From: Saeed Mahameed <saeed@kernel.org>
To: "David S. Miller" <davem@davemloft.net>,
Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org, Yevgeny Kliteynik <kliteyn@nvidia.com>,
Alex Vesker <valex@nvidia.com>,
Saeed Mahameed <saeedm@nvidia.com>
Subject: [net 03/11] net/mlx5: DR, Ignore modify TTL on RX if device doesn't support it
Date: Tue, 17 May 2022 23:34:19 -0700 [thread overview]
Message-ID: <20220518063427.123758-4-saeed@kernel.org> (raw)
In-Reply-To: <20220518063427.123758-1-saeed@kernel.org>
From: Yevgeny Kliteynik <kliteyn@nvidia.com>
When modifying TTL, packet's csum has to be recalculated.
Due to HW issue in ConnectX-5, csum recalculation for modify
TTL on RX is supported through a work-around that is specifically
enabled by configuration.
If the work-around isn't enabled, rather than adding an unsupported
action the modify TTL action on RX should be ignored.
Ignoring modify TTL action might result in zero actions, so in such
cases we will not convert the match STE to modify STE, as it is done
by FW in DMFS.
This patch fixes an issue where modify TTL action was ignored both
on RX and TX instead of only on RX.
Fixes: 4ff725e1d4ad ("net/mlx5: DR, Ignore modify TTL if device doesn't support it")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
---
.../mellanox/mlx5/core/steering/dr_action.c | 65 +++++++++++++------
.../mellanox/mlx5/core/steering/dr_ste_v0.c | 4 +-
2 files changed, 48 insertions(+), 21 deletions(-)
diff --git a/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_action.c b/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_action.c
index b52b539c8d2c..1383550f44c1 100644
--- a/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_action.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_action.c
@@ -530,6 +530,37 @@ static int dr_action_handle_cs_recalc(struct mlx5dr_domain *dmn,
return 0;
}
+static void dr_action_modify_ttl_adjust(struct mlx5dr_domain *dmn,
+ struct mlx5dr_ste_actions_attr *attr,
+ bool rx_rule,
+ bool *recalc_cs_required)
+{
+ *recalc_cs_required = false;
+
+ /* if device supports csum recalculation - no adjustment needed */
+ if (mlx5dr_ste_supp_ttl_cs_recalc(&dmn->info.caps))
+ return;
+
+ /* no adjustment needed on TX rules */
+ if (!rx_rule)
+ return;
+
+ if (!MLX5_CAP_ESW_FLOWTABLE(dmn->mdev, fdb_ipv4_ttl_modify)) {
+ /* Ignore the modify TTL action.
+ * It is always kept as last HW action.
+ */
+ attr->modify_actions--;
+ return;
+ }
+
+ if (dmn->type == MLX5DR_DOMAIN_TYPE_FDB)
+ /* Due to a HW bug on some devices, modifying TTL on RX flows
+ * will cause an incorrect checksum calculation. In such cases
+ * we will use a FW table to recalculate the checksum.
+ */
+ *recalc_cs_required = true;
+}
+
static void dr_action_print_sequence(struct mlx5dr_domain *dmn,
struct mlx5dr_action *actions[],
int last_idx)
@@ -650,8 +681,9 @@ int mlx5dr_actions_build_ste_arr(struct mlx5dr_matcher *matcher,
case DR_ACTION_TYP_MODIFY_HDR:
attr.modify_index = action->rewrite->index;
attr.modify_actions = action->rewrite->num_of_actions;
- recalc_cs_required = action->rewrite->modify_ttl &&
- !mlx5dr_ste_supp_ttl_cs_recalc(&dmn->info.caps);
+ if (action->rewrite->modify_ttl)
+ dr_action_modify_ttl_adjust(dmn, &attr, rx_rule,
+ &recalc_cs_required);
break;
case DR_ACTION_TYP_L2_TO_TNL_L2:
case DR_ACTION_TYP_L2_TO_TNL_L3:
@@ -732,12 +764,7 @@ int mlx5dr_actions_build_ste_arr(struct mlx5dr_matcher *matcher,
*new_hw_ste_arr_sz = nic_matcher->num_of_builders;
last_ste = ste_arr + DR_STE_SIZE * (nic_matcher->num_of_builders - 1);
- /* Due to a HW bug in some devices, modifying TTL on RX flows will
- * cause an incorrect checksum calculation. In this case we will
- * use a FW table to recalculate.
- */
- if (dmn->type == MLX5DR_DOMAIN_TYPE_FDB &&
- rx_rule && recalc_cs_required && dest_action) {
+ if (recalc_cs_required && dest_action) {
ret = dr_action_handle_cs_recalc(dmn, dest_action, &attr.final_icm_addr);
if (ret) {
mlx5dr_err(dmn,
@@ -1558,12 +1585,6 @@ dr_action_modify_check_is_ttl_modify(const void *sw_action)
return sw_field == MLX5_ACTION_IN_FIELD_OUT_IP_TTL;
}
-static bool dr_action_modify_ttl_ignore(struct mlx5dr_domain *dmn)
-{
- return !mlx5dr_ste_supp_ttl_cs_recalc(&dmn->info.caps) &&
- !MLX5_CAP_ESW_FLOWTABLE(dmn->mdev, fdb_ipv4_ttl_modify);
-}
-
static int dr_actions_convert_modify_header(struct mlx5dr_action *action,
u32 max_hw_actions,
u32 num_sw_actions,
@@ -1575,6 +1596,7 @@ static int dr_actions_convert_modify_header(struct mlx5dr_action *action,
const struct mlx5dr_ste_action_modify_field *hw_dst_action_info;
const struct mlx5dr_ste_action_modify_field *hw_src_action_info;
struct mlx5dr_domain *dmn = action->rewrite->dmn;
+ __be64 *modify_ttl_sw_action = NULL;
int ret, i, hw_idx = 0;
__be64 *sw_action;
__be64 hw_action;
@@ -1587,8 +1609,14 @@ static int dr_actions_convert_modify_header(struct mlx5dr_action *action,
action->rewrite->allow_rx = 1;
action->rewrite->allow_tx = 1;
- for (i = 0; i < num_sw_actions; i++) {
- sw_action = &sw_actions[i];
+ for (i = 0; i < num_sw_actions || modify_ttl_sw_action; i++) {
+ /* modify TTL is handled separately, as a last action */
+ if (i == num_sw_actions) {
+ sw_action = modify_ttl_sw_action;
+ modify_ttl_sw_action = NULL;
+ } else {
+ sw_action = &sw_actions[i];
+ }
ret = dr_action_modify_check_field_limitation(action,
sw_action);
@@ -1597,10 +1625,9 @@ static int dr_actions_convert_modify_header(struct mlx5dr_action *action,
if (!(*modify_ttl) &&
dr_action_modify_check_is_ttl_modify(sw_action)) {
- if (dr_action_modify_ttl_ignore(dmn))
- continue;
-
+ modify_ttl_sw_action = sw_action;
*modify_ttl = true;
+ continue;
}
/* Convert SW action to HW action */
diff --git a/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste_v0.c b/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste_v0.c
index 5a322335f204..2010d4ac6519 100644
--- a/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste_v0.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste_v0.c
@@ -420,7 +420,7 @@ dr_ste_v0_set_actions_tx(struct mlx5dr_domain *dmn,
* encapsulation. The reason for that is that we support
* modify headers for outer headers only
*/
- if (action_type_set[DR_ACTION_TYP_MODIFY_HDR]) {
+ if (action_type_set[DR_ACTION_TYP_MODIFY_HDR] && attr->modify_actions) {
dr_ste_v0_set_entry_type(last_ste, DR_STE_TYPE_MODIFY_PKT);
dr_ste_v0_set_rewrite_actions(last_ste,
attr->modify_actions,
@@ -513,7 +513,7 @@ dr_ste_v0_set_actions_rx(struct mlx5dr_domain *dmn,
}
}
- if (action_type_set[DR_ACTION_TYP_MODIFY_HDR]) {
+ if (action_type_set[DR_ACTION_TYP_MODIFY_HDR] && attr->modify_actions) {
if (dr_ste_v0_get_entry_type(last_ste) == DR_STE_TYPE_MODIFY_PKT)
dr_ste_v0_arr_init_next(&last_ste,
added_stes,
--
2.36.1
next prev parent reply other threads:[~2022-05-18 6:35 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-05-18 6:34 [pull request][net 00/11] mlx5 fixes 2022-05-17 Saeed Mahameed
2022-05-18 6:34 ` [net 01/11] net/mlx5: DR, Fix missing flow_source when creating multi-destination FW table Saeed Mahameed
2022-05-18 11:10 ` patchwork-bot+netdevbpf
2022-05-18 6:34 ` [net 02/11] net/mlx5: Initialize flow steering during driver probe Saeed Mahameed
2022-05-18 6:34 ` Saeed Mahameed [this message]
2022-05-18 6:34 ` [net 04/11] net/mlx5e: Wrap mlx5e_trap_napi_poll into rcu_read_lock Saeed Mahameed
2022-05-18 6:34 ` [net 05/11] net/mlx5e: Block rx-gro-hw feature in switchdev mode Saeed Mahameed
2022-05-18 6:34 ` [net 06/11] net/mlx5e: Properly block LRO when XDP is enabled Saeed Mahameed
2022-05-18 6:34 ` [net 07/11] net/mlx5e: Properly block HW GRO " Saeed Mahameed
2022-05-18 6:34 ` [net 08/11] net/mlx5e: Remove HW-GRO from reported features Saeed Mahameed
2022-05-18 6:34 ` [net 09/11] net/mlx5e: CT: Fix support for GRE tuples Saeed Mahameed
2022-05-18 6:34 ` [net 10/11] net/mlx5e: CT: Fix setting flow_source for smfs ct tuples Saeed Mahameed
2022-05-18 6:34 ` [net 11/11] net/mlx5: Drain fw_reset when removing device Saeed Mahameed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220518063427.123758-4-saeed@kernel.org \
--to=saeed@kernel.org \
--cc=davem@davemloft.net \
--cc=kliteyn@nvidia.com \
--cc=kuba@kernel.org \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=saeedm@nvidia.com \
--cc=valex@nvidia.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.