From: Abel Vesa <abel.vesa@linaro.org>
To: Andy Gross <agross@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konrad.dybcio@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>,
Sibi Sankar <quic_sibis@quicinc.com>,
Rajendra Nayak <quic_rjendra@quicinc.com>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, Abel Vesa <abel.vesa@linaro.org>
Subject: [PATCH v6 08/11] arm64: dts: qcom: x1e80100: Add display nodes
Date: Mon, 29 Jan 2024 14:45:40 +0200 [thread overview]
Message-ID: <20240129-x1e80100-dts-missing-nodes-v6-8-2c0e691cfa3b@linaro.org> (raw)
In-Reply-To: <20240129-x1e80100-dts-missing-nodes-v6-0-2c0e691cfa3b@linaro.org>
Add the required nodes to support display on X1E80100.
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
arch/arm64/boot/dts/qcom/x1e80100.dtsi | 519 +++++++++++++++++++++++++++++++++
1 file changed, 519 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index 20aa04aa80f7..7fc5883bf593 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -4,6 +4,7 @@
*/
#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/clock/qcom,x1e80100-dispcc.h>
#include <dt-bindings/clock/qcom,x1e80100-gcc.h>
#include <dt-bindings/clock/qcom,x1e80100-tcsr.h>
#include <dt-bindings/dma/qcom-gpi.h>
@@ -3344,6 +3345,524 @@ usb_1_ss1_role_switch: endpoint {
};
};
+ mdss: display-subsystem@ae00000 {
+ compatible = "qcom,x1e80100-mdss";
+ reg = <0 0x0ae00000 0 0x1000>;
+ reg-names = "mdss";
+
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>;
+
+ resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
+
+ interconnects = <&mmss_noc MASTER_MDP QCOM_ICC_TAG_ALWAYS
+ &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+ <&mc_virt MASTER_LLCC QCOM_ICC_TAG_ALWAYS
+ &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+ <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY
+ &config_noc SLAVE_DISPLAY_CFG QCOM_ICC_TAG_ACTIVE_ONLY>;
+ interconnect-names = "mdp0-mem",
+ "mdp1-mem",
+ "cpu-cfg";
+
+ power-domains = <&dispcc MDSS_GDSC>;
+
+ iommus = <&apps_smmu 0x1c00 0x2>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ status = "disabled";
+
+ mdss_mdp: display-controller@ae01000 {
+ compatible = "qcom,x1e80100-dpu";
+ reg = <0 0x0ae01000 0 0x8f000>,
+ <0 0x0aeb0000 0 0x2008>;
+ reg-names = "mdp",
+ "vbif";
+
+ interrupts-extended = <&mdss 0>;
+
+ clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "nrt_bus",
+ "iface",
+ "lut",
+ "core",
+ "vsync";
+
+ operating-points-v2 = <&mdp_opp_table>;
+
+ power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ mdss_intf0_out: endpoint {
+ remote-endpoint = <&mdss_dp0_in>;
+ };
+ };
+
+ port@4 {
+ reg = <4>;
+
+ mdss_intf4_out: endpoint {
+ remote-endpoint = <&mdss_dp1_in>;
+ };
+ };
+
+ port@5 {
+ reg = <5>;
+
+ mdss_intf5_out: endpoint {
+ remote-endpoint = <&mdss_dp3_in>;
+ };
+ };
+
+ port@6 {
+ reg = <6>;
+
+ mdss_intf6_out: endpoint {
+ remote-endpoint = <&mdss_dp2_in>;
+ };
+ };
+ };
+
+ mdp_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-200000000 {
+ opp-hz = /bits/ 64 <200000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-325000000 {
+ opp-hz = /bits/ 64 <325000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-514000000 {
+ opp-hz = /bits/ 64 <514000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+
+ opp-575000000 {
+ opp-hz = /bits/ 64 <575000000>;
+ required-opps = <&rpmhpd_opp_nom_l1>;
+ };
+ };
+ };
+
+ mdss_dp0: displayport-controller@ae90000 {
+ compatible = "qcom,x1e80100-dp";
+ reg = <0 0xae90000 0 0x200>,
+ <0 0xae90200 0 0x200>,
+ <0 0xae90400 0 0x600>,
+ <0 0xae91000 0 0x400>,
+ <0 0xae91400 0 0x400>;
+
+ interrupts-extended = <&mdss 12>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX0_AUX_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX0_LINK_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX0_LINK_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX0_PIXEL0_CLK>;
+ clock-names = "core_iface",
+ "core_aux",
+ "ctrl_link",
+ "ctrl_link_iface",
+ "stream_pixel";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX0_LINK_CLK_SRC>,
+ <&dispcc DISP_CC_MDSS_DPTX0_PIXEL0_CLK_SRC>;
+ assigned-clock-parents = <&usb_1_ss0_qmpphy QMP_USB43DP_DP_LINK_CLK>,
+ <&usb_1_ss0_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;
+
+ operating-points-v2 = <&mdss_dp0_opp_table>;
+
+ power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+ phys = <&usb_1_ss0_qmpphy QMP_USB43DP_DP_PHY>;
+ phy-names = "dp";
+
+ #sound-dai-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ mdss_dp0_in: endpoint {
+ remote-endpoint = <&mdss_intf0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ mdss_dp0_out: endpoint {
+ };
+ };
+ };
+
+ mdss_dp0_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-270000000 {
+ opp-hz = /bits/ 64 <270000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-540000000 {
+ opp-hz = /bits/ 64 <540000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-810000000 {
+ opp-hz = /bits/ 64 <810000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
+ mdss_dp1: displayport-controller@ae98000 {
+ compatible = "qcom,x1e80100-dp";
+ reg = <0 0xae98000 0 0x200>,
+ <0 0xae98200 0 0x200>,
+ <0 0xae98400 0 0x600>,
+ <0 0xae99000 0 0x400>,
+ <0 0xae99400 0 0x400>;
+
+ interrupts-extended = <&mdss 13>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX1_AUX_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX1_LINK_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX1_LINK_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX1_PIXEL0_CLK>;
+ clock-names = "core_iface",
+ "core_aux",
+ "ctrl_link",
+ "ctrl_link_iface",
+ "stream_pixel";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX1_LINK_CLK_SRC>,
+ <&dispcc DISP_CC_MDSS_DPTX1_PIXEL0_CLK_SRC>;
+ assigned-clock-parents = <&usb_1_ss1_qmpphy QMP_USB43DP_DP_LINK_CLK>,
+ <&usb_1_ss1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;
+
+ operating-points-v2 = <&mdss_dp1_opp_table>;
+
+ power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+ phys = <&usb_1_ss1_qmpphy QMP_USB43DP_DP_PHY>;
+ phy-names = "dp";
+
+ #sound-dai-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ mdss_dp1_in: endpoint {
+ remote-endpoint = <&mdss_intf4_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ mdss_dp1_out: endpoint {
+ };
+ };
+ };
+
+ mdss_dp1_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-270000000 {
+ opp-hz = /bits/ 64 <270000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-540000000 {
+ opp-hz = /bits/ 64 <540000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-810000000 {
+ opp-hz = /bits/ 64 <810000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
+ mdss_dp2: displayport-controller@ae9a000 {
+ compatible = "qcom,x1e80100-dp";
+ reg = <0 0xae9a000 0 0x200>,
+ <0 0xae9a200 0 0x200>,
+ <0 0xae9a400 0 0x600>,
+ <0 0xae9b000 0 0x400>,
+ <0 0xae9b400 0 0x400>;
+
+ interrupts-extended = <&mdss 14>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX2_AUX_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX2_LINK_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX2_LINK_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX2_PIXEL0_CLK>;
+ clock-names = "core_iface",
+ "core_aux",
+ "ctrl_link",
+ "ctrl_link_iface",
+ "stream_pixel";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX2_LINK_CLK_SRC>,
+ <&dispcc DISP_CC_MDSS_DPTX2_PIXEL0_CLK_SRC>;
+ assigned-clock-parents = <&mdss_dp2_phy 0>,
+ <&mdss_dp2_phy 1>;
+
+ operating-points-v2 = <&mdss_dp2_opp_table>;
+
+ power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+ phys = <&mdss_dp2_phy>;
+ phy-names = "dp";
+
+ #sound-dai-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdss_dp2_in: endpoint {
+ remote-endpoint = <&mdss_intf6_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ };
+ };
+
+ mdss_dp2_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-270000000 {
+ opp-hz = /bits/ 64 <270000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-540000000 {
+ opp-hz = /bits/ 64 <540000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-810000000 {
+ opp-hz = /bits/ 64 <810000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
+ mdss_dp3: displayport-controller@aea0000 {
+ compatible = "qcom,x1e80100-dp";
+ reg = <0 0xaea0000 0 0x200>,
+ <0 0xaea0200 0 0x200>,
+ <0 0xaea0400 0 0x600>,
+ <0 0xaea1000 0 0x400>,
+ <0 0xaea1400 0 0x400>;
+
+ interrupts-extended = <&mdss 15>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX3_AUX_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX3_LINK_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX3_LINK_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX3_PIXEL0_CLK>;
+ clock-names = "core_iface",
+ "core_aux",
+ "ctrl_link",
+ "ctrl_link_iface",
+ "stream_pixel";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX3_LINK_CLK_SRC>,
+ <&dispcc DISP_CC_MDSS_DPTX3_PIXEL0_CLK_SRC>;
+ assigned-clock-parents = <&mdss_dp3_phy 0>,
+ <&mdss_dp3_phy 1>;
+
+ operating-points-v2 = <&mdss_dp3_opp_table>;
+
+ power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+ phys = <&mdss_dp3_phy>;
+ phy-names = "dp";
+
+ #sound-dai-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ mdss_dp3_in: endpoint {
+ remote-endpoint = <&mdss_intf5_out>;
+
+ link-frequencies = /bits/ 64 <8100000000>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ };
+ };
+
+ mdss_dp3_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-270000000 {
+ opp-hz = /bits/ 64 <270000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-540000000 {
+ opp-hz = /bits/ 64 <540000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-810000000 {
+ opp-hz = /bits/ 64 <810000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
+ };
+
+ mdss_dp2_phy: phy@aec2a00 {
+ compatible = "qcom,x1e80100-dp-phy";
+ reg = <0 0x0aec2a00 0 0x19c>,
+ <0 0x0aec2200 0 0xec>,
+ <0 0x0aec2600 0 0xec>,
+ <0 0x0aec2000 0 0x1c8>;
+
+ clocks = <&dispcc DISP_CC_MDSS_DPTX2_AUX_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>;
+ clock-names = "aux",
+ "cfg_ahb";
+
+ power-domains = <&rpmhpd RPMHPD_MX>;
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ mdss_dp3_phy: phy@aec5a00 {
+ compatible = "qcom,x1e80100-dp-phy";
+ reg = <0 0x0aec5a00 0 0x19c>,
+ <0 0x0aec5200 0 0xec>,
+ <0 0x0aec5600 0 0xec>,
+ <0 0x0aec5000 0 0x1c8>;
+
+ clocks = <&dispcc DISP_CC_MDSS_DPTX3_AUX_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>;
+ clock-names = "aux",
+ "cfg_ahb";
+
+ power-domains = <&rpmhpd RPMHPD_MX>;
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ dispcc: clock-controller@af00000 {
+ compatible = "qcom,x1e80100-dispcc";
+ reg = <0 0x0af00000 0 0x20000>;
+ clocks = <&bi_tcxo_div2>,
+ <&bi_tcxo_ao_div2>,
+ <&gcc GCC_DISP_AHB_CLK>,
+ <&sleep_clk>,
+ <0>, /* dsi0 */
+ <0>,
+ <0>, /* dsi1 */
+ <0>,
+ <&usb_1_ss0_qmpphy QMP_USB43DP_DP_LINK_CLK>, /* dp0 */
+ <&usb_1_ss0_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>,
+ <&usb_1_ss1_qmpphy QMP_USB43DP_DP_LINK_CLK>, /* dp1 */
+ <&usb_1_ss1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>,
+ <&mdss_dp2_phy 0>, /* dp2 */
+ <&mdss_dp2_phy 1>,
+ <&mdss_dp3_phy 0>, /* dp3 */
+ <&mdss_dp3_phy 1>;
+ power-domains = <&rpmhpd RPMHPD_MMCX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ };
+
pdc: interrupt-controller@b220000 {
compatible = "qcom,x1e80100-pdc", "qcom,pdc";
reg = <0 0x0b220000 0 0x30000>, <0 0x174000f0 0 0x64>;
--
2.34.1
next prev parent reply other threads:[~2024-01-29 12:46 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-01-29 12:45 [PATCH v6 00/11] arm64: dts: qcom: Add more support to X1E80100 base dtsi, CRD and QCP boards Abel Vesa
2024-01-29 12:45 ` [PATCH v6 01/11] arm64: dts: qcom: x1e80100: Add IPCC node Abel Vesa
2024-01-29 12:45 ` [PATCH v6 02/11] arm64: dts: qcom: x1e80100: Add SMP2P nodes Abel Vesa
2024-01-29 12:45 ` [PATCH v6 03/11] arm64: dts: qcom: x1e80100: Add QMP AOSS node Abel Vesa
2024-01-29 12:45 ` [PATCH v6 04/11] arm64: dts: qcom: x1e80100: Add ADSP/CDSP remoteproc nodes Abel Vesa
2024-01-29 12:45 ` [PATCH v6 05/11] arm64: dts: qcom: x1e80100: Add TCSR node Abel Vesa
2024-02-01 19:19 ` Konrad Dybcio
2024-01-29 12:45 ` [PATCH v6 06/11] arm64: dts: qcom: x1e80100: Add USB nodes Abel Vesa
2024-01-29 12:45 ` [PATCH v6 07/11] arm64: dts: qcom: x1e80100: Add PCIe nodes Abel Vesa
2024-01-29 12:45 ` Abel Vesa [this message]
2024-01-29 12:45 ` [PATCH v6 09/11] arm64: dts: qcom: x1e80100-crd: Enable more support Abel Vesa
2024-01-29 12:45 ` [PATCH v6 10/11] arm64: dts: qcom: x1e80100-qcp: " Abel Vesa
2024-01-29 12:45 ` [PATCH v6 11/11] arm64: dts: qcom: x1e80100-qcp: Fix supplies for LDOs 3E and 2J Abel Vesa
2024-02-07 4:46 ` [PATCH v6 00/11] arm64: dts: qcom: Add more support to X1E80100 base dtsi, CRD and QCP boards Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240129-x1e80100-dts-missing-nodes-v6-8-2c0e691cfa3b@linaro.org \
--to=abel.vesa@linaro.org \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=quic_rjendra@quicinc.com \
--cc=quic_sibis@quicinc.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.