From: Bartosz Golaszewski <brgl@bgdev.pl>
To: "Andy Gross" <agross@kernel.org>,
"Bjorn Andersson" <andersson@kernel.org>,
"Konrad Dybcio" <konrad.dybcio@somainline.org>,
"Greg Kroah-Hartman" <gregkh@linuxfoundation.org>,
"Jiri Slaby" <jirislaby@kernel.org>,
"Srinivas Kandagatla" <srinivas.kandagatla@linaro.org>,
"Vinod Koul" <vkoul@kernel.org>, "Alex Elder" <elder@kernel.org>,
"Ilpo Järvinen" <ilpo.jarvinen@linux.intel.com>
Cc: linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
linux-serial@vger.kernel.org,
Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Subject: [PATCH v2 15/15] tty: serial: qcom-geni-serial: add support for serial engine DMA
Date: Tue, 22 Nov 2022 11:21:25 +0100 [thread overview]
Message-ID: <20221122102125.142075-16-brgl@bgdev.pl> (raw)
In-Reply-To: <20221122102125.142075-1-brgl@bgdev.pl>
From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The qcom-geni-serial driver currently only works in SE FIFO mode. This
limits the UART speed to around 180 kB/s. In order to achieve higher
speeds we need to use SE DMA mode.
Keep the console port working in FIFO mode but extend the code to use DMA
for the high-speed port.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
drivers/tty/serial/qcom_geni_serial.c | 289 ++++++++++++++++++++++----
1 file changed, 247 insertions(+), 42 deletions(-)
diff --git a/drivers/tty/serial/qcom_geni_serial.c b/drivers/tty/serial/qcom_geni_serial.c
index 53d09da0854a..4aab92be162b 100644
--- a/drivers/tty/serial/qcom_geni_serial.c
+++ b/drivers/tty/serial/qcom_geni_serial.c
@@ -70,6 +70,8 @@
#define UART_START_TX 0x1
/* UART S_CMD OP codes */
#define UART_START_READ 0x1
+#define UART_PARAM 0x1
+#define UART_PARAM_RFR_OPEN BIT(7)
#define UART_OVERSAMPLING 32
#define STALE_TIMEOUT 16
@@ -95,9 +97,11 @@
/* We always configure 4 bytes per FIFO word */
#define BYTES_PER_FIFO_WORD 4
+#define DMA_RX_BUF_SIZE 2048
+
struct qcom_geni_device_data {
bool console;
- void (*handle_rx)(struct uart_port *uport, u32 bytes, bool drop);
+ enum geni_se_xfer_mode mode;
};
struct qcom_geni_private_data {
@@ -118,9 +122,11 @@ struct qcom_geni_serial_port {
u32 tx_fifo_depth;
u32 tx_fifo_width;
u32 rx_fifo_depth;
+ dma_addr_t tx_dma_addr;
+ dma_addr_t rx_dma_addr;
bool setup;
unsigned int baud;
- void *rx_fifo;
+ void *rx_buf;
u32 loopback;
bool brk;
@@ -552,18 +558,11 @@ static void handle_rx_console(struct uart_port *uport, u32 bytes, bool drop)
static void handle_rx_uart(struct uart_port *uport, u32 bytes, bool drop)
{
- struct tty_port *tport;
struct qcom_geni_serial_port *port = to_dev_port(uport);
- u32 num_bytes_pw = port->tx_fifo_width / BITS_PER_BYTE;
- u32 words = ALIGN(bytes, num_bytes_pw) / num_bytes_pw;
+ struct tty_port *tport = &uport->state->port;
int ret;
- tport = &uport->state->port;
- ioread32_rep(uport->membase + SE_GENI_RX_FIFOn, port->rx_fifo, words);
- if (drop)
- return;
-
- ret = tty_insert_flip_string(tport, port->rx_fifo, bytes);
+ ret = tty_insert_flip_string(tport, port->rx_buf, bytes);
if (ret != bytes) {
dev_err(uport->dev, "%s:Unable to push data ret %d_bytes %d\n",
__func__, ret, bytes);
@@ -578,7 +577,70 @@ static unsigned int qcom_geni_serial_tx_empty(struct uart_port *uport)
return !readl(uport->membase + SE_GENI_TX_FIFO_STATUS);
}
-static void qcom_geni_serial_start_tx(struct uart_port *uport)
+static void qcom_geni_serial_stop_tx_dma(struct uart_port *uport)
+{
+ struct qcom_geni_serial_port *port = to_dev_port(uport);
+ bool done;
+ u32 status;
+ u32 m_irq_en;
+
+ status = readl(uport->membase + SE_GENI_STATUS);
+ if (!(status & M_GENI_CMD_ACTIVE))
+ return;
+
+ if (port->rx_dma_addr) {
+ geni_se_tx_dma_unprep(&port->se, port->tx_dma_addr,
+ port->tx_remaining);
+ port->tx_dma_addr = (dma_addr_t)NULL;
+ port->tx_remaining = 0;
+ }
+
+ m_irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
+ writel(m_irq_en, uport->membase + SE_GENI_M_IRQ_EN);
+ geni_se_cancel_m_cmd(&port->se);
+
+ done = qcom_geni_serial_poll_bit(uport, SE_GENI_S_IRQ_STATUS,
+ S_CMD_CANCEL_EN, true);
+ if (!done) {
+ geni_se_abort_m_cmd(&port->se);
+ qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+ M_CMD_ABORT_EN, true);
+ writel(M_CMD_ABORT_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
+ }
+
+ writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
+}
+
+static void qcom_geni_serial_start_tx_dma(struct uart_port *uport)
+{
+ struct qcom_geni_serial_port *port = to_dev_port(uport);
+ struct circ_buf *xmit = &uport->state->xmit;
+ unsigned int xmit_size;
+ int ret;
+
+ if (port->tx_dma_addr)
+ return;
+
+ xmit_size = uart_circ_chars_pending(xmit);
+ if (xmit_size < WAKEUP_CHARS)
+ uart_write_wakeup(uport);
+
+ xmit_size = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
+
+ qcom_geni_serial_setup_tx(uport, xmit_size);
+
+ ret = geni_se_tx_dma_prep(&port->se, &xmit->buf[xmit->tail],
+ xmit_size, &port->tx_dma_addr);
+ if (ret) {
+ dev_err(uport->dev, "unable to start TX SE DMA: %d\n", ret);
+ qcom_geni_serial_stop_tx_dma(uport);
+ return;
+ }
+
+ port->tx_remaining = xmit_size;
+}
+
+static void qcom_geni_serial_start_tx_fifo(struct uart_port *uport)
{
u32 irq_en;
u32 status;
@@ -597,7 +659,7 @@ static void qcom_geni_serial_start_tx(struct uart_port *uport)
writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
}
-static void qcom_geni_serial_stop_tx(struct uart_port *uport)
+static void qcom_geni_serial_stop_tx_fifo(struct uart_port *uport)
{
u32 irq_en;
u32 status;
@@ -623,14 +685,13 @@ static void qcom_geni_serial_stop_tx(struct uart_port *uport)
writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
}
-static void qcom_geni_serial_handle_rx(struct uart_port *uport, bool drop)
+static void qcom_geni_serial_handle_rx_fifo(struct uart_port *uport, bool drop)
{
u32 status;
u32 word_cnt;
u32 last_word_byte_cnt;
u32 last_word_partial;
u32 total_bytes;
- struct qcom_geni_serial_port *port = to_dev_port(uport);
status = readl(uport->membase + SE_GENI_RX_FIFO_STATUS);
word_cnt = status & RX_FIFO_WC_MSK;
@@ -645,10 +706,10 @@ static void qcom_geni_serial_handle_rx(struct uart_port *uport, bool drop)
total_bytes += last_word_byte_cnt;
else
total_bytes += BYTES_PER_FIFO_WORD;
- port->dev_data->handle_rx(uport, total_bytes, drop);
+ handle_rx_console(uport, total_bytes, drop);
}
-static void qcom_geni_serial_stop_rx(struct uart_port *uport)
+static void qcom_geni_serial_stop_rx_fifo(struct uart_port *uport)
{
u32 irq_en;
u32 status;
@@ -678,7 +739,7 @@ static void qcom_geni_serial_stop_rx(struct uart_port *uport)
s_irq_status = readl(uport->membase + SE_GENI_S_IRQ_STATUS);
/* Flush the Rx buffer */
if (s_irq_status & S_RX_FIFO_LAST_EN)
- qcom_geni_serial_handle_rx(uport, true);
+ qcom_geni_serial_handle_rx_fifo(uport, true);
writel(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR);
status = readl(uport->membase + SE_GENI_STATUS);
@@ -686,7 +747,7 @@ static void qcom_geni_serial_stop_rx(struct uart_port *uport)
qcom_geni_serial_abort_rx(uport);
}
-static void qcom_geni_serial_start_rx(struct uart_port *uport)
+static void qcom_geni_serial_start_rx_fifo(struct uart_port *uport)
{
u32 irq_en;
u32 status;
@@ -694,7 +755,7 @@ static void qcom_geni_serial_start_rx(struct uart_port *uport)
status = readl(uport->membase + SE_GENI_STATUS);
if (status & S_GENI_CMD_ACTIVE)
- qcom_geni_serial_stop_rx(uport);
+ qcom_geni_serial_stop_rx_fifo(uport);
geni_se_setup_s_cmd(&port->se, UART_START_READ, 0);
@@ -707,6 +768,101 @@ static void qcom_geni_serial_start_rx(struct uart_port *uport)
writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
}
+static void qcom_geni_serial_stop_rx_dma(struct uart_port *uport)
+{
+ struct qcom_geni_serial_port *port = to_dev_port(uport);
+ u32 status;
+
+ status = readl(uport->membase + SE_GENI_STATUS);
+ if (!(status & S_GENI_CMD_ACTIVE))
+ return;
+
+ geni_se_cancel_s_cmd(&port->se);
+ qcom_geni_serial_poll_bit(uport, SE_GENI_S_IRQ_STATUS,
+ S_CMD_CANCEL_EN, true);
+
+ status = readl(uport->membase + SE_GENI_STATUS);
+ if (status & S_GENI_CMD_ACTIVE)
+ qcom_geni_serial_abort_rx(uport);
+
+ if (port->rx_dma_addr) {
+ geni_se_rx_dma_unprep(&port->se, port->rx_dma_addr,
+ DMA_RX_BUF_SIZE);
+ port->rx_dma_addr = (dma_addr_t)NULL;
+ }
+}
+
+static void qcom_geni_serial_start_rx_dma(struct uart_port *uport)
+{
+ struct qcom_geni_serial_port *port = to_dev_port(uport);
+ u32 status;
+ int ret;
+
+ status = readl(uport->membase + SE_GENI_STATUS);
+ if (status & S_GENI_CMD_ACTIVE)
+ qcom_geni_serial_stop_rx_dma(uport);
+
+ geni_se_setup_s_cmd(&port->se, UART_START_READ, UART_PARAM_RFR_OPEN);
+
+ ret = geni_se_rx_dma_prep(&port->se, port->rx_buf,
+ DMA_RX_BUF_SIZE,
+ &port->rx_dma_addr);
+ if (ret) {
+ dev_err(uport->dev, "unable to start RX SE DMA: %d\n", ret);
+ qcom_geni_serial_stop_rx_dma(uport);
+ }
+}
+
+static void qcom_geni_serial_handle_rx_dma(struct uart_port *uport, bool drop)
+{
+ struct qcom_geni_serial_port *port = to_dev_port(uport);
+ u32 status;
+ u32 rx_in;
+ int ret;
+
+ status = readl(uport->membase + SE_GENI_STATUS);
+ if (!(status & S_GENI_CMD_ACTIVE))
+ return;
+
+ if (!port->rx_dma_addr)
+ return;
+
+ geni_se_rx_dma_unprep(&port->se, port->rx_dma_addr, DMA_RX_BUF_SIZE);
+ port->rx_dma_addr = (dma_addr_t)NULL;
+
+ rx_in = readl(uport->membase + SE_DMA_RX_LEN_IN);
+ if (!rx_in) {
+ dev_warn(uport->dev, "serial engine reports 0 RX bytes in!\n");
+ return;
+ }
+
+ if (!drop)
+ handle_rx_uart(uport, rx_in, drop);
+
+ ret = geni_se_rx_dma_prep(&port->se, port->rx_buf,
+ DMA_RX_BUF_SIZE,
+ &port->rx_dma_addr);
+ if (ret) {
+ dev_err(uport->dev, "unable to start RX SE DMA: %d\n", ret);
+ qcom_geni_serial_stop_rx_dma(uport);
+ }
+}
+
+static void qcom_geni_serial_start_rx(struct uart_port *uport)
+{
+ uport->ops->start_rx(uport);
+}
+
+static void qcom_geni_serial_stop_rx(struct uart_port *uport)
+{
+ uport->ops->stop_rx(uport);
+}
+
+static void qcom_geni_serial_stop_tx(struct uart_port *uport)
+{
+ uport->ops->stop_tx(uport);
+}
+
static void qcom_geni_serial_send_chunk_fifo(struct uart_port *uport,
unsigned int chunk)
{
@@ -733,8 +889,8 @@ static void qcom_geni_serial_send_chunk_fifo(struct uart_port *uport,
}
}
-static void qcom_geni_serial_handle_tx(struct uart_port *uport, bool done,
- bool active)
+static void qcom_geni_serial_handle_tx_fifo(struct uart_port *uport,
+ bool done, bool active)
{
struct qcom_geni_serial_port *port = to_dev_port(uport);
struct circ_buf *xmit = &uport->state->xmit;
@@ -754,7 +910,7 @@ static void qcom_geni_serial_handle_tx(struct uart_port *uport, bool done,
/* All data has been transmitted and acknowledged as received */
if (!pending && !status && done) {
- qcom_geni_serial_stop_tx(uport);
+ qcom_geni_serial_stop_tx_fifo(uport);
goto out_write_wakeup;
}
@@ -797,12 +953,32 @@ static void qcom_geni_serial_handle_tx(struct uart_port *uport, bool done,
uart_write_wakeup(uport);
}
+static void qcom_geni_serial_handle_tx_dma(struct uart_port *uport)
+{
+ struct qcom_geni_serial_port *port = to_dev_port(uport);
+ struct circ_buf *xmit = &uport->state->xmit;
+
+ uart_xmit_advance(uport, port->tx_remaining);
+ geni_se_tx_dma_unprep(&port->se, port->tx_dma_addr, port->tx_remaining);
+ port->tx_dma_addr = (dma_addr_t)NULL;
+ port->tx_remaining = 0;
+
+ if (!uart_circ_empty(xmit))
+ qcom_geni_serial_start_tx_dma(uport);
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(uport);
+}
+
static irqreturn_t qcom_geni_serial_isr(int isr, void *dev)
{
u32 m_irq_en;
u32 m_irq_status;
u32 s_irq_status;
u32 geni_status;
+ u32 dma;
+ u32 dma_tx_status;
+ u32 dma_rx_status;
struct uart_port *uport = dev;
bool drop_rx = false;
struct tty_port *tport = &uport->state->port;
@@ -815,10 +991,15 @@ static irqreturn_t qcom_geni_serial_isr(int isr, void *dev)
m_irq_status = readl(uport->membase + SE_GENI_M_IRQ_STATUS);
s_irq_status = readl(uport->membase + SE_GENI_S_IRQ_STATUS);
+ dma_tx_status = readl(uport->membase + SE_DMA_TX_IRQ_STAT);
+ dma_rx_status = readl(uport->membase + SE_DMA_RX_IRQ_STAT);
geni_status = readl(uport->membase + SE_GENI_STATUS);
+ dma = readl(uport->membase + SE_GENI_DMA_MODE_EN);
m_irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
writel(m_irq_status, uport->membase + SE_GENI_M_IRQ_CLEAR);
writel(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR);
+ writel(dma_tx_status, uport->membase + SE_DMA_TX_IRQ_CLR);
+ writel(dma_rx_status, uport->membase + SE_DMA_RX_IRQ_CLR);
if (WARN_ON(m_irq_status & M_ILLEGAL_CMD_EN))
goto out_unlock;
@@ -828,10 +1009,6 @@ static irqreturn_t qcom_geni_serial_isr(int isr, void *dev)
tty_insert_flip_char(tport, 0, TTY_OVERRUN);
}
- if (m_irq_status & m_irq_en & (M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN))
- qcom_geni_serial_handle_tx(uport, m_irq_status & M_CMD_DONE_EN,
- geni_status & M_GENI_CMD_ACTIVE);
-
if (s_irq_status & (S_GP_IRQ_0_EN | S_GP_IRQ_1_EN)) {
if (s_irq_status & S_GP_IRQ_0_EN)
uport->icount.parity++;
@@ -841,8 +1018,35 @@ static irqreturn_t qcom_geni_serial_isr(int isr, void *dev)
port->brk = true;
}
- if (s_irq_status & (S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN))
- qcom_geni_serial_handle_rx(uport, drop_rx);
+ if (dma) {
+ if (dma_tx_status & TX_DMA_DONE)
+ qcom_geni_serial_handle_tx_dma(uport);
+
+ if (dma_rx_status) {
+ if (dma_rx_status & RX_RESET_DONE)
+ goto out_unlock;
+
+ if (dma_rx_status & RX_DMA_PARITY_ERR) {
+ uport->icount.parity++;
+ drop_rx = true;
+ }
+
+ if (dma_rx_status & RX_DMA_BREAK)
+ uport->icount.brk++;
+
+ if (dma_rx_status & (RX_DMA_DONE | RX_EOT))
+ qcom_geni_serial_handle_rx_dma(uport, drop_rx);
+ }
+ } else {
+ if (m_irq_status & m_irq_en &
+ (M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN))
+ qcom_geni_serial_handle_tx_fifo(uport,
+ m_irq_status & M_CMD_DONE_EN,
+ geni_status & M_GENI_CMD_ACTIVE);
+
+ if (s_irq_status & (S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN))
+ qcom_geni_serial_handle_rx_fifo(uport, drop_rx);
+ }
out_unlock:
uart_unlock_and_check_sysrq(uport);
@@ -912,7 +1116,7 @@ static int qcom_geni_serial_port_setup(struct uart_port *uport)
geni_se_config_packing(&port->se, BITS_PER_BYTE, BYTES_PER_FIFO_WORD,
false, true, true);
geni_se_init(&port->se, UART_RX_WM, port->rx_fifo_depth - 2);
- geni_se_select_mode(&port->se, GENI_SE_FIFO);
+ geni_se_select_mode(&port->se, port->dev_data->mode);
port->setup = true;
return 0;
@@ -1310,10 +1514,10 @@ static void qcom_geni_serial_pm(struct uart_port *uport,
static const struct uart_ops qcom_geni_console_pops = {
.tx_empty = qcom_geni_serial_tx_empty,
- .stop_tx = qcom_geni_serial_stop_tx,
- .start_tx = qcom_geni_serial_start_tx,
- .stop_rx = qcom_geni_serial_stop_rx,
- .start_rx = qcom_geni_serial_start_rx,
+ .stop_tx = qcom_geni_serial_stop_tx_fifo,
+ .start_tx = qcom_geni_serial_start_tx_fifo,
+ .stop_rx = qcom_geni_serial_stop_rx_fifo,
+ .start_rx = qcom_geni_serial_start_rx_fifo,
.set_termios = qcom_geni_serial_set_termios,
.startup = qcom_geni_serial_startup,
.request_port = qcom_geni_serial_request_port,
@@ -1331,9 +1535,10 @@ static const struct uart_ops qcom_geni_console_pops = {
static const struct uart_ops qcom_geni_uart_pops = {
.tx_empty = qcom_geni_serial_tx_empty,
- .stop_tx = qcom_geni_serial_stop_tx,
- .start_tx = qcom_geni_serial_start_tx,
- .stop_rx = qcom_geni_serial_stop_rx,
+ .stop_tx = qcom_geni_serial_stop_tx_dma,
+ .start_tx = qcom_geni_serial_start_tx_dma,
+ .start_rx = qcom_geni_serial_start_rx_dma,
+ .stop_rx = qcom_geni_serial_stop_rx_dma,
.set_termios = qcom_geni_serial_set_termios,
.startup = qcom_geni_serial_startup,
.request_port = qcom_geni_serial_request_port,
@@ -1402,9 +1607,9 @@ static int qcom_geni_serial_probe(struct platform_device *pdev)
port->tx_fifo_width = DEF_FIFO_WIDTH_BITS;
if (!data->console) {
- port->rx_fifo = devm_kcalloc(uport->dev,
- port->rx_fifo_depth, sizeof(u32), GFP_KERNEL);
- if (!port->rx_fifo)
+ port->rx_buf = devm_kzalloc(uport->dev,
+ DMA_RX_BUF_SIZE, GFP_KERNEL);
+ if (!port->rx_buf)
return -ENOMEM;
}
@@ -1528,12 +1733,12 @@ static int __maybe_unused qcom_geni_serial_sys_resume(struct device *dev)
static const struct qcom_geni_device_data qcom_geni_console_data = {
.console = true,
- .handle_rx = handle_rx_console,
+ .mode = GENI_SE_FIFO,
};
static const struct qcom_geni_device_data qcom_geni_uart_data = {
.console = false,
- .handle_rx = handle_rx_uart,
+ .mode = GENI_SE_DMA,
};
static const struct dev_pm_ops qcom_geni_serial_pm_ops = {
--
2.37.2
prev parent reply other threads:[~2022-11-22 10:24 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-11-22 10:21 [PATCH v2 00/15] serial: qcom-geni-serial: implement support for SE DMA Bartosz Golaszewski
2022-11-22 10:21 ` [PATCH v2 01/15] tty: serial: qcom-geni-serial: drop unneeded forward definitions Bartosz Golaszewski
2022-11-22 10:21 ` [PATCH v2 02/15] tty: serial: qcom-geni-serial: remove unused symbols Bartosz Golaszewski
2022-11-22 10:21 ` [PATCH v2 03/15] tty: serial: qcom-geni-serial: align #define values Bartosz Golaszewski
2022-11-22 10:21 ` [PATCH v2 04/15] tty: serial: qcom-geni-serial: improve the to_dev_port() macro Bartosz Golaszewski
2022-11-22 10:21 ` [PATCH v2 05/15] tty: serial: qcom-geni-serial: remove stray newlines Bartosz Golaszewski
2022-11-22 10:21 ` [PATCH v2 06/15] tty: serial: qcom-geni-serial: refactor qcom_geni_serial_isr() Bartosz Golaszewski
2022-11-22 10:21 ` [PATCH v2 07/15] tty: serial: qcom-geni-serial: remove unneeded tabs Bartosz Golaszewski
2022-11-22 10:21 ` [PATCH v2 08/15] tty: serial: qcom-geni-serial: refactor qcom_geni_serial_handle_tx() Bartosz Golaszewski
2022-11-22 10:21 ` [PATCH v2 09/15] tty: serial: qcom-geni-serial: drop the return value from handle_rx Bartosz Golaszewski
2022-11-22 10:21 ` [PATCH v2 10/15] tty: serial: qcom-geni-serial: use of_device_id data Bartosz Golaszewski
2022-11-22 10:21 ` [PATCH v2 11/15] tty: serial: qcom-geni-serial: stop operations in progress at shutdown Bartosz Golaszewski
2022-11-22 10:21 ` [PATCH v2 12/15] tty: serial: provide devm_uart_add_one_port() Bartosz Golaszewski
2022-11-22 16:58 ` Greg Kroah-Hartman
2022-11-23 15:30 ` Bartosz Golaszewski
2022-11-22 10:21 ` [PATCH v2 13/15] tty: serial: qcom-geni-serial: use devres for uart port management Bartosz Golaszewski
2022-11-22 10:21 ` [PATCH v2 14/15] soc: qcom-geni-se: add more symbol definitions Bartosz Golaszewski
2022-11-22 10:21 ` Bartosz Golaszewski [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20221122102125.142075-16-brgl@bgdev.pl \
--to=brgl@bgdev.pl \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=bartosz.golaszewski@linaro.org \
--cc=elder@kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=ilpo.jarvinen@linux.intel.com \
--cc=jirislaby@kernel.org \
--cc=konrad.dybcio@somainline.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=srinivas.kandagatla@linaro.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.