From: Stephan Gerhold <stephan@gerhold.net>
To: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Andy Gross <agross@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Ohad Ben-Cohen <ohad@wizery.com>,
Rajendra Nayak <rnayak@codeaurora.org>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-remoteproc@vger.kernel.org,
~postmarketos/upstreaming@lists.sr.ht,
Stephan Gerhold <stephan@gerhold.net>
Subject: [PATCH 00/10] Convert MSM8916 to use rpmpd/power domains
Date: Wed, 16 Sep 2020 12:41:25 +0200 [thread overview]
Message-ID: <20200916104135.25085-1-stephan@gerhold.net> (raw)
Newer platforms vote for necessary power domains through the power
domain subsystem. For historical reasons older platforms like MSM8916
or MSM8974 still control these as regulators.
This patch series adds the power domain definitions for MSM8916
to the rpmpd driver. Then, qcom_q6v5_mss and qcom_wcnss are updated
to use power domains for MSM8916/MSM8974. For compatibility with old
device trees (and for MSM8974) we still need to support using the
power domains through the regulator interface. This is implemented by
falling back to the regulators if requesting the power domains fails.
Finally, we remove the regulators that provide the power domains
(s1 and l3) entirely from the MSM8916 device tree: They should only
be used through the power domain subsystem from now on.
Stephan Gerhold (10):
soc: qcom: rpmpd: Rename MAX_8996_RPMPD_STATE to
MAX_CORNER_RPMPD_STATE
dt-bindings: power: rpmpd: Add MSM8916 RPM power domains
soc: qcom: rpmpd: Add MSM8916 power domains
arm64: dts: qcom: msm8916: Add RPM power domains
dt-bindings: remoteproc: qcom,q6v5: Deprecate regulators for PDs
remoteproc: qcom_q6v5_mss: Allow replacing regulators with power
domains
dt-bindings: remoteproc: qcom,wcnss: Deprecate regulators for PDs
remoteproc: qcom_wcnss: Allow replacing regulators with power domains
arm64: dts: qcom: msm8916: Use power domains for MSS/WCNSS remoteprocs
arm64: dts: qcom: msm8916-pm8916: Stop using s1/l3 as regulators
.../devicetree/bindings/power/qcom,rpmpd.yaml | 1 +
.../bindings/remoteproc/qcom,q6v5.txt | 12 +-
.../bindings/remoteproc/qcom,wcnss-pil.txt | 20 +++-
arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi | 10 --
.../boot/dts/qcom/msm8916-longcheer-l8150.dts | 10 --
arch/arm64/boot/dts/qcom/msm8916-pm8916.dtsi | 7 +-
.../qcom/msm8916-samsung-a2015-common.dtsi | 10 --
arch/arm64/boot/dts/qcom/msm8916.dtsi | 38 ++++++
drivers/remoteproc/qcom_q6v5_mss.c | 68 +++++++++--
drivers/remoteproc/qcom_wcnss.c | 109 +++++++++++++++---
drivers/soc/qcom/rpmpd.c | 25 +++-
include/dt-bindings/power/qcom-rpmpd.h | 7 ++
12 files changed, 242 insertions(+), 75 deletions(-)
--
2.28.0
next reply other threads:[~2020-09-16 17:48 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-09-16 10:41 Stephan Gerhold [this message]
2020-09-16 10:41 ` [PATCH 01/10] soc: qcom: rpmpd: Rename MAX_8996_RPMPD_STATE to MAX_CORNER_RPMPD_STATE Stephan Gerhold
2020-09-16 10:41 ` [PATCH 02/10] dt-bindings: power: rpmpd: Add MSM8916 RPM power domains Stephan Gerhold
2020-09-23 15:33 ` Rob Herring
2020-09-16 10:41 ` [PATCH 03/10] soc: qcom: rpmpd: Add MSM8916 " Stephan Gerhold
2020-09-16 10:41 ` [PATCH 04/10] arm64: dts: qcom: msm8916: Add RPM " Stephan Gerhold
2020-09-16 10:41 ` [PATCH 05/10] dt-bindings: remoteproc: qcom,q6v5: Deprecate regulators for PDs Stephan Gerhold
2020-09-23 15:35 ` Rob Herring
2020-09-23 15:51 ` Stephan Gerhold
2020-09-23 20:02 ` Rob Herring
2020-09-16 10:41 ` [PATCH 06/10] remoteproc: qcom_q6v5_mss: Allow replacing regulators with power domains Stephan Gerhold
2020-09-16 10:41 ` [PATCH 07/10] dt-bindings: remoteproc: qcom,wcnss: Deprecate regulators for PDs Stephan Gerhold
2020-09-16 10:41 ` [PATCH 08/10] remoteproc: qcom_wcnss: Allow replacing regulators with power domains Stephan Gerhold
2020-09-16 10:41 ` [PATCH 09/10] arm64: dts: qcom: msm8916: Use power domains for MSS/WCNSS remoteprocs Stephan Gerhold
2020-09-16 10:41 ` [PATCH 10/10] arm64: dts: qcom: msm8916-pm8916: Stop using s1/l3 as regulators Stephan Gerhold
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200916104135.25085-1-stephan@gerhold.net \
--to=stephan@gerhold.net \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-remoteproc@vger.kernel.org \
--cc=ohad@wizery.com \
--cc=rnayak@codeaurora.org \
--cc=robh+dt@kernel.org \
--cc=~postmarketos/upstreaming@lists.sr.ht \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.