All of lore.kernel.org
 help / color / mirror / Atom feed
From: Biju Das <biju.das.jz@bp.renesas.com>
To: Thierry Reding <thierry.reding@gmail.com>,
	Lee Jones <lee.jones@linaro.org>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Philipp Zabel <p.zabel@pengutronix.de>
Cc: "Biju Das" <biju.das.jz@bp.renesas.com>,
	"Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>,
	linux-pwm@vger.kernel.org, devicetree@vger.kernel.org,
	"Geert Uytterhoeven" <geert+renesas@glider.be>,
	"Chris Paterson" <Chris.Paterson2@renesas.com>,
	"Biju Das" <biju.das@bp.renesas.com>,
	"Prabhakar Mahadev Lad" <prabhakar.mahadev-lad.rj@bp.renesas.com>,
	linux-renesas-soc@vger.kernel.org
Subject: [PATCH v6 0/2] Add support for RZ/G2L GPT
Date: Mon,  5 Sep 2022 18:13:26 +0100	[thread overview]
Message-ID: <20220905171328.991367-1-biju.das.jz@bp.renesas.com> (raw)

RZ/G2L General PWM Timer (GPT) composed of 8 channels with 32-bit timer
(GPT32E). It supports the following functions
 * 32 bits × 8 channels
 * Up-counting or down-counting (saw waves) or up/down-counting
   (triangle waves) for each counter.
 * Clock sources independently selectable for each channel
 * Two I/O pins per channel
 * Two output compare/input capture registers per channel
 * For the two output compare/input capture registers of each channel,
   four registers are provided as buffer registers and are capable of
   operating as comparison registers when buffering is not in use.
 * In output compare operation, buffer switching can be at crests or
   troughs, enabling the generation of laterally asymmetric PWM waveforms.
 * Registers for setting up frame cycles in each channel (with capability
   for generating interrupts at overflow or underflow)
 * Generation of dead times in PWM operation
 * Synchronous starting, stopping and clearing counters for arbitrary
   channels
 * Starting, stopping, clearing and up/down counters in response to input
   level comparison
 * Starting, clearing, stopping and up/down counters in response to a
   maximum of four external triggers
 * Output pin disable function by dead time error and detected
   short-circuits between output pins
 * A/D converter start triggers can be generated (GPT32E0 to GPT32E3)
 * Enables the noise filter for input capture and external trigger
   operation

This patch series aims to add basic pwm support for RZ/G2L GPT driver
by creating separate logical channels for each IOs.

v5->v6:
 * Updated macros RZG2L_GTIOR_GTIOB_OUT_HI_END_TOGGLE_CMP_MATCH and
   RZG2L_GTIOR_GTIOB_OUT_LO_END_TOGGLE_CMP_MATCH with computation
   involving FIELD_PREP macro.
 * Removed struct rzg2l_gpt_phase and started using RZG2L_GTCCR macro
   for duty_offset.
 * replaced misnomer real_period->state_period.
 * Added handling for values >= (1024 << 32) for both period
   and duty cycle.
 * Added comments for pwm {en,dis}abled by bootloader during probe.
v4->v5:
 * Added Hardware manual details
 * Replaced the comment GTCNT->Counter
 * Removed the macros RZG2L_GPT_IO_PER_CHANNEL and chip.npwm directly
   used in probe.
 * Removed the unsed macro RZG2L_GTPR_MAX_VALUE
 * Added driver prefix for the type name and the variable.
 * Initialization of per_channel data moved from request->probe.
 * Updated clr parameter for rzg2l_gpt_modify for Start count.
 * Started using mutex and usage_count for handling shared
   period and prescalar for the 2 channels.
 * Updated the comment cycle->period.
 * Removed clk_disable from rzg2l_gpt_reset_assert_pm_disable()
 * Replaced pc->rzg2l_gpt.
 * Updated prescale calculation.
 * Moved pm_runtime_{get_sync,put} from {request,free}->{enable,disable}
 * Removed platform_set_drvdata as it is unused
 * Removed the variable pwm_enabled_by_bootloader 
 * Added dev_err_probe in various probe error path.
 * Added an error message, if devm_pwmchip_add fails.
v3->v4:
 * Changed the local variable type i from u16->u8 and prescaled_period_
   cycles from u64->u32 in calculate_prescale().
 * Replaced mul_u64_u64_div_u64()->mul_u64_u32_div()
 * Dropped the comma after the sentinel.
 * Add a variable to track pwm enabled by bootloader and added comments
   in probe().
 * Removed unnecessary rzg2l_gpt_reset_assert_pm_disable() from probe.
 * Replaced devm_clk_get()->devm_clk_get_prepared()
 * Removed devm_clk_get_optional_enabled()
v2->v3:
 * Added Rb tag from Rob for the bindings.
 * Updated limitation section
 * Added prefix "RZG2L_" for all macros
 * Modified prescale calculation
 * Removed pwm_set_chip_data
 * Updated comment related to modifying Mode and Prescaler
 * Updated setting of prescale value in rzg2l_gpt_config()
 * Removed else branch from rzg2l_gpt_get_state()
 * removed the err label from rzg2l_gpt_apply()
 * Added devm_clk_get_optional_enabled() to retain clk on status,
   in case bootloader turns on the clk of pwm.
 * Replaced devm_reset_control_get_exclusive->devm_reset_control_get_shared
   as single reset shared between 8 channels.
V1->v2:
 * Added '|' after 'description:' to preserve formatting.
 * Removed description for pwm_cells as it is common property.
 * Changed the reg size in example from 0xa4->0x100
 * Added Rb tag from Geert for bindings.
 * Added Limitations section
 * dropped "_MASK" from the define names.
 * used named initializer for struct phase
 * Added gpt_pwm_device into a flexible array member in rzg2l_gpt_chip
 * Revised the logic for prescale
 * Added .get_state callback
 * Improved error handling in rzg2l_gpt_apply
 * Removed .remove callback
 * Tested the driver with PWM_DEBUG enabled.

RFC->v1:
 * Added Description in binding patch
 * Removed comments from reg and clock
 * replaced rzg2l_gpt_write_mask()->rzg2l_gpt_modify()
 * Added rzg2l_gpt_read() and updated macros
 * Removed dtsi patches, will send it separately

RFC:
 * https://lore.kernel.org/linux-renesas-soc/20220430075915.5036-1-biju.das.jz@bp.renesas.com/T/#t

Biju Das (2):
  dt-bindings: pwm: Add RZ/G2L GPT binding
  pwm: Add support for RZ/G2L GPT

 .../bindings/pwm/renesas,rzg2l-gpt.yaml       | 129 ++++++
 drivers/pwm/Kconfig                           |  11 +
 drivers/pwm/Makefile                          |   1 +
 drivers/pwm/pwm-rzg2l-gpt.c                   | 409 ++++++++++++++++++
 4 files changed, 550 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pwm/renesas,rzg2l-gpt.yaml
 create mode 100644 drivers/pwm/pwm-rzg2l-gpt.c

-- 
2.25.1


             reply	other threads:[~2022-09-05 17:13 UTC|newest]

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-09-05 17:13 Biju Das [this message]
2022-09-05 17:13 ` [PATCH v6 1/2] dt-bindings: pwm: Add RZ/G2L GPT binding Biju Das
2022-09-05 17:13 ` [PATCH v6 2/2] pwm: Add support for RZ/G2L GPT Biju Das
2022-09-19  7:57   ` Uwe Kleine-König
2022-09-20 15:31     ` Biju Das
2022-09-20 15:53       ` Uwe Kleine-König
2022-09-20 17:00         ` Biju Das
2022-09-21 10:50           ` Biju Das
2022-09-21 13:35             ` Uwe Kleine-König
2022-09-21 13:46               ` Biju Das
2022-09-22  5:36                 ` Uwe Kleine-König
2022-09-22  6:15                   ` Biju Das
2022-09-24 10:53                     ` Biju Das
2022-09-24 13:42                       ` Uwe Kleine-König
2022-09-24 16:10                         ` Biju Das
2022-09-26  7:30                           ` Geert Uytterhoeven
2022-09-26  8:00                             ` Biju Das
2022-09-26 12:16                               ` Geert Uytterhoeven

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220905171328.991367-1-biju.das.jz@bp.renesas.com \
    --to=biju.das.jz@bp.renesas.com \
    --cc=Chris.Paterson2@renesas.com \
    --cc=biju.das@bp.renesas.com \
    --cc=devicetree@vger.kernel.org \
    --cc=geert+renesas@glider.be \
    --cc=krzk+dt@kernel.org \
    --cc=lee.jones@linaro.org \
    --cc=linux-pwm@vger.kernel.org \
    --cc=linux-renesas-soc@vger.kernel.org \
    --cc=p.zabel@pengutronix.de \
    --cc=prabhakar.mahadev-lad.rj@bp.renesas.com \
    --cc=robh+dt@kernel.org \
    --cc=thierry.reding@gmail.com \
    --cc=u.kleine-koenig@pengutronix.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.