From: Liam Beguin <liambeguin@gmail.com>
To: liambeguin@gmail.com, mturquette@baylibre.com, sboyd@kernel.org
Cc: linux-clk@vger.kernel.org, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org, robh+dt@kernel.org
Subject: [PATCH v4 2/3] clk: lmk04832: add support for digital delay
Date: Tue, 6 Apr 2021 20:53:29 -0400 [thread overview]
Message-ID: <20210407005330.2890430-3-liambeguin@gmail.com> (raw)
In-Reply-To: <20210407005330.2890430-1-liambeguin@gmail.com>
From: Liam Beguin <lvb@xiphos.com>
The digital delay allows outputs to be delayed from 8 to 1023 VCO
cycles. The delay step can be as small as half the period of the clock
distribution path. For example, a 3.2-GHz VCO frequency results in
156.25-ps steps. The digital delay value takes effect on the clock
output phase after a SYNC event.
This is required to support JESD204B subclass 1.
Signed-off-by: Liam Beguin <lvb@xiphos.com>
---
drivers/clk/clk-lmk04832.c | 321 ++++++++++++++++++++++++++++++++++++-
1 file changed, 315 insertions(+), 6 deletions(-)
diff --git a/drivers/clk/clk-lmk04832.c b/drivers/clk/clk-lmk04832.c
index 387a60fa2111..5393088fa68e 100644
--- a/drivers/clk/clk-lmk04832.c
+++ b/drivers/clk/clk-lmk04832.c
@@ -36,16 +36,24 @@
#define LMK04832_REG_CLKOUT_CTRL0(ch) (0x100 + (ch >> 1) * 8)
#define LMK04832_BIT_DCLK_DIV_LSB GENMASK(7, 0)
#define LMK04832_REG_CLKOUT_CTRL1(ch) (0x101 + (ch >> 1) * 8)
+#define LMK04832_BIT_DCLKX_Y_DDLY_LSB GENMASK(7, 0)
#define LMK04832_REG_CLKOUT_CTRL2(ch) (0x102 + (ch >> 1) * 8)
#define LMK04832_BIT_CLKOUTX_Y_PD BIT(7)
+#define LMK04832_BIT_DCLKX_Y_DDLY_PD BIT(4)
+#define LMK04832_BIT_DCLKX_Y_DDLY_MSB GENMASK(3, 2)
#define LMK04832_BIT_DCLK_DIV_MSB GENMASK(1, 0)
#define LMK04832_REG_CLKOUT_SRC_MUX(ch) (0x103 + (ch % 2) + (ch >> 1) * 8)
#define LMK04832_BIT_CLKOUT_SRC_MUX BIT(5)
#define LMK04832_REG_CLKOUT_CTRL3(ch) (0x103 + (ch >> 1) * 8)
#define LMK04832_BIT_DCLKX_Y_PD BIT(4)
#define LMK04832_BIT_DCLKX_Y_DCC BIT(2)
+#define LMK04832_BIT_DCLKX_Y_HS BIT(0)
#define LMK04832_REG_CLKOUT_CTRL4(ch) (0x104 + (ch >> 1) * 8)
#define LMK04832_BIT_SCLK_PD BIT(4)
+#define LMK04832_BIT_SCLKX_Y_DIS_MODE GENMASK(3, 2)
+#define LMK04832_REG_SCLKX_Y_ADLY(ch) (0x105 + (ch >> 1) * 8)
+#define LMK04832_REG_SCLKX_Y_DDLY(ch) (0x106 + (ch >> 1) * 8)
+#define LMK04832_BIT_SCLKX_Y_DDLY GENMASK(3, 0)
#define LMK04832_REG_CLKOUT_FMT(ch) (0x107 + (ch >> 1) * 8)
#define LMK04832_BIT_CLKOUT_FMT(ch) (ch % 2 ? 0xf0 : 0x0f)
#define LMK04832_VAL_CLKOUT_FMT_POWERDOWN 0x00
@@ -72,11 +80,19 @@
#define LMK04832_VAL_VCO_MUX_VCO1 0x01
#define LMK04832_VAL_VCO_MUX_EXT 0x02
#define LMK04832_REG_SYSREF_OUT 0x139
+#define LMK04832_BIT_SYSREF_REQ_EN BIT(6)
#define LMK04832_BIT_SYSREF_MUX GENMASK(1, 0)
+#define LMK04832_VAL_SYSREF_MUX_NORMAL_SYNC 0x00
+#define LMK04832_VAL_SYSREF_MUX_RECLK 0x01
+#define LMK04832_VAL_SYSREF_MUX_PULSER 0x02
#define LMK04832_VAL_SYSREF_MUX_CONTINUOUS 0x03
#define LMK04832_REG_SYSREF_DIV_MSB 0x13a
#define LMK04832_BIT_SYSREF_DIV_MSB GENMASK(4, 0)
#define LMK04832_REG_SYSREF_DIV_LSB 0x13b
+#define LMK04832_REG_SYSREF_DDLY_MSB 0x13c
+#define LMK04832_BIT_SYSREF_DDLY_MSB GENMASK(4, 0)
+#define LMK04832_REG_SYSREF_DDLY_LSB 0x13d
+#define LMK04832_REG_SYSREF_PULSE_CNT 0x13e
#define LMK04832_REG_FB_CTRL 0x13f
#define LMK04832_BIT_PLL2_RCLK_MUX BIT(7)
#define LMK04832_VAL_PLL2_RCLK_MUX_OSCIN 0x00
@@ -95,7 +111,15 @@
#define LMK04832_BIT_SYSREF_DDLY_PD BIT(1)
#define LMK04832_BIT_SYSREF_PLSR_PD BIT(0)
#define LMK04832_REG_SYNC 0x143
+#define LMK04832_BIT_SYNC_CLR BIT(7)
+#define LMK04832_BIT_SYNC_1SHOT_EN BIT(6)
+#define LMK04832_BIT_SYNC_POL BIT(5)
#define LMK04832_BIT_SYNC_EN BIT(4)
+#define LMK04832_BIT_SYNC_MODE GENMASK(1, 0)
+#define LMK04832_VAL_SYNC_MODE_OFF 0x00
+#define LMK04832_VAL_SYNC_MODE_ON 0x01
+#define LMK04832_VAL_SYNC_MODE_PULSER_PIN 0x02
+#define LMK04832_VAL_SYNC_MODE_PULSER_SPI 0x03
#define LMK04832_REG_SYNC_DIS 0x144
/* 0x146 - 0x14a CLKin Control */
@@ -127,6 +151,7 @@
#define LMK04832_BIT_PLL2_N_0 GENMASK(1, 0)
#define LMK04832_REG_PLL2_N_1 0x167
#define LMK04832_REG_PLL2_N_2 0x168
+#define LMK04832_REG_PLL2_DLD_CNT_MSB 0x16a
#define LMK04832_REG_PLL2_DLD_CNT_LSB 0x16b
#define LMK04832_REG_PLL2_LD 0x16e
#define LMK04832_BIT_PLL2_LD_MUX GENMASK(7, 3)
@@ -203,6 +228,11 @@ struct lmk_clkout {
*
* @dev: reference to a struct device, linked to the spi_device
* @regmap: struct regmap instance use to access the chip
+ * @sync_mode: operational mode for SYNC signal
+ * @sysref_mux: select SYSREF source
+ * @sysref_pulse_cnt: number of SYSREF pulses generated while not in continuous
+ * mode.
+ * @sysref_ddly: SYSREF digital delay value
* @oscin: PLL2 input clock
* @vco: reference to the internal VCO clock
* @sclk: reference to the internal sysref clock (SCLK)
@@ -217,6 +247,11 @@ struct lmk04832 {
struct device *dev;
struct regmap *regmap;
+ unsigned int sync_mode;
+ unsigned int sysref_mux;
+ unsigned int sysref_pulse_cnt;
+ unsigned int sysref_ddly;
+
struct clk *oscin;
struct clk_hw vco;
struct clk_hw sclk;
@@ -613,6 +648,212 @@ static int lmk04832_register_vco(struct lmk04832 *lmk)
return devm_clk_hw_register(lmk->dev, &lmk->vco);
}
+static int lmk04832_clkout_set_ddly(struct lmk04832 *lmk, int id)
+{
+ int dclk_div_adj[] = {0, 0, -2, -2, 0, 3, -1, 0};
+ unsigned int sclkx_y_ddly = 10;
+ unsigned int dclkx_y_ddly;
+ unsigned int dclkx_y_div;
+ unsigned int sysref_ddly;
+ unsigned int dclkx_y_hs;
+ unsigned int lsb, msb;
+ int ret;
+
+ ret = regmap_update_bits(lmk->regmap,
+ LMK04832_REG_CLKOUT_CTRL2(id),
+ LMK04832_BIT_DCLKX_Y_DDLY_PD,
+ FIELD_PREP(LMK04832_BIT_DCLKX_Y_DDLY_PD, 0));
+ if (ret)
+ return ret;
+
+ ret = regmap_read(lmk->regmap, LMK04832_REG_SYSREF_DDLY_LSB, &lsb);
+ if (ret)
+ return ret;
+
+ ret = regmap_read(lmk->regmap, LMK04832_REG_SYSREF_DDLY_MSB, &msb);
+ if (ret)
+ return ret;
+
+ sysref_ddly = FIELD_GET(LMK04832_BIT_SYSREF_DDLY_MSB, msb) << 8 | lsb;
+
+ ret = regmap_read(lmk->regmap, LMK04832_REG_CLKOUT_CTRL0(id), &lsb);
+ if (ret)
+ return ret;
+
+ ret = regmap_read(lmk->regmap, LMK04832_REG_CLKOUT_CTRL2(id), &msb);
+ if (ret)
+ return ret;
+
+ dclkx_y_div = FIELD_GET(LMK04832_BIT_DCLK_DIV_MSB, msb) << 8 | lsb;
+
+ ret = regmap_read(lmk->regmap, LMK04832_REG_CLKOUT_CTRL3(id), &lsb);
+ if (ret)
+ return ret;
+
+ dclkx_y_hs = FIELD_GET(LMK04832_BIT_DCLKX_Y_HS, lsb);
+
+ dclkx_y_ddly = sysref_ddly + 1 -
+ dclk_div_adj[dclkx_y_div < 6 ? dclkx_y_div : 7] -
+ dclkx_y_hs + sclkx_y_ddly;
+
+ if (dclkx_y_ddly < 7 || dclkx_y_ddly > 0x3fff) {
+ dev_err(lmk->dev, "DCLKX_Y_DDLY out of range (%d)\n",
+ dclkx_y_ddly);
+ return -EINVAL;
+ }
+
+ ret = regmap_write(lmk->regmap,
+ LMK04832_REG_SCLKX_Y_DDLY(id),
+ FIELD_GET(LMK04832_BIT_SCLKX_Y_DDLY, sclkx_y_ddly));
+ if (ret)
+ return ret;
+
+ ret = regmap_write(lmk->regmap, LMK04832_REG_CLKOUT_CTRL1(id),
+ FIELD_GET(0x00ff, dclkx_y_ddly));
+ if (ret)
+ return ret;
+
+ dev_dbg(lmk->dev, "clkout%02u: sysref_ddly=%u, dclkx_y_ddly=%u, "
+ "dclk_div_adj=%+d, dclkx_y_hs=%u, sclkx_y_ddly=%u\n",
+ id, sysref_ddly, dclkx_y_ddly,
+ dclk_div_adj[dclkx_y_div < 6 ? dclkx_y_div : 7],
+ dclkx_y_hs, sclkx_y_ddly);
+
+ return regmap_update_bits(lmk->regmap, LMK04832_REG_CLKOUT_CTRL2(id),
+ LMK04832_BIT_DCLKX_Y_DDLY_MSB,
+ FIELD_GET(0x0300, dclkx_y_ddly));
+}
+
+/** lmk04832_sclk_sync - Establish deterministic phase relationship between sclk
+ * and dclk
+ *
+ * @lmk: Reference to the lmk device
+ *
+ * The synchronization sequence:
+ * - in the datasheet https://www.ti.com/lit/ds/symlink/lmk04832.pdf, p.31
+ * (8.3.3.1 How to enable SYSREF)
+ * - Ti forum: https://e2e.ti.com/support/clock-and-timing/f/48/t/970972
+ *
+ * Returns 0 or negative errno.
+ */
+static int lmk04832_sclk_sync_sequence(struct lmk04832 *lmk)
+{
+ int ret;
+ int i;
+
+ /* 1. (optional) mute all sysref_outputs during synchronization */
+ /* 2. Enable and write device clock digital delay to applicable clocks */
+ ret = regmap_update_bits(lmk->regmap, LMK04832_REG_MAIN_PD,
+ LMK04832_BIT_SYSREF_DDLY_PD,
+ FIELD_PREP(LMK04832_BIT_SYSREF_DDLY_PD, 0));
+ if (ret)
+ return ret;
+
+ for (i = 0; i < lmk->clk_data->num; i += 2) {
+ ret = lmk04832_clkout_set_ddly(lmk, i);
+ if (ret)
+ return ret;
+ }
+
+ /*
+ * 3. Configure SYNC_MODE to SYNC_PIN and SYSREF_MUX to Normal SYNC,
+ * and clear SYSREF_REQ_EN (see 6.)
+ */
+ ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYSREF_OUT,
+ LMK04832_BIT_SYSREF_REQ_EN |
+ LMK04832_BIT_SYSREF_MUX,
+ FIELD_PREP(LMK04832_BIT_SYSREF_REQ_EN, 0) |
+ FIELD_PREP(LMK04832_BIT_SYSREF_MUX,
+ LMK04832_VAL_SYSREF_MUX_NORMAL_SYNC));
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYNC,
+ LMK04832_BIT_SYNC_MODE,
+ FIELD_PREP(LMK04832_BIT_SYNC_MODE,
+ LMK04832_VAL_SYNC_MODE_ON));
+ if (ret)
+ return ret;
+
+ /* 4. Clear SYNXC_DISx or applicable clocks and clear SYNC_DISSYSREF */
+ ret = regmap_write(lmk->regmap, LMK04832_REG_SYNC_DIS, 0x00);
+ if (ret)
+ return ret;
+
+ /*
+ * 5. If SCLKX_Y_DDLY != 0, Set SYSREF_CLR=1 for at least 15 clock
+ * distribution path cycles (VCO cycles), then back to 0. In
+ * PLL2-only use case, this will be complete in less than one SPI
+ * transaction. If SYSREF local digital delay is not used, this step
+ * can be skipped.
+ */
+ ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYNC,
+ LMK04832_BIT_SYNC_CLR,
+ FIELD_PREP(LMK04832_BIT_SYNC_CLR, 0x01));
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYNC,
+ LMK04832_BIT_SYNC_CLR,
+ FIELD_PREP(LMK04832_BIT_SYNC_CLR, 0x00));
+ if (ret)
+ return ret;
+
+ /*
+ * 6. Toggle SYNC_POL state between inverted and not inverted.
+ * If you use an external signal on the SYNC pin instead of toggling
+ * SYNC_POL, make sure that SYSREF_REQ_EN=0 so that the SYSREF_MUX
+ * does not shift into continuous SYSREF mode.
+ */
+ ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYNC,
+ LMK04832_BIT_SYNC_POL,
+ FIELD_PREP(LMK04832_BIT_SYNC_POL, 0x01));
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYNC,
+ LMK04832_BIT_SYNC_POL,
+ FIELD_PREP(LMK04832_BIT_SYNC_POL, 0x00));
+ if (ret)
+ return ret;
+
+ /* 7. Set all SYNC_DISx=1, including SYNC_DISSYSREF */
+ ret = regmap_write(lmk->regmap, LMK04832_REG_SYNC_DIS, 0xff);
+ if (ret)
+ return ret;
+
+ /* 8. Restore state of SYNC_MODE and SYSREF_MUX to desired values */
+ ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYSREF_OUT,
+ LMK04832_BIT_SYSREF_MUX,
+ FIELD_PREP(LMK04832_BIT_SYSREF_MUX,
+ lmk->sysref_mux));
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYNC,
+ LMK04832_BIT_SYNC_MODE,
+ FIELD_PREP(LMK04832_BIT_SYNC_MODE,
+ lmk->sync_mode));
+ if (ret)
+ return ret;
+
+ /*
+ * 9. (optional) if SCLKx_y_DIS_MODE was used to mute SYSREF outputs
+ * during the SYNC event, restore SCLKx_y_DIS_MODE=0 for active state,
+ * or set SYSREF_GBL_PD=0 if SCLKx_y_DIS_MODE is set to a conditional
+ * option.
+ */
+
+ /*
+ * 10. (optional) To reduce power consumption, after the synchronization
+ * event is complete, DCLKx_y_DDLY_PD=1 and SYSREF_DDLY_PD=1 disable the
+ * digital delay counters (which are only used immediately after the
+ * SYNC pulse to delay the output by some number of VCO counts).
+ */
+
+ return ret;
+}
+
static int lmk04832_sclk_is_enabled(struct clk_hw *hw)
{
struct lmk04832 *lmk = container_of(hw, struct lmk04832, sclk);
@@ -700,8 +941,16 @@ static int lmk04832_sclk_set_rate(struct clk_hw *hw, unsigned long rate,
if (ret)
return ret;
- return regmap_write(lmk->regmap, LMK04832_REG_SYSREF_DIV_LSB,
+ ret = regmap_write(lmk->regmap, LMK04832_REG_SYSREF_DIV_LSB,
FIELD_GET(0x00ff, sysref_div));
+ if (ret)
+ return ret;
+
+ ret = lmk04832_sclk_sync_sequence(lmk);
+ if (ret)
+ dev_err(lmk->dev, "SYNC sequence failed\n");
+
+ return ret;
}
static const struct clk_ops lmk04832_sclk_ops = {
@@ -730,18 +979,37 @@ static int lmk04832_register_sclk(struct lmk04832 *lmk)
ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYSREF_OUT,
LMK04832_BIT_SYSREF_MUX,
FIELD_PREP(LMK04832_BIT_SYSREF_MUX,
- LMK04832_VAL_SYSREF_MUX_CONTINUOUS));
+ lmk->sysref_mux));
+ if (ret)
+ return ret;
+
+ ret = regmap_write(lmk->regmap, LMK04832_REG_SYSREF_DDLY_LSB,
+ FIELD_GET(0x00ff, lmk->sysref_ddly));
+ if (ret)
+ return ret;
+
+ ret = regmap_write(lmk->regmap, LMK04832_REG_SYSREF_DDLY_MSB,
+ FIELD_GET(0x1f00, lmk->sysref_ddly));
+ if (ret)
+ return ret;
+
+ ret = regmap_write(lmk->regmap, LMK04832_REG_SYSREF_PULSE_CNT,
+ ilog2(lmk->sysref_pulse_cnt));
if (ret)
return ret;
ret = regmap_update_bits(lmk->regmap, LMK04832_REG_MAIN_PD,
+ LMK04832_BIT_SYSREF_DDLY_PD |
LMK04832_BIT_SYSREF_PLSR_PD,
- LMK04832_BIT_SYSREF_PLSR_PD);
+ FIELD_PREP(LMK04832_BIT_SYSREF_DDLY_PD, 0) |
+ FIELD_PREP(LMK04832_BIT_SYSREF_PLSR_PD, 0));
if (ret)
return ret;
- ret = regmap_update_bits(lmk->regmap, LMK04832_REG_SYNC,
- LMK04832_BIT_SYNC_EN, 0xff);
+ ret = regmap_write(lmk->regmap, LMK04832_REG_SYNC,
+ FIELD_PREP(LMK04832_BIT_SYNC_POL, 0) |
+ FIELD_PREP(LMK04832_BIT_SYNC_EN, 1) |
+ FIELD_PREP(LMK04832_BIT_SYNC_MODE, lmk->sync_mode));
if (ret)
return ret;
@@ -861,15 +1129,41 @@ static int lmk04832_dclk_set_rate(struct clk_hw *hw, unsigned long rate,
return ret;
}
+ /*
+ * While using Divide-by-2 or Divide-by-3 for DCLK_X_Y_DIV, SYNC
+ * procedure requires to first program Divide-by-4 and then back to
+ * Divide-by-2 or Divide-by-3 before doing SYNC.
+ */
+ if (dclk_div == 2 || dclk_div == 3) {
+ ret = regmap_update_bits(lmk->regmap,
+ LMK04832_REG_CLKOUT_CTRL2(dclk->id),
+ LMK04832_BIT_DCLK_DIV_MSB, 0x00);
+ if (ret)
+ return ret;
+
+ ret = regmap_write(lmk->regmap,
+ LMK04832_REG_CLKOUT_CTRL0(dclk->id), 0x04);
+ if (ret)
+ return ret;
+ }
+
ret = regmap_write(lmk->regmap, LMK04832_REG_CLKOUT_CTRL0(dclk->id),
FIELD_GET(0x0ff, dclk_div));
if (ret)
return ret;
- return regmap_update_bits(lmk->regmap,
+ ret = regmap_update_bits(lmk->regmap,
LMK04832_REG_CLKOUT_CTRL2(dclk->id),
LMK04832_BIT_DCLK_DIV_MSB,
FIELD_GET(0x300, dclk_div));
+ if (ret)
+ return ret;
+
+ ret = lmk04832_sclk_sync_sequence(lmk);
+ if (ret)
+ dev_err(lmk->dev, "SYNC sequence failed\n");
+
+ return ret;
};
static const struct clk_ops lmk04832_dclk_ops = {
@@ -1152,6 +1446,21 @@ static int lmk04832_probe(struct spi_device *spi)
device_property_read_u32(lmk->dev, "ti,vco-hz", &lmk->vco_rate);
+ lmk->sysref_ddly = 8;
+ device_property_read_u32(lmk->dev, "ti,sysref-ddly", &lmk->sysref_ddly);
+
+ lmk->sysref_mux = LMK04832_VAL_SYSREF_MUX_CONTINUOUS;
+ device_property_read_u32(lmk->dev, "ti,sysref-mux",
+ &lmk->sysref_mux);
+
+ lmk->sync_mode = LMK04832_VAL_SYNC_MODE_OFF;
+ device_property_read_u32(lmk->dev, "ti,sync-mode",
+ &lmk->sync_mode);
+
+ lmk->sysref_pulse_cnt = 4;
+ device_property_read_u32(lmk->dev, "ti,sysref-pulse-count",
+ &lmk->sysref_pulse_cnt);
+
for_each_child_of_node(lmk->dev->of_node, child) {
int reg;
--
2.30.1.489.g328c10930387
next prev parent reply other threads:[~2021-04-07 0:54 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-04-07 0:53 [PATCH v4 0/3] add support for the lmk04832 Liam Beguin
2021-04-07 0:53 ` [PATCH v4 1/3] clk: " Liam Beguin
2021-04-07 0:53 ` Liam Beguin [this message]
2021-04-07 0:53 ` [PATCH v4 3/3] dt-bindings: clock: add ti,lmk04832 bindings Liam Beguin
2021-04-08 20:13 ` Rob Herring
2021-04-09 1:28 ` Liam Beguin
2021-04-09 1:33 ` Liam Beguin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210407005330.2890430-3-liambeguin@gmail.com \
--to=liambeguin@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mturquette@baylibre.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.