Re: recording problem in beagleboard-mcbsp

From: Variksla <variksla@gmail.com>
To: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: "alsa-devel@alsa-project.org" <alsa-devel@alsa-project.org>,
	"broonie@kernel.org" <broonie@kernel.org>
Subject: Re: recording problem in beagleboard-mcbsp
Date: Tue, 14 Apr 2015 09:41:50 -0700	[thread overview]
Message-ID: <8EE6AA19-869C-4EFD-984E-7BCAADE91D1F@gmail.com> (raw)
In-Reply-To: <552D0A6A.20800@ti.com>


> On Apr 14, 2015, at 5:39 AM, Peter Ujfalusi <peter.ujfalusi@ti.com> wrote:
> 
>> On 04/14/2015 12:39 PM, Peter Ujfalusi wrote:
>> OK, got another SD card.
>> McBSP3 in master mode works (no codec connected) playback and capture as well.
>> 
>> The pins for McBSP3:
>> OMAP3_CORE1_IOPAD(0x2172, PIN_OUTPUT | MUX_MODE0) /* mcbsp3_fsx.mcbsp3_fsx */
>> OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE1) /* uart2_tx.mcbsp3_clkx */
>> OMAP3_CORE1_IOPAD(0x2174, PIN_OUTPUT | MUX_MODE1) /* uart2_cts.mcbsp3_dx */
>> OMAP3_CORE1_IOPAD(0x2176, PIN_INPUT | MUX_MODE1)  /* uart2_rts.mcbsp3_dr */
>> 
>> I still not sure why McBSP1 is not working..
> 
> This pinctrl setting is not correct for McBSP3. I was changing the registers
> on the fly, that's why it was working when I replied.
> 
> In McBSP3 master mode, you need:
> OMAP3_CORE1_IOPAD(0x2172, PIN_INPUT | MUX_MODE0) /* mcbsp3_fsx.mcbsp3_fsx */
> OMAP3_CORE1_IOPAD(0x2178, PIN_INPUT | MUX_MODE1) /* uart2_tx.mcbsp3_clkx */
> OMAP3_CORE1_IOPAD(0x2174, PIN_OUTPUT | MUX_MODE1) /* uart2_cts.mcbsp3_dx */
> OMAP3_CORE1_IOPAD(0x2176, PIN_INPUT | MUX_MODE1)  /* uart2_rts.mcbsp3_dr */

Weird. If mcbsp3 is master I am wondering why we are configuring fsx and clkx as input. 
> 
> Which would work in McBSP3 slave mode as well.
> Playback, capture works (McBSP3 master). I have connected DX to DR and
> captured whatever I was playing. Came back fine.
> 
> As for McBSP1 I think this should get it working:
> OMAP3_CORE1_IOPAD(0x2196, PIN_INPUT | MUX_MODE0) /* mcbsp1_fsx.mcbsp1_fsx */
> OMAP3_CORE1_IOPAD(0x218e, PIN_INPUT | MUX_MODE0) /* mcbsp1_fsr.mcbsp1_fsr */
> OMAP3_CORE1_IOPAD(0x2198, PIN_INPUT | MUX_MODE0) /* mcbsp1_clkx.mcbsp1_clkx */
> OMAP3_CORE1_IOPAD(0x218c, PIN_INPUT | MUX_MODE0) /* mcbsp1_clkr.mcbsp1_clkr */
> OMAP3_CORE1_IOPAD(0x2190, PIN_OUTPUT | MUX_MODE0) /* mcbsp1_dx.mcbsp1_dx */
> OMAP3_CORE1_IOPAD(0x2192, PIN_INPUT | MUX_MODE0)  /* mcbsp1_dr.mcbsp1_dr */
> 
> If McBSP1 is slave, then connect the FS to both FSX and FSR and do the same
> for CLK.
> 
> -- 
> Péter
_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel