From: Tomi Valkeinen <tomi.valkeinen@ti.com>
To: dri-devel@lists.freedesktop.org, linux-omap@vger.kernel.org,
Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
Peter Ujfalusi <peter.ujfalusi@ti.com>,
Jyri Sarha <jsarha@ti.com>, Benoit Parrot <bparrot@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Subject: [RFC PATCH 0/6] drm/tidss: new display driver for TI's DSS6
Date: Thu, 31 May 2018 15:41:03 +0300 [thread overview]
Message-ID: <20180531124109.3209-1-tomi.valkeinen@ti.com> (raw)
Hi,
This is a new DRM driver for Texas Instruments' Keystone K2G SoC. K2G has DSS6
IP, which is related to the OMAP DSS IPs handled by the omapdrm driver. While
on higher level the DSS6 resembles the older DSS versions, the registers and
the internal pipelines differ a lot.
DSS6 IP on K2G is a "ultra-light" version, and has only a single plane and a
single output. The driver will also support future DSS versions, like DSS7 on
AM6 SoC, which supports multiple planes and outputs, so the driver already has
support for those. This is also the reason for the dispc abstraction layer.
The series is an RFC, as I want to include the DSS7 driver in the final
version. I hope that's ready in a week or two. I'm looking for comments on the
overall architecture.
Tomi
Peter Ujfalusi (1):
drm: Add support for extracting sync signal drive edge from videomode
Tomi Valkeinen (5):
dt-bindings: display/ti: add k2g-dss bindings
drm/tidss: add new driver for TI Keystone platforms
drm/panel: simple: add newhaven,nhd-4.3-480272ef-atxl LCD
ARM: dts: keystone-k2g: add DSS node
ARM: dts: keystone-k2g-evm: add LCD and HDMI displays
.../panel/newhaven,nhd-4.3-480272ef-atxl.txt | 7 +
.../bindings/display/ti/ti,k2g-dss.txt | 15 +
MAINTAINERS | 8 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/keystone-k2g-evm-lcd.dts | 80 +
arch/arm/boot/dts/keystone-k2g-evm.dts | 91 ++
arch/arm/boot/dts/keystone-k2g.dtsi | 21 +
drivers/gpu/drm/Kconfig | 2 +
drivers/gpu/drm/Makefile | 1 +
drivers/gpu/drm/drm_modes.c | 15 +-
drivers/gpu/drm/panel/panel-simple.c | 29 +
drivers/gpu/drm/tidss/Kconfig | 10 +
drivers/gpu/drm/tidss/Makefile | 11 +
drivers/gpu/drm/tidss/tidss_crtc.c | 464 ++++++
drivers/gpu/drm/tidss/tidss_crtc.h | 50 +
drivers/gpu/drm/tidss/tidss_dispc.h | 146 ++
drivers/gpu/drm/tidss/tidss_dispc6.c | 1397 +++++++++++++++++
drivers/gpu/drm/tidss/tidss_dispc6.h | 12 +
drivers/gpu/drm/tidss/tidss_dispc6_regs.h | 109 ++
drivers/gpu/drm/tidss/tidss_drv.c | 331 ++++
drivers/gpu/drm/tidss/tidss_drv.h | 41 +
drivers/gpu/drm/tidss/tidss_encoder.c | 101 ++
drivers/gpu/drm/tidss/tidss_encoder.h | 22 +
drivers/gpu/drm/tidss/tidss_irq.c | 193 +++
drivers/gpu/drm/tidss/tidss_irq.h | 25 +
drivers/gpu/drm/tidss/tidss_kms.c | 85 +
drivers/gpu/drm/tidss/tidss_kms.h | 14 +
drivers/gpu/drm/tidss/tidss_plane.c | 187 +++
drivers/gpu/drm/tidss/tidss_plane.h | 25 +
include/drm/drm_connector.h | 4 +
30 files changed, 3493 insertions(+), 4 deletions(-)
create mode 100644 Documentation/devicetree/bindings/display/panel/newhaven,nhd-4.3-480272ef-atxl.txt
create mode 100644 Documentation/devicetree/bindings/display/ti/ti,k2g-dss.txt
create mode 100644 arch/arm/boot/dts/keystone-k2g-evm-lcd.dts
create mode 100644 drivers/gpu/drm/tidss/Kconfig
create mode 100644 drivers/gpu/drm/tidss/Makefile
create mode 100644 drivers/gpu/drm/tidss/tidss_crtc.c
create mode 100644 drivers/gpu/drm/tidss/tidss_crtc.h
create mode 100644 drivers/gpu/drm/tidss/tidss_dispc.h
create mode 100644 drivers/gpu/drm/tidss/tidss_dispc6.c
create mode 100644 drivers/gpu/drm/tidss/tidss_dispc6.h
create mode 100644 drivers/gpu/drm/tidss/tidss_dispc6_regs.h
create mode 100644 drivers/gpu/drm/tidss/tidss_drv.c
create mode 100644 drivers/gpu/drm/tidss/tidss_drv.h
create mode 100644 drivers/gpu/drm/tidss/tidss_encoder.c
create mode 100644 drivers/gpu/drm/tidss/tidss_encoder.h
create mode 100644 drivers/gpu/drm/tidss/tidss_irq.c
create mode 100644 drivers/gpu/drm/tidss/tidss_irq.h
create mode 100644 drivers/gpu/drm/tidss/tidss_kms.c
create mode 100644 drivers/gpu/drm/tidss/tidss_kms.h
create mode 100644 drivers/gpu/drm/tidss/tidss_plane.c
create mode 100644 drivers/gpu/drm/tidss/tidss_plane.h
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
next reply other threads:[~2018-05-31 12:41 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-31 12:41 Tomi Valkeinen [this message]
2018-05-31 12:41 ` [RFC PATCH 1/6] drm: Add support for extracting sync signal drive edge from videomode Tomi Valkeinen
2018-05-31 12:41 ` [RFC PATCH 2/6] dt-bindings: display/ti: add k2g-dss bindings Tomi Valkeinen
2018-06-12 20:07 ` Rob Herring
2018-05-31 12:41 ` [RFC PATCH 3/6] drm/tidss: add new driver for TI Keystone platforms Tomi Valkeinen
2018-05-31 12:41 ` [RFC PATCH 4/6] drm/panel: simple: add newhaven, nhd-4.3-480272ef-atxl LCD Tomi Valkeinen
2018-05-31 12:41 ` [RFC PATCH 5/6] ARM: dts: keystone-k2g: add DSS node Tomi Valkeinen
2018-05-31 12:41 ` [RFC PATCH 6/6] ARM: dts: keystone-k2g-evm: add LCD and HDMI displays Tomi Valkeinen
2018-05-31 12:43 ` [RFC PATCH 0/6] drm/tidss: new display driver for TI's DSS6 Tomi Valkeinen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180531124109.3209-1-tomi.valkeinen@ti.com \
--to=tomi.valkeinen@ti.com \
--cc=bparrot@ti.com \
--cc=dri-devel@lists.freedesktop.org \
--cc=jsarha@ti.com \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-omap@vger.kernel.org \
--cc=peter.ujfalusi@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.