[PATCH 5.10.y-cip 03/24] arm64: dts: renesas: rzg2lc-smarc-som: Enable eMMC on SMARC platform

From: Biju Das <biju.das.jz@bp.renesas.com>
To: Pavel Machek <pavel@denx.de>
Cc: nobuhiro1.iwamatsu@toshiba.co.jp,
	Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>,
	Biju Das <biju.das.jz@bp.renesas.com>,
	cip-dev@lists.cip-project.org
Subject: [PATCH 5.10.y-cip 03/24] arm64: dts: renesas: rzg2lc-smarc-som: Enable eMMC on SMARC platform
Date: Tue,  2 Aug 2022 12:08:29 +0100	[thread overview]
Message-ID: <20220802110850.1496057-4-biju.das.jz@bp.renesas.com> (raw)
In-Reply-To: <20220802110850.1496057-1-biju.das.jz@bp.renesas.com>

commit 7ca0ce6478c6803c9f86e7366f5634de9c096207 upstream.

RZ/G2LC SoM has both 64 GB eMMC and microSD connected to SDHI0.

Both these interfaces are mutually exclusive and the SD0 device
selection is based on the XOR between GPIO_SD0_DEV_SEL and SW1[2]
switch position.

This patch sets GPIO_SD0_DEV_SEL to high in DT. Use the below switch
setting logic for device selection between eMMC and microSD slot
connected to SDHI0.

Set SW1[2] to position OFF for selecting eMMC
Set SW1[2] to position ON for selecting microSD

This patch enables eMMC on RZ/G2LC SMARC platform by default.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220117075130.6198-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
---
 .../boot/dts/renesas/rzg2lc-smarc-som.dtsi    | 142 ++++++++++++++++++
 1 file changed, 142 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/rzg2lc-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg2lc-smarc-som.dtsi
index e1d7a3a689c6..6ebda3724f2c 100644
--- a/arch/arm64/boot/dts/renesas/rzg2lc-smarc-som.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg2lc-smarc-som.dtsi
@@ -8,6 +8,16 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
 
+/* SW1[2] should be at OFF position to enable 64 GB eMMC */
+#define EMMC	1
+
+/*
+ * To enable uSD card on CN3,
+ * SW1[2] should be at ON position.
+ * Disable eMMC by setting "#define EMMC	0" above.
+ */
+#define SDHI	(!EMMC)
+
 / {
 	aliases {
 		ethernet0 = &eth0;
@@ -22,6 +32,36 @@ memory@48000000 {
 		/* first 128MB is reserved for secure area. */
 		reg = <0x0 0x48000000 0x0 0x38000000>;
 	};
+
+	reg_1p8v: regulator0 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator1 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vccq_sdhi0: regulator-vccq-sdhi0 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		states = <3300000 1>, <1800000 0>;
+		regulator-boot-on;
+		gpios = <&pinctrl RZG2L_GPIO(39, 0) GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+	};
 };
 
 &eth0 {
@@ -72,5 +112,107 @@ eth0_pins: eth0 {
 			 <RZG2L_PORT_PINMUX(26, 0, 1)>, /* ET0_RXD2 */
 			 <RZG2L_PORT_PINMUX(26, 1, 1)>; /* ET0_RXD3 */
 	};
+
+	gpio-sd0-pwr-en-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(18, 1) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "gpio_sd0_pwr_en";
+	};
+
+	/*
+	 * SD0 device selection is XOR between GPIO_SD0_DEV_SEL and SW1[2]
+	 * The below switch logic can be used to select the device between
+	 * eMMC and microSD, after setting GPIO_SD0_DEV_SEL to high in DT.
+	 * SW1[2] should be at OFF position to enable 64 GB eMMC
+	 * SW1[2] should be at position ON to enable uSD card CN3
+	 */
+	gpio-sd0-dev-sel-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(40, 2) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "gpio_sd0_dev_sel";
+	};
+
+	sdhi0_emmc_pins: sd0emmc {
+		sd0_emmc_data {
+			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3",
+			       "SD0_DATA4", "SD0_DATA5", "SD0_DATA6", "SD0_DATA7";
+			power-source = <1800>;
+		};
+
+		sd0_emmc_ctrl {
+			pins = "SD0_CLK", "SD0_CMD";
+			power-source = <1800>;
+		};
+
+		sd0_emmc_rst {
+			pins = "SD0_RST#";
+			power-source = <1800>;
+		};
+	};
+
+	sdhi0_pins: sd0 {
+		sd0_data {
+			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
+			power-source = <3300>;
+		};
+
+		sd0_ctrl {
+			pins = "SD0_CLK", "SD0_CMD";
+			power-source = <3300>;
+		};
+
+		sd0_mux {
+			pinmux = <RZG2L_PORT_PINMUX(18, 0, 1)>; /* SD0_CD */
+		};
+	};
+
+	sdhi0_pins_uhs: sd0_uhs {
+		sd0_data_uhs {
+			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
+			power-source = <1800>;
+		};
+
+		sd0_ctrl_uhs {
+			pins = "SD0_CLK", "SD0_CMD";
+			power-source = <1800>;
+		};
+
+		sd0_mux_uhs {
+			pinmux = <RZG2L_PORT_PINMUX(18, 0, 1)>; /* SD0_CD */
+		};
+	};
+};
+
+#if SDHI
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-1 = <&sdhi0_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&vccq_sdhi0>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+#endif
+
+#if EMMC
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_emmc_pins>;
+	pinctrl-1 = <&sdhi0_emmc_pins>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	fixed-emmc-driver-type = <1>;
+	status = "okay";
 };
+#endif
 
-- 
2.25.1


