_gather() Don Brace
2015-03-17 20:05 ` [PATCH v3 31/42] hpsa: call pci_release_regions after pci_disable_device Don Brace
2015-03-17 20:05 ` [PATCH v3 32/42] hpsa: skip free_irq calls if irqs are not allocated Don Brace
2015-03-17 20:05 ` [PATCH v3 33/42] hpsa: cleanup for init_one step 2 in kdump Don Brace
2015-03-17 20:05 ` [PATCH v3 34/42] hpsa: fix try_soft_reset error handling Don Brace
2015-03-17 20:05 ` [PATCH v3 35/42] hpsa: create workqueue after the driver is ready for use Don Brace
2015-03-17 20:06 ` [PATCH v3 36/42] hpsa: add interrupt number to /proc/interrupts interrupt name Don Brace
2015-03-17 20:06 ` [PATCH v3 37/42] hpsa: use block layer tag for command allocation Don Brace
2015-03-23 16:57   ` Tomas Henzl
     [not found]     ` <07F70BBF6832E34FA1C923241E8833AB486892F9@BBYEXM01.pmc-sierra.internal>
2015-03-25 18:33       ` Webb Scales
2015-03-26 12:47         ` Tomas Henzl
2015-03-26 14:38           ` Webb Scales
2015-03-26 15:10             ` Tomas Henzl
2015-03-26 15:18               ` Webb Scales
2015-04-10 15:13                 ` James Bottomley
2015-03-27 18:49     ` brace
2015-03-17 20:06 ` Don Brace [this message]
2015-03-17 20:07 ` [PATCH v3 39/42] hpsa: propagate the error code in hpsa_kdump_soft_reset Don Brace
2015-03-17 20:07 ` [PATCH v3 40/42] hpsa: cleanup reset Don Brace
2015-03-17 20:07 ` [PATCH v3 41/42] hpsa: change driver version Don Brace
2015-03-17 20:07 ` [PATCH v3 42/42] hpsa: add PMC to copyright Don Brace

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20150317200656.19856.53171.stgit@brunhilda \
    --to=don.brace@pmcs.com \
    --cc=Justin.Lindley@pmcs.com \
    --cc=Kevin.Barnett@pmcs.com \
    --cc=brace@pmcs.com \
    --cc=hch@infradead.org \
    --cc=james.bottomley@parallels.com \
    --cc=linux-scsi@vger.kernel.org \
    --cc=scott.teel@pmcs.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.