From: Manorit Chawdhry <m-chawdhry@ti.com>
To: Tom Rini <trini@konsulko.com>, "Andrew F. Davis" <afd@ti.com>,
Vignesh Raghavendra <vigneshr@ti.com>,
Kamlesh Gurudasani <kamlesh@ti.com>
Cc: <u-boot@lists.denx.de>, Praneeth Bajjuri <praneeth@ti.com>,
Neha Malcom Francis <n-francis@ti.com>,
Manorit Chawdhry <m-chawdhry@ti.com>
Subject: [PATCH v2 3/3] configs: j7200: Merge the HS and non-HS defconfigs
Date: Thu, 4 May 2023 11:07:08 +0530 [thread overview]
Message-ID: <20230405-j721s2-hs-evm-upstream-v2-3-c0f10a410e07@ti.com> (raw)
In-Reply-To: <20230405-j721s2-hs-evm-upstream-v2-0-c0f10a410e07@ti.com>
K3 devices have runtime type board detection. Make the default defconfig
include the secure configuration. Then remove the HS specific config.
Non-HS devices will continue to boot due to runtime device type detection.
If TI_SECURE_DEV_PKG is not set the build will emit warnings, for non-HS
devices these can be ignored.
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
MAINTAINERS | 2 -
configs/j7200_evm_a72_defconfig | 3 +-
configs/j7200_evm_r5_defconfig | 1 +
configs/j7200_hs_evm_a72_defconfig | 205 -------------------------------------
configs/j7200_hs_evm_r5_defconfig | 170 ------------------------------
5 files changed, 3 insertions(+), 378 deletions(-)
diff --git a/MAINTAINERS b/MAINTAINERS
index cb3d927a335b..9d203d5f42d6 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1494,8 +1494,6 @@ F: configs/k2g_hs_evm_defconfig
F: configs/k2l_hs_evm_defconfig
F: configs/am65x_hs_evm_r5_defconfig
F: configs/am65x_hs_evm_a53_defconfig
-F: configs/j7200_hs_evm_a72_defconfig
-F: configs/j7200_hs_evm_r5_defconfig
TPM DRIVERS
M: Ilias Apalodimas <ilias.apalodimas@linaro.org>
diff --git a/configs/j7200_evm_a72_defconfig b/configs/j7200_evm_a72_defconfig
index 058e33149684..e40900fffa49 100644
--- a/configs/j7200_evm_a72_defconfig
+++ b/configs/j7200_evm_a72_defconfig
@@ -1,5 +1,6 @@
CONFIG_ARM=y
CONFIG_ARCH_K3=y
+CONFIG_TI_SECURE_DEVICE=y
CONFIG_SYS_MALLOC_LEN=0x2000000
CONFIG_SYS_MALLOC_F_LEN=0x8000
CONFIG_SPL_GPIO=y
@@ -34,7 +35,7 @@ CONFIG_SPL_LOAD_FIT_ADDRESS=0x81000000
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_SYSTEM_SETUP=y
CONFIG_DISTRO_DEFAULTS=y
-CONFIG_BOOTCOMMAND="run findfdt; run envboot; run init_${boot}; run main_cpsw0_qsgmii_phyinit; run boot_rprocs; run get_kern_${boot}; run get_fdt_${boot}; run get_overlay_${boot}; run run_kern"
+CONFIG_BOOTCOMMAND="run findfdt; run envboot; run init_${boot}; run main_cpsw0_qsgmii_phyinit; run boot_rprocs; if test ${boot_fit} -eq 1; then run get_fit_${boot}; run get_overlaystring; run run_fit; else; run get_kern_${boot}; run get_fdt_${boot}; run get_overlay_${boot}; run run_kern; fi;"
CONFIG_LOGLEVEL=7
CONFIG_SPL_MAX_SIZE=0xc0000
CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
diff --git a/configs/j7200_evm_r5_defconfig b/configs/j7200_evm_r5_defconfig
index 00ec48b83b78..dd4454943c36 100644
--- a/configs/j7200_evm_r5_defconfig
+++ b/configs/j7200_evm_r5_defconfig
@@ -1,5 +1,6 @@
CONFIG_ARM=y
CONFIG_ARCH_K3=y
+CONFIG_TI_SECURE_DEVICE=y
CONFIG_SYS_MALLOC_LEN=0x2000000
CONFIG_SYS_MALLOC_F_LEN=0x70000
CONFIG_SPL_GPIO=y
diff --git a/configs/j7200_hs_evm_a72_defconfig b/configs/j7200_hs_evm_a72_defconfig
deleted file mode 100644
index d9560727edb3..000000000000
--- a/configs/j7200_hs_evm_a72_defconfig
+++ /dev/null
@@ -1,205 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_K3=y
-CONFIG_TI_SECURE_DEVICE=y
-CONFIG_SYS_MALLOC_LEN=0x2000000
-CONFIG_SYS_MALLOC_F_LEN=0x8000
-CONFIG_SPL_GPIO=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_SOC_K3_J721E=y
-CONFIG_TARGET_J7200_A72_EVM=y
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80480000
-CONFIG_ENV_SIZE=0x20000
-CONFIG_ENV_OFFSET=0x680000
-CONFIG_DM_GPIO=y
-CONFIG_SPL_DM_SPI=y
-CONFIG_DEFAULT_DEVICE_TREE="k3-j7200-common-proc-board"
-CONFIG_SPL_TEXT_BASE=0x80080000
-CONFIG_OF_LIBFDT_OVERLAY=y
-CONFIG_DM_RESET=y
-CONFIG_SPL_MMC=y
-CONFIG_SPL_SERIAL=y
-CONFIG_SPL_DRIVERS_MISC=y
-CONFIG_SPL_STACK_R_ADDR=0x82000000
-CONFIG_ENV_OFFSET_REDUND=0x6A0000
-CONFIG_SPL_FS_FAT=y
-CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_SPL_SPI=y
-# CONFIG_PSCI_RESET is not set
-# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
-CONFIG_SPL_LOAD_FIT=y
-CONFIG_SPL_LOAD_FIT_ADDRESS=0x81000000
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_SYSTEM_SETUP=y
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_BOOTCOMMAND="run findfdt; run envboot; run init_${boot}; run boot_rprocs; run get_fit_${boot}; run get_overlaystring; run run_fit"
-CONFIG_LOGLEVEL=7
-CONFIG_SPL_MAX_SIZE=0xc0000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x80a00000
-CONFIG_SPL_BSS_MAX_SIZE=0x80000
-CONFIG_SPL_BOARD_INIT=y
-CONFIG_SPL_SYS_MALLOC_SIMPLE=y
-CONFIG_SPL_STACK_R=y
-CONFIG_SYS_SPL_MALLOC=y
-CONFIG_SYS_SPL_MALLOC_SIZE=0x800000
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x1400
-CONFIG_SPL_DMA=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot.img"
-CONFIG_SPL_I2C=y
-CONFIG_SPL_DM_MAILBOX=y
-CONFIG_SPL_MTD_SUPPORT=y
-CONFIG_SPL_DM_SPI_FLASH=y
-CONFIG_SPL_NOR_SUPPORT=y
-CONFIG_SPL_DM_RESET=y
-CONFIG_SPL_POWER_DOMAIN=y
-CONFIG_SPL_RAM_SUPPORT=y
-CONFIG_SPL_RAM_DEVICE=y
-# CONFIG_SPL_SPI_FLASH_TINY is not set
-CONFIG_SPL_SPI_FLASH_SFDP_SUPPORT=y
-CONFIG_SPL_SPI_LOAD=y
-CONFIG_SYS_SPI_U_BOOT_OFFS=0x280000
-CONFIG_SPL_USB_GADGET=y
-CONFIG_SPL_DFU=y
-CONFIG_SPL_YMODEM_SUPPORT=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_DFU=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_MTD=y
-CONFIG_CMD_REMOTEPROC=y
-CONFIG_CMD_UFS=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_USB_MASS_STORAGE=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_TIME=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_MTDIDS_DEFAULT="nor0=47040000.spi.0,nor0=47034000.hyperbus"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=47040000.spi.0:512k(ospi.tiboot3),2m(ospi.tispl),4m(ospi.u-boot),128k(ospi.env),128k(ospi.env.backup),1m(ospi.sysfw),-@8m(ospi.rootfs);47034000.hyperbus:512k(hbmc.tiboot3),2m(hbmc.tispl),4m(hbmc.u-boot),256k(hbmc.env),1m(hbmc.sysfw),-@8m(hbmc.rootfs)"
-CONFIG_CMD_UBI=y
-# CONFIG_ISO_PARTITION is not set
-# CONFIG_SPL_EFI_PARTITION is not set
-CONFIG_OF_CONTROL=y
-CONFIG_SPL_OF_CONTROL=y
-CONFIG_SPL_MULTI_DTB_FIT=y
-CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_SPL_DM=y
-CONFIG_SPL_DM_SEQ_ALIAS=y
-CONFIG_REGMAP=y
-CONFIG_SPL_REGMAP=y
-CONFIG_SYSCON=y
-CONFIG_SPL_SYSCON=y
-CONFIG_SPL_OF_TRANSLATE=y
-CONFIG_CLK=y
-CONFIG_SPL_CLK=y
-CONFIG_CLK_CCF=y
-CONFIG_CLK_TI_SCI=y
-CONFIG_DFU_MMC=y
-CONFIG_DFU_RAM=y
-CONFIG_DFU_SF=y
-CONFIG_SYS_DFU_DATA_BUF_SIZE=0x40000
-CONFIG_SYS_DFU_MAX_FILE_SIZE=0x800000
-CONFIG_DMA_CHANNELS=y
-CONFIG_TI_K3_NAVSS_UDMA=y
-CONFIG_USB_FUNCTION_FASTBOOT=y
-CONFIG_FASTBOOT_BUF_ADDR=0x82000000
-CONFIG_FASTBOOT_BUF_SIZE=0x2F000000
-CONFIG_FASTBOOT_FLASH=y
-CONFIG_FASTBOOT_FLASH_MMC_DEV=0
-CONFIG_FASTBOOT_CMD_OEM_FORMAT=y
-CONFIG_TI_SCI_PROTOCOL=y
-CONFIG_DA8XX_GPIO=y
-CONFIG_DM_PCA953X=y
-CONFIG_DM_I2C=y
-CONFIG_DM_I2C_GPIO=y
-CONFIG_SYS_I2C_OMAP24XX=y
-CONFIG_DM_MAILBOX=y
-CONFIG_K3_SEC_PROXY=y
-CONFIG_SUPPORT_EMMC_BOOT=y
-CONFIG_MMC_IO_VOLTAGE=y
-CONFIG_MMC_UHS_SUPPORT=y
-CONFIG_MMC_HS400_SUPPORT=y
-CONFIG_SPL_MMC_HS400_SUPPORT=y
-CONFIG_MMC_SDHCI=y
-CONFIG_MMC_SDHCI_ADMA=y
-CONFIG_SPL_MMC_SDHCI_ADMA=y
-CONFIG_MMC_SDHCI_AM654=y
-CONFIG_MTD=y
-CONFIG_DM_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_SHOW_PROGRESS=0
-CONFIG_CFI_FLASH=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_HBMC_AM654=y
-CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
-CONFIG_DM_SPI_FLASH=y
-CONFIG_SPI_FLASH_STMICRO=y
-# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
-CONFIG_SPI_FLASH_MTD=y
-CONFIG_MULTIPLEXER=y
-CONFIG_MUX_MMIO=y
-CONFIG_PHY_FIXED=y
-CONFIG_TI_AM65_CPSW_NUSS=y
-CONFIG_PHY=y
-CONFIG_SPL_PHY=y
-CONFIG_PHY_CADENCE_TORRENT=y
-CONFIG_PHY_J721E_WIZ=y
-CONFIG_PINCTRL=y
-# CONFIG_PINCTRL_GENERIC is not set
-CONFIG_SPL_PINCTRL=y
-# CONFIG_SPL_PINCTRL_GENERIC is not set
-CONFIG_PINCTRL_SINGLE=y
-CONFIG_POWER_DOMAIN=y
-CONFIG_TI_SCI_POWER_DOMAIN=y
-CONFIG_DM_REGULATOR=y
-CONFIG_DM_REGULATOR_FIXED=y
-CONFIG_DM_REGULATOR_GPIO=y
-CONFIG_RAM=y
-CONFIG_SPL_RAM=y
-CONFIG_REMOTEPROC_TI_K3_R5F=y
-CONFIG_RESET_TI_SCI=y
-CONFIG_SCSI=y
-CONFIG_DM_SCSI=y
-CONFIG_DM_SERIAL=y
-CONFIG_SOC_DEVICE=y
-CONFIG_SOC_DEVICE_TI_K3=y
-CONFIG_SOC_TI=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_CADENCE_QSPI=y
-CONFIG_HAS_CQSPI_REF_CLK=y
-CONFIG_CQSPI_REF_CLK=133333333
-CONFIG_SYSRESET=y
-CONFIG_SPL_SYSRESET=y
-CONFIG_SYSRESET_TI_SCI=y
-CONFIG_USB=y
-CONFIG_DM_USB_GADGET=y
-CONFIG_SPL_DM_USB_GADGET=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_CDNS3=y
-CONFIG_USB_CDNS3_GADGET=y
-CONFIG_USB_CDNS3_HOST=y
-CONFIG_SPL_USB_CDNS3_GADGET=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments"
-CONFIG_USB_GADGET_VENDOR_NUM=0x0451
-CONFIG_USB_GADGET_PRODUCT_NUM=0x6164
-CONFIG_UFS=y
-CONFIG_CADENCE_UFS=y
-CONFIG_TI_J721E_UFS=y
diff --git a/configs/j7200_hs_evm_r5_defconfig b/configs/j7200_hs_evm_r5_defconfig
deleted file mode 100644
index 94a6523f06c2..000000000000
--- a/configs/j7200_hs_evm_r5_defconfig
+++ /dev/null
@@ -1,170 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_K3=y
-CONFIG_TI_SECURE_DEVICE=y
-CONFIG_SYS_MALLOC_LEN=0x2000000
-CONFIG_SYS_MALLOC_F_LEN=0x70000
-CONFIG_SPL_GPIO=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_SOC_K3_J721E=y
-CONFIG_K3_EARLY_CONS=y
-CONFIG_TARGET_J7200_R5_EVM=y
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x41cf5bfc
-CONFIG_ENV_SIZE=0x20000
-CONFIG_DM_GPIO=y
-CONFIG_SPL_DM_SPI=y
-CONFIG_DEFAULT_DEVICE_TREE="k3-j7200-r5-common-proc-board"
-CONFIG_SPL_TEXT_BASE=0x41c00000
-CONFIG_DM_RESET=y
-CONFIG_SPL_MMC=y
-CONFIG_SPL_SERIAL=y
-CONFIG_SPL_DRIVERS_MISC=y
-CONFIG_SPL_STACK_R_ADDR=0x82000000
-CONFIG_SPL_FS_FAT=y
-CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_SPL_SPI=y
-# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
-CONFIG_SPL_LOAD_FIT=y
-CONFIG_SPL_LOAD_FIT_ADDRESS=0x80080000
-CONFIG_USE_BOOTCOMMAND=y
-# CONFIG_DISPLAY_CPUINFO is not set
-CONFIG_SPL_MAX_SIZE=0xc0000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x41cf5bfc
-CONFIG_SPL_BSS_MAX_SIZE=0xa000
-CONFIG_SPL_BOARD_INIT=y
-CONFIG_SPL_STACK_R=y
-CONFIG_SPL_SEPARATE_BSS=y
-CONFIG_SYS_SPL_MALLOC=y
-CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y
-CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x84000000
-CONFIG_SYS_SPL_MALLOC_SIZE=0x1000000
-CONFIG_SPL_EARLY_BSS=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x400
-CONFIG_SPL_DMA=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_FS_EXT4=y
-CONFIG_SPL_I2C=y
-CONFIG_SPL_DM_MAILBOX=y
-CONFIG_SPL_MTD_SUPPORT=y
-CONFIG_SPL_DM_SPI_FLASH=y
-CONFIG_SPL_NOR_SUPPORT=y
-CONFIG_SPL_DM_RESET=y
-CONFIG_SPL_POWER_DOMAIN=y
-CONFIG_SPL_RAM_SUPPORT=y
-CONFIG_SPL_RAM_DEVICE=y
-CONFIG_SPL_REMOTEPROC=y
-# CONFIG_SPL_SPI_FLASH_TINY is not set
-CONFIG_SPL_SPI_FLASH_SFDP_SUPPORT=y
-CONFIG_SPL_SPI_LOAD=y
-CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000
-CONFIG_SPL_USB_GADGET=y
-CONFIG_SPL_DFU=y
-CONFIG_SPL_YMODEM_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_BOOTM_LEN=0x4000000
-CONFIG_CMD_DFU=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPT=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_REMOTEPROC=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_TIME=y
-CONFIG_CMD_FAT=y
-CONFIG_OF_CONTROL=y
-CONFIG_SPL_OF_CONTROL=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SPL_DM=y
-CONFIG_SPL_DM_SEQ_ALIAS=y
-CONFIG_REGMAP=y
-CONFIG_SPL_REGMAP=y
-CONFIG_SYSCON=y
-CONFIG_SPL_SYSCON=y
-CONFIG_SPL_OF_TRANSLATE=y
-CONFIG_CLK=y
-CONFIG_SPL_CLK=y
-CONFIG_SPL_CLK_CCF=y
-CONFIG_SPL_CLK_K3_PLL=y
-CONFIG_SPL_CLK_K3=y
-CONFIG_SYS_DFU_DATA_BUF_SIZE=0x40000
-CONFIG_DMA_CHANNELS=y
-CONFIG_TI_K3_NAVSS_UDMA=y
-CONFIG_TI_SCI_PROTOCOL=y
-CONFIG_DA8XX_GPIO=y
-CONFIG_DM_PCA953X=y
-CONFIG_DM_I2C=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_I2C_OMAP24XX=y
-CONFIG_DM_MAILBOX=y
-CONFIG_K3_SEC_PROXY=y
-CONFIG_FS_LOADER=y
-CONFIG_SPL_FS_LOADER=y
-CONFIG_K3_AVS0=y
-CONFIG_SUPPORT_EMMC_BOOT=y
-CONFIG_SPL_MMC_HS400_SUPPORT=y
-CONFIG_MMC_SDHCI=y
-CONFIG_SPL_MMC_SDHCI_ADMA=y
-CONFIG_MMC_SDHCI_AM654=y
-CONFIG_MTD=y
-CONFIG_DM_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_SHOW_PROGRESS=0
-CONFIG_CFI_FLASH=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_HBMC_AM654=y
-CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
-CONFIG_DM_SPI_FLASH=y
-CONFIG_SPI_FLASH_SFDP_SUPPORT=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PINCTRL=y
-# CONFIG_PINCTRL_GENERIC is not set
-CONFIG_SPL_PINCTRL=y
-# CONFIG_SPL_PINCTRL_GENERIC is not set
-CONFIG_PINCTRL_SINGLE=y
-CONFIG_POWER_DOMAIN=y
-CONFIG_TI_SCI_POWER_DOMAIN=y
-CONFIG_TI_POWER_DOMAIN=y
-CONFIG_DM_PMIC=y
-CONFIG_PMIC_TPS65941=y
-CONFIG_DM_REGULATOR=y
-CONFIG_SPL_DM_REGULATOR=y
-CONFIG_DM_REGULATOR_TPS65941=y
-CONFIG_K3_SYSTEM_CONTROLLER=y
-CONFIG_REMOTEPROC_TI_K3_ARM64=y
-CONFIG_RESET_TI_SCI=y
-CONFIG_DM_SERIAL=y
-CONFIG_SOC_DEVICE=y
-CONFIG_SOC_DEVICE_TI_K3=y
-CONFIG_SOC_TI=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_CADENCE_QSPI=y
-CONFIG_HAS_CQSPI_REF_CLK=y
-CONFIG_CQSPI_REF_CLK=133333333
-CONFIG_SYSRESET=y
-CONFIG_SPL_SYSRESET=y
-CONFIG_SYSRESET_TI_SCI=y
-CONFIG_TIMER=y
-CONFIG_SPL_TIMER=y
-CONFIG_OMAP_TIMER=y
-CONFIG_USB=y
-CONFIG_DM_USB_GADGET=y
-CONFIG_SPL_DM_USB_GADGET=y
-CONFIG_USB_CDNS3=y
-CONFIG_USB_CDNS3_GADGET=y
-CONFIG_SPL_USB_CDNS3_GADGET=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments"
-CONFIG_USB_GADGET_VENDOR_NUM=0x0451
-CONFIG_USB_GADGET_PRODUCT_NUM=0x6164
-CONFIG_USB_GADGET_DOWNLOAD=y
-CONFIG_FS_EXT4=y
-CONFIG_FS_FAT_MAX_CLUSTSIZE=16384
-CONFIG_LIB_RATIONAL=y
-CONFIG_SPL_LIB_RATIONAL=y
--
2.34.1
next prev parent reply other threads:[~2023-05-04 5:38 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-05-04 5:37 [PATCH v2 0/3] J7 merge HS configs Manorit Chawdhry
2023-05-04 5:37 ` [PATCH v2 1/3] configs: j721s2: Merge the HS and non-HS defconfigs Manorit Chawdhry
2023-05-05 0:59 ` Tom Rini
2023-05-04 5:37 ` [PATCH v2 2/3] Kconfig: j721s2: Change K3_MCU_SCRATCHPAD_BASE to non firewalled region Manorit Chawdhry
2023-05-05 0:59 ` Tom Rini
2023-05-05 13:45 ` Nishanth Menon
2023-05-08 4:51 ` Manorit Chawdhry
2023-05-08 4:57 ` Vignesh Raghavendra
2023-05-08 5:07 ` Manorit Chawdhry
2023-05-04 5:37 ` Manorit Chawdhry [this message]
2023-05-05 0:59 ` [PATCH v2 3/3] configs: j7200: Merge the HS and non-HS defconfigs Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230405-j721s2-hs-evm-upstream-v2-3-c0f10a410e07@ti.com \
--to=m-chawdhry@ti.com \
--cc=afd@ti.com \
--cc=kamlesh@ti.com \
--cc=n-francis@ti.com \
--cc=praneeth@ti.com \
--cc=trini@konsulko.com \
--cc=u-boot@lists.denx.de \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.