[PATCH v2 7/8] arm64: dts: qcom: sm8650-mtp: add interconnect dependent device nodes

From: Neil Armstrong <neil.armstrong@linaro.org>
To: Andy Gross <agross@kernel.org>,
	Bjorn Andersson <andersson@kernel.org>,
	Konrad Dybcio <konrad.dybcio@linaro.org>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Conor Dooley <conor+dt@kernel.org>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org,
	Neil Armstrong <neil.armstrong@linaro.org>
Subject: [PATCH v2 7/8] arm64: dts: qcom: sm8650-mtp: add interconnect dependent device nodes
Date: Mon, 06 Nov 2023 09:39:15 +0100	[thread overview]
Message-ID: <20231106-topic-sm8650-upstream-dt-v2-7-44d6f9710fa7@linaro.org> (raw)
In-Reply-To: <20231106-topic-sm8650-upstream-dt-v2-0-44d6f9710fa7@linaro.org>

Now interconnect dependent devices are added in sm8650 DTSI,
now enable more devices for the Qualcomm SM8650 MTP board:
- PCIe
- Display
- DSPs
- SDCard
- UFS
- USB role switch with PMIC Glink

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8650-mtp.dts | 235 +++++++++++++++++++++++++++++++-
 1 file changed, 234 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8650-mtp.dts b/arch/arm64/boot/dts/qcom/sm8650-mtp.dts
index 5738791fea2a..73c781089425 100644
--- a/arch/arm64/boot/dts/qcom/sm8650-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8650-mtp.dts
@@ -28,6 +28,44 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	pmic-glink {
+		compatible = "qcom,sm8650-pmic-glink",
+			     "qcom,sm8550-pmic-glink",
+			     "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		orientation-gpios = <&tlmm 29 GPIO_ACTIVE_HIGH>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_hs_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_ss>;
+					};
+				};
+			};
+		};
+	};
+
 	vph_pwr: vph-pwr-regulator {
 		compatible = "regulator-fixed";
 
@@ -77,6 +115,9 @@ vreg_l2b_3p0: ldo2 {
 			regulator-min-microvolt = <3008000>;
 			regulator-max-microvolt = <3008000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l5b_3p1: ldo5 {
@@ -389,6 +430,106 @@ vreg_l3i_1p2: ldo3 {
 	};
 };
 
+&dispcc {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l3i_1p2>;
+
+	status = "okay";
+
+	panel@0 {
+		compatible = "visionox,vtdr6130";
+		reg = <0>;
+
+		reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+
+		vddio-supply = <&vreg_l12b_1p8>;
+		vci-supply = <&vreg_l13b_3p0>;
+		vdd-supply = <&vreg_l11b_1p2>;
+
+		pinctrl-0 = <&sde_dsi_active>, <&sde_te_active>;
+		pinctrl-1 = <&sde_dsi_suspend>, <&sde_te_suspend>;
+		pinctrl-names = "default", "sleep";
+
+		port {
+			panel0_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel0_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	vdds-supply = <&vreg_l1i_0p88>;
+
+	status = "okay";
+};
+
+&mdss_mdp {
+	status = "okay";
+};
+
+&pcie_1_phy_aux_clk {
+	clock-frequency = <1000>;
+};
+
+&pcie0 {
+	wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie0_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&vreg_l1i_0p88>;
+	vdda-pll-supply = <&vreg_l3i_1p2>;
+
+	status = "okay";
+};
+
+&pcie1 {
+	wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie1_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie1_phy {
+	vdda-phy-supply = <&vreg_l3e_0p9>;
+	vdda-pll-supply = <&vreg_l3i_1p2>;
+	vdda-qref-supply = <&vreg_l1i_0p88>;
+
+	status = "okay";
+};
+
+&pm8550_gpios {
+	sdc2_card_det_n: sdc2-card-det-state {
+		pins = "gpio12";
+		function = "normal";
+		bias-pull-up;
+		input-enable;
+		output-disable;
+		power-source = <1>; /* 1.8 V */
+	};
+};
+
 &pm8550b_eusb2_repeater {
 	vdd18-supply = <&vreg_l15b_1p8>;
 	vdd3-supply = <&vreg_l5b_3p1>;
@@ -398,18 +539,101 @@ &qupv3_id_1 {
 	status = "okay";
 };
 
+&remoteproc_adsp {
+	firmware-name = "qcom/sm8650/adsp.mbn",
+			"qcom/sm8650/adsp_dtb.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/sm8650/cdsp.mbn",
+			"qcom/sm8650/cdsp_dtb.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_mpss {
+	firmware-name = "qcom/sm8650/modem.mbn",
+			"qcom/sm8650/modem_dtb.mbn";
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
+
+	vmmc-supply = <&vreg_l9b_2p9>;
+	vqmmc-supply = <&vreg_l8b_1p8>;
+	bus-width = <4>;
+	no-sdio;
+	no-mmc;
+
+	pinctrl-0 = <&sdc2_default>, <&sdc2_card_det_n>;
+	pinctrl-1 = <&sdc2_sleep>, <&sdc2_card_det_n>;
+	pinctrl-names = "default", "sleep";
+
+	status = "okay";
+};
+
 &sleep_clk {
 	clock-frequency = <32000>;
 };
 
 &tlmm {
 	gpio-reserved-ranges = <32 8>;
+
+	sde_dsi_active: sde-dsi-active-state {
+		pins = "gpio133";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	sde_dsi_suspend: sde-dsi-suspend-state {
+		pins = "gpio133";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	sde_te_active: sde-te-active-state {
+		pins = "gpio86";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	sde_te_suspend: sde-te-suspend-state {
+		pins = "gpio86";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
 };
 
 &uart15 {
 	status = "okay";
 };
 
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l17b_2p5>;
+	vcc-max-microamp = <1300000>;
+	vccq-supply = <&vreg_l1c_1p2>;
+	vccq-max-microamp = <1200000>;
+
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l1d_0p88>;
+	vdda-pll-supply = <&vreg_l3i_1p2>;
+
+	status = "okay";
+};
+
 /*
  * DPAUX -> WCD9395 -> USB_SBU -> USB-C
  * eUSB2 DP/DM -> PM85550HS -> eUSB2 DP/DM -> USB-C
@@ -421,7 +645,16 @@ &usb_1 {
 };
 
 &usb_1_dwc3 {
-	dr_mode = "peripheral";
+	dr_mode = "otg";
+	usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+	remote-endpoint = <&pmic_glink_ss_in>;
 };
 
 &usb_1_hsphy {

-- 
2.34.1

