From: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
To: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>,
Matti Vaittinen <mazziesaccount@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Liam Girdwood <lgirdwood@gmail.com>,
Mark Brown <broonie@kernel.org>,
Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-power@fi.rohmeurope.com
Subject: [PATCH v6 13/16] regulator: Support ROHM BD71815 regulators
Date: Mon, 5 Apr 2021 14:44:16 +0300 [thread overview]
Message-ID: <9964349abe1c3e5fe06f71019d86ba1a967d01a8.1617616855.git.matti.vaittinen@fi.rohmeurope.com> (raw)
In-Reply-To: <cover.1617616855.git.matti.vaittinen@fi.rohmeurope.com>
Support voltage control for regulators on ROHM BD71815 PMIC.
ROHM BD71815 contains 5 bucks, 7 LDOs and a boost (intended for LED).
Bucks 1 and 2 support HW state based voltage level and enable states. Other
regulators support HW state based enable states. All bucks and LDOs 1-5
allow voltage changes for RUN state and LDO4 can be enabled/disabled via
GPIO.
LDO3 does support changing between two predetermined voltages by using
a GPIO but this functionality is not included in this commit.
This work is derived from driver originally written by Tony Luo
<luofc@embedinfo.com> - although not much of original work is left.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
---
Changes since v4:
- unify whole comment block to use c++ comments as was suggested by Mark
- drop inclusion of machine.h
- squash in the patch which made BD71815 to use generic ramp-delay as
generic ramp-delay support was added to the regulator tree.
drivers/regulator/Kconfig | 11 +
drivers/regulator/Makefile | 1 +
drivers/regulator/bd71815-regulator.c | 652 ++++++++++++++++++++++++++
3 files changed, 664 insertions(+)
create mode 100644 drivers/regulator/bd71815-regulator.c
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 77c43134bc9e..6437348ce862 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -204,6 +204,17 @@ config REGULATOR_BD70528
This driver can also be built as a module. If so, the module
will be called bd70528-regulator.
+config REGULATOR_BD71815
+ tristate "ROHM BD71815 Power Regulator"
+ depends on MFD_ROHM_BD71828
+ help
+ This driver supports voltage regulators on ROHM BD71815 PMIC.
+ This will enable support for the software controllable buck
+ and LDO regulators and a current regulator for LEDs.
+
+ This driver can also be built as a module. If so, the module
+ will be called bd71815-regulator.
+
config REGULATOR_BD71828
tristate "ROHM BD71828 Power Regulator"
depends on MFD_ROHM_BD71828
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 44d2f8bf4b74..c6f84a332fdd 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -30,6 +30,7 @@ obj-$(CONFIG_REGULATOR_ATC260X) += atc260x-regulator.o
obj-$(CONFIG_REGULATOR_AXP20X) += axp20x-regulator.o
obj-$(CONFIG_REGULATOR_BCM590XX) += bcm590xx-regulator.o
obj-$(CONFIG_REGULATOR_BD70528) += bd70528-regulator.o
+obj-$(CONFIG_REGULATOR_BD71815) += bd71815-regulator.o
obj-$(CONFIG_REGULATOR_BD71828) += bd71828-regulator.o
obj-$(CONFIG_REGULATOR_BD718XX) += bd718x7-regulator.o
obj-$(CONFIG_REGULATOR_BD9571MWV) += bd9571mwv-regulator.o
diff --git a/drivers/regulator/bd71815-regulator.c b/drivers/regulator/bd71815-regulator.c
new file mode 100644
index 000000000000..a4e8d5e36b40
--- /dev/null
+++ b/drivers/regulator/bd71815-regulator.c
@@ -0,0 +1,652 @@
+// SPDX-License-Identifier: GPL-2.0-only
+//
+// Copyright 2014 Embest Technology Co. Ltd. Inc.
+// bd71815-regulator.c ROHM BD71815 regulator driver
+//
+// Author: Tony Luo <luofc@embedinfo.com>
+//
+// Partially rewritten at 2021 by
+// Matti Vaittinen <matti.vaitinen@fi.rohmeurope.com>
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/gpio.h>
+#include <linux/mfd/rohm-generic.h>
+#include <linux/mfd/rohm-bd71815.h>
+#include <linux/regulator/of_regulator.h>
+
+struct bd71815_regulator {
+ struct regulator_desc desc;
+ const struct rohm_dvs_config *dvs;
+};
+
+struct bd71815_pmic {
+ struct bd71815_regulator descs[BD71815_REGULATOR_CNT];
+ struct regmap *regmap;
+ struct device *dev;
+ struct gpio_descs *gps;
+ struct regulator_dev *rdev[BD71815_REGULATOR_CNT];
+};
+
+static const int bd7181x_wled_currents[] = {
+ 10, 20, 30, 50, 70, 100, 200, 300, 500, 700, 1000, 2000, 3000, 4000,
+ 5000, 6000, 7000, 8000, 9000, 10000, 11000, 12000, 13000, 14000, 15000,
+ 16000, 17000, 18000, 19000, 20000, 21000, 22000, 23000, 24000, 25000,
+};
+
+static const struct rohm_dvs_config buck1_dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
+ ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD71815_REG_BUCK1_VOLT_H,
+ .run_mask = BD71815_VOLT_MASK,
+ .run_on_mask = BD71815_BUCK_RUN_ON,
+ .snvs_on_mask = BD71815_BUCK_SNVS_ON,
+ .suspend_reg = BD71815_REG_BUCK1_VOLT_L,
+ .suspend_mask = BD71815_VOLT_MASK,
+ .suspend_on_mask = BD71815_BUCK_SUSP_ON,
+ .lpsr_reg = BD71815_REG_BUCK1_VOLT_L,
+ .lpsr_mask = BD71815_VOLT_MASK,
+ .lpsr_on_mask = BD71815_BUCK_LPSR_ON,
+};
+
+static const struct rohm_dvs_config buck2_dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
+ ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD71815_REG_BUCK2_VOLT_H,
+ .run_mask = BD71815_VOLT_MASK,
+ .run_on_mask = BD71815_BUCK_RUN_ON,
+ .snvs_on_mask = BD71815_BUCK_SNVS_ON,
+ .suspend_reg = BD71815_REG_BUCK2_VOLT_L,
+ .suspend_mask = BD71815_VOLT_MASK,
+ .suspend_on_mask = BD71815_BUCK_SUSP_ON,
+ .lpsr_reg = BD71815_REG_BUCK2_VOLT_L,
+ .lpsr_mask = BD71815_VOLT_MASK,
+ .lpsr_on_mask = BD71815_BUCK_LPSR_ON,
+};
+
+static const struct rohm_dvs_config buck3_dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
+ ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD71815_REG_BUCK3_VOLT,
+ .run_mask = BD71815_VOLT_MASK,
+ .run_on_mask = BD71815_BUCK_RUN_ON,
+ .snvs_on_mask = BD71815_BUCK_SNVS_ON,
+ .suspend_on_mask = BD71815_BUCK_SUSP_ON,
+ .lpsr_on_mask = BD71815_BUCK_LPSR_ON,
+};
+
+static const struct rohm_dvs_config buck4_dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
+ ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD71815_REG_BUCK4_VOLT,
+ .run_mask = BD71815_VOLT_MASK,
+ .run_on_mask = BD71815_BUCK_RUN_ON,
+ .snvs_on_mask = BD71815_BUCK_SNVS_ON,
+ .suspend_on_mask = BD71815_BUCK_SUSP_ON,
+ .lpsr_on_mask = BD71815_BUCK_LPSR_ON,
+};
+
+static const struct rohm_dvs_config ldo1_dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
+ ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD71815_REG_LDO_MODE1,
+ .run_mask = BD71815_VOLT_MASK,
+ .run_on_mask = LDO1_RUN_ON,
+ .snvs_on_mask = LDO1_SNVS_ON,
+ .suspend_on_mask = LDO1_SUSP_ON,
+ .lpsr_on_mask = LDO1_LPSR_ON,
+};
+
+static const struct rohm_dvs_config ldo2_dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
+ ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD71815_REG_LDO_MODE2,
+ .run_mask = BD71815_VOLT_MASK,
+ .run_on_mask = LDO2_RUN_ON,
+ .snvs_on_mask = LDO2_SNVS_ON,
+ .suspend_on_mask = LDO2_SUSP_ON,
+ .lpsr_on_mask = LDO2_LPSR_ON,
+};
+
+static const struct rohm_dvs_config ldo3_dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
+ ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD71815_REG_LDO_MODE2,
+ .run_mask = BD71815_VOLT_MASK,
+ .run_on_mask = LDO3_RUN_ON,
+ .snvs_on_mask = LDO3_SNVS_ON,
+ .suspend_on_mask = LDO3_SUSP_ON,
+ .lpsr_on_mask = LDO3_LPSR_ON,
+};
+
+static const struct rohm_dvs_config ldo4_dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
+ ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD71815_REG_LDO_MODE3,
+ .run_mask = BD71815_VOLT_MASK,
+ .run_on_mask = LDO4_RUN_ON,
+ .snvs_on_mask = LDO4_SNVS_ON,
+ .suspend_on_mask = LDO4_SUSP_ON,
+ .lpsr_on_mask = LDO4_LPSR_ON,
+};
+
+static const struct rohm_dvs_config ldo5_dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
+ ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD71815_REG_LDO_MODE3,
+ .run_mask = BD71815_VOLT_MASK,
+ .run_on_mask = LDO5_RUN_ON,
+ .snvs_on_mask = LDO5_SNVS_ON,
+ .suspend_on_mask = LDO5_SUSP_ON,
+ .lpsr_on_mask = LDO5_LPSR_ON,
+};
+
+static const struct rohm_dvs_config dvref_dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
+ ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
+ .run_on_mask = DVREF_RUN_ON,
+ .snvs_on_mask = DVREF_SNVS_ON,
+ .suspend_on_mask = DVREF_SUSP_ON,
+ .lpsr_on_mask = DVREF_LPSR_ON,
+};
+
+static const struct rohm_dvs_config ldolpsr_dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
+ ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
+ .run_on_mask = DVREF_RUN_ON,
+ .snvs_on_mask = DVREF_SNVS_ON,
+ .suspend_on_mask = DVREF_SUSP_ON,
+ .lpsr_on_mask = DVREF_LPSR_ON,
+};
+
+static const struct rohm_dvs_config buck5_dvs = {
+ .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS |
+ ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR,
+ .run_reg = BD71815_REG_BUCK5_VOLT,
+ .run_mask = BD71815_VOLT_MASK,
+ .run_on_mask = BD71815_BUCK_RUN_ON,
+ .snvs_on_mask = BD71815_BUCK_SNVS_ON,
+ .suspend_on_mask = BD71815_BUCK_SUSP_ON,
+ .lpsr_on_mask = BD71815_BUCK_LPSR_ON,
+};
+
+static int set_hw_dvs_levels(struct device_node *np,
+ const struct regulator_desc *desc,
+ struct regulator_config *cfg)
+{
+ struct bd71815_regulator *data;
+
+ data = container_of(desc, struct bd71815_regulator, desc);
+ return rohm_regulator_set_dvs_levels(data->dvs, np, desc, cfg->regmap);
+}
+
+/*
+ * Bucks 1 and 2 have two voltage selection registers where selected
+ * voltage can be set. Which of the registers is used can be either controlled
+ * by a control bit in register - or by HW state. If HW state specific voltages
+ * are given - then we assume HW state based control should be used.
+ *
+ * If volatge value is updated to currently selected register - then output
+ * voltage is immediately changed no matter what is set as ramp rate. Thus we
+ * default changing voltage by writing new value to inactive register and
+ * then updating the 'register selection' bit. This naturally only works when
+ * HW state machine is not used to select the voltage.
+ */
+static int buck12_set_hw_dvs_levels(struct device_node *np,
+ const struct regulator_desc *desc,
+ struct regulator_config *cfg)
+{
+ struct bd71815_regulator *data;
+ int ret = 0, val;
+
+ data = container_of(desc, struct bd71815_regulator, desc);
+
+ if (of_find_property(np, "rohm,dvs-run-voltage", NULL) ||
+ of_find_property(np, "rohm,dvs-suspend-voltage", NULL) ||
+ of_find_property(np, "rohm,dvs-lpsr-voltage", NULL) ||
+ of_find_property(np, "rohm,dvs-snvs-voltage", NULL)) {
+ ret = regmap_read(cfg->regmap, desc->vsel_reg, &val);
+ if (ret)
+ return ret;
+
+ if (!(BD71815_BUCK_STBY_DVS & val) &&
+ !(BD71815_BUCK_DVSSEL & val)) {
+ int val2;
+
+ /*
+ * We are currently using voltage from _L.
+ * We'd better copy it to _H and switch to it to
+ * avoid shutting us down if LPSR or SUSPEND is set to
+ * disabled. _L value is at reg _H + 1
+ */
+ ret = regmap_read(cfg->regmap, desc->vsel_reg + 1,
+ &val2);
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(cfg->regmap, desc->vsel_reg,
+ BD71815_VOLT_MASK |
+ BD71815_BUCK_DVSSEL,
+ val2 | BD71815_BUCK_DVSSEL);
+ if (ret)
+ return ret;
+ }
+ ret = rohm_regulator_set_dvs_levels(data->dvs, np, desc,
+ cfg->regmap);
+ if (ret)
+ return ret;
+ /*
+ * DVS levels were given => use HW-state machine for voltage
+ * controls. NOTE: AFAIK, This means that if voltage is changed
+ * by SW the ramp-rate is not respected. Should we disable
+ * SW voltage control when the HW state machine is used?
+ */
+ ret = regmap_update_bits(cfg->regmap, desc->vsel_reg,
+ BD71815_BUCK_STBY_DVS,
+ BD71815_BUCK_STBY_DVS);
+ }
+
+ return ret;
+}
+
+/*
+ * BUCK1/2
+ * BUCK1RAMPRATE[1:0] BUCK1 DVS ramp rate setting
+ * 00: 10.00mV/usec 10mV 1uS
+ * 01: 5.00mV/usec 10mV 2uS
+ * 10: 2.50mV/usec 10mV 4uS
+ * 11: 1.25mV/usec 10mV 8uS
+ */
+static const unsigned int bd7181x_ramp_table[] = { 1250, 2500, 5000, 10000 };
+
+static int bd7181x_led_set_current_limit(struct regulator_dev *rdev,
+ int min_uA, int max_uA)
+{
+ int ret;
+ int onstatus;
+
+ onstatus = regulator_is_enabled_regmap(rdev);
+
+ ret = regulator_set_current_limit_regmap(rdev, min_uA, max_uA);
+ if (!ret) {
+ int newstatus;
+
+ newstatus = regulator_is_enabled_regmap(rdev);
+ if (onstatus != newstatus) {
+ /*
+ * HW FIX: spurious led status change detected. Toggle
+ * state as a workaround
+ */
+ if (onstatus)
+ ret = regulator_enable_regmap(rdev);
+ else
+ ret = regulator_disable_regmap(rdev);
+
+ if (ret)
+ dev_err(rdev_get_dev(rdev),
+ "failed to revert the LED state (%d)\n",
+ ret);
+ }
+ }
+
+ return ret;
+}
+
+static int bd7181x_buck12_get_voltage_sel(struct regulator_dev *rdev)
+{
+ struct bd71815_pmic *pmic = rdev_get_drvdata(rdev);
+ int rid = rdev_get_id(rdev);
+ int ret, regh, regl, val;
+
+ regh = BD71815_REG_BUCK1_VOLT_H + rid * 0x2;
+ regl = BD71815_REG_BUCK1_VOLT_L + rid * 0x2;
+
+ ret = regmap_read(pmic->regmap, regh, &val);
+ if (ret)
+ return ret;
+
+ /*
+ * If we use HW state machine based voltage reg selection - then we
+ * return BD71815_REG_BUCK1_VOLT_H which is used at RUN.
+ * Else we do return the BD71815_REG_BUCK1_VOLT_H or
+ * BD71815_REG_BUCK1_VOLT_L depending on which is selected to be used
+ * by BD71815_BUCK_DVSSEL bit
+ */
+ if ((!(val & BD71815_BUCK_STBY_DVS)) && (!(val & BD71815_BUCK_DVSSEL)))
+ ret = regmap_read(pmic->regmap, regl, &val);
+
+ if (ret)
+ return ret;
+
+ return val & BD71815_VOLT_MASK;
+}
+
+/*
+ * For Buck 1/2.
+ */
+static int bd7181x_buck12_set_voltage_sel(struct regulator_dev *rdev,
+ unsigned int sel)
+{
+ struct bd71815_pmic *pmic = rdev_get_drvdata(rdev);
+ int rid = rdev_get_id(rdev);
+ int ret, val, reg, regh, regl;
+
+ regh = BD71815_REG_BUCK1_VOLT_H + rid*0x2;
+ regl = BD71815_REG_BUCK1_VOLT_L + rid*0x2;
+
+ ret = regmap_read(pmic->regmap, regh, &val);
+ if (ret)
+ return ret;
+
+ /*
+ * If bucks 1 & 2 are controlled by state machine - then the RUN state
+ * voltage is set to BD71815_REG_BUCK1_VOLT_H. Changing SUSPEND/LPSR
+ * voltages at runtime is not supported by this driver.
+ */
+ if (((val & BD71815_BUCK_STBY_DVS))) {
+ return regmap_update_bits(pmic->regmap, regh, BD71815_VOLT_MASK,
+ sel);
+ }
+ /* Update new voltage to the register which is not selected now */
+ if (val & BD71815_BUCK_DVSSEL)
+ reg = regl;
+ else
+ reg = regh;
+
+ ret = regmap_update_bits(pmic->regmap, reg, BD71815_VOLT_MASK, sel);
+ if (ret)
+ return ret;
+
+ /* Select the other DVS register to be used */
+ return regmap_update_bits(pmic->regmap, regh, BD71815_BUCK_DVSSEL, ~val);
+}
+
+static const struct regulator_ops bd7181x_ldo_regulator_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+};
+
+static const struct regulator_ops bd7181x_fixed_regulator_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear,
+};
+
+static const struct regulator_ops bd7181x_buck_regulator_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+};
+
+static const struct regulator_ops bd7181x_buck12_regulator_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear,
+ .set_voltage_sel = bd7181x_buck12_set_voltage_sel,
+ .get_voltage_sel = bd7181x_buck12_get_voltage_sel,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .set_ramp_delay = regulator_set_ramp_delay_regmap,
+};
+
+static const struct regulator_ops bd7181x_led_regulator_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .set_current_limit = bd7181x_led_set_current_limit,
+ .get_current_limit = regulator_get_current_limit_regmap,
+};
+
+#define BD71815_FIXED_REG(_name, _id, ereg, emsk, voltage, _dvs) \
+ [(_id)] = { \
+ .desc = { \
+ .name = #_name, \
+ .of_match = of_match_ptr(#_name), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .n_voltages = 1, \
+ .ops = &bd7181x_fixed_regulator_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = (_id), \
+ .owner = THIS_MODULE, \
+ .min_uV = (voltage), \
+ .enable_reg = (ereg), \
+ .enable_mask = (emsk), \
+ .of_parse_cb = set_hw_dvs_levels, \
+ }, \
+ .dvs = (_dvs), \
+ }
+
+#define BD71815_BUCK_REG(_name, _id, vsel, ereg, min, max, step, _dvs) \
+ [(_id)] = { \
+ .desc = { \
+ .name = #_name, \
+ .of_match = of_match_ptr(#_name), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .n_voltages = ((max) - (min)) / (step) + 1, \
+ .ops = &bd7181x_buck_regulator_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = (_id), \
+ .owner = THIS_MODULE, \
+ .min_uV = (min), \
+ .uV_step = (step), \
+ .vsel_reg = (vsel), \
+ .vsel_mask = BD71815_VOLT_MASK, \
+ .enable_reg = (ereg), \
+ .enable_mask = BD71815_BUCK_RUN_ON, \
+ .of_parse_cb = set_hw_dvs_levels, \
+ }, \
+ .dvs = (_dvs), \
+ }
+
+#define BD71815_BUCK12_REG(_name, _id, vsel, ereg, min, max, step, \
+ _dvs) \
+ [(_id)] = { \
+ .desc = { \
+ .name = #_name, \
+ .of_match = of_match_ptr(#_name), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .n_voltages = ((max) - (min)) / (step) + 1, \
+ .ops = &bd7181x_buck12_regulator_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = (_id), \
+ .owner = THIS_MODULE, \
+ .min_uV = (min), \
+ .uV_step = (step), \
+ .vsel_reg = (vsel), \
+ .vsel_mask = 0x3f, \
+ .enable_reg = (ereg), \
+ .enable_mask = 0x04, \
+ .ramp_reg = (ereg), \
+ .ramp_mask = BD71815_BUCK_RAMPRATE_MASK, \
+ .ramp_delay_table = bd7181x_ramp_table, \
+ .n_ramp_values = ARRAY_SIZE(bd7181x_ramp_table),\
+ .of_parse_cb = buck12_set_hw_dvs_levels, \
+ }, \
+ .dvs = (_dvs), \
+ }
+
+#define BD71815_LED_REG(_name, _id, csel, mask, ereg, emsk, currents) \
+ [(_id)] = { \
+ .desc = { \
+ .name = #_name, \
+ .of_match = of_match_ptr(#_name), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .n_current_limits = ARRAY_SIZE(currents), \
+ .ops = &bd7181x_led_regulator_ops, \
+ .type = REGULATOR_CURRENT, \
+ .id = (_id), \
+ .owner = THIS_MODULE, \
+ .curr_table = currents, \
+ .csel_reg = (csel), \
+ .csel_mask = (mask), \
+ .enable_reg = (ereg), \
+ .enable_mask = (emsk), \
+ }, \
+ }
+
+#define BD71815_LDO_REG(_name, _id, vsel, ereg, emsk, min, max, step, \
+ _dvs) \
+ [(_id)] = { \
+ .desc = { \
+ .name = #_name, \
+ .of_match = of_match_ptr(#_name), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .n_voltages = ((max) - (min)) / (step) + 1, \
+ .ops = &bd7181x_ldo_regulator_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = (_id), \
+ .owner = THIS_MODULE, \
+ .min_uV = (min), \
+ .uV_step = (step), \
+ .vsel_reg = (vsel), \
+ .vsel_mask = BD71815_VOLT_MASK, \
+ .enable_reg = (ereg), \
+ .enable_mask = (emsk), \
+ .of_parse_cb = set_hw_dvs_levels, \
+ }, \
+ .dvs = (_dvs), \
+ }
+
+static struct bd71815_regulator bd71815_regulators[] = {
+ BD71815_BUCK12_REG(buck1, BD71815_BUCK1, BD71815_REG_BUCK1_VOLT_H,
+ BD71815_REG_BUCK1_MODE, 800000, 2000000, 25000,
+ &buck1_dvs),
+ BD71815_BUCK12_REG(buck2, BD71815_BUCK2, BD71815_REG_BUCK2_VOLT_H,
+ BD71815_REG_BUCK2_MODE, 800000, 2000000, 25000,
+ &buck2_dvs),
+ BD71815_BUCK_REG(buck3, BD71815_BUCK3, BD71815_REG_BUCK3_VOLT,
+ BD71815_REG_BUCK3_MODE, 1200000, 2700000, 50000,
+ &buck3_dvs),
+ BD71815_BUCK_REG(buck4, BD71815_BUCK4, BD71815_REG_BUCK4_VOLT,
+ BD71815_REG_BUCK4_MODE, 1100000, 1850000, 25000,
+ &buck4_dvs),
+ BD71815_BUCK_REG(buck5, BD71815_BUCK5, BD71815_REG_BUCK5_VOLT,
+ BD71815_REG_BUCK5_MODE, 1800000, 3300000, 50000,
+ &buck5_dvs),
+ BD71815_LDO_REG(ldo1, BD71815_LDO1, BD71815_REG_LDO1_VOLT,
+ BD71815_REG_LDO_MODE1, LDO1_RUN_ON, 800000, 3300000,
+ 50000, &ldo1_dvs),
+ BD71815_LDO_REG(ldo2, BD71815_LDO2, BD71815_REG_LDO2_VOLT,
+ BD71815_REG_LDO_MODE2, LDO2_RUN_ON, 800000, 3300000,
+ 50000, &ldo2_dvs),
+ /*
+ * Let's default LDO3 to be enabled by SW. We can override ops if DT
+ * says LDO3 should be enabled by HW when DCIN is connected.
+ */
+ BD71815_LDO_REG(ldo3, BD71815_LDO3, BD71815_REG_LDO3_VOLT,
+ BD71815_REG_LDO_MODE2, LDO3_RUN_ON, 800000, 3300000,
+ 50000, &ldo3_dvs),
+ BD71815_LDO_REG(ldo4, BD71815_LDO4, BD71815_REG_LDO4_VOLT,
+ BD71815_REG_LDO_MODE3, LDO4_RUN_ON, 800000, 3300000,
+ 50000, &ldo4_dvs),
+ BD71815_LDO_REG(ldo5, BD71815_LDO5, BD71815_REG_LDO5_VOLT_H,
+ BD71815_REG_LDO_MODE3, LDO5_RUN_ON, 800000, 3300000,
+ 50000, &ldo5_dvs),
+ BD71815_FIXED_REG(ldodvref, BD71815_LDODVREF, BD71815_REG_LDO_MODE4,
+ DVREF_RUN_ON, 3000000, &dvref_dvs),
+ BD71815_FIXED_REG(ldolpsr, BD71815_LDOLPSR, BD71815_REG_LDO_MODE4,
+ LDO_LPSR_RUN_ON, 1800000, &ldolpsr_dvs),
+ BD71815_LED_REG(wled, BD71815_WLED, BD71815_REG_LED_DIMM, LED_DIMM_MASK,
+ BD71815_REG_LED_CTRL, LED_RUN_ON,
+ bd7181x_wled_currents),
+};
+
+static int bd7181x_probe(struct platform_device *pdev)
+{
+ struct bd71815_pmic *pmic;
+ struct regulator_config config = {};
+ int i, ret;
+ struct gpio_desc *ldo4_en;
+
+ pmic = devm_kzalloc(&pdev->dev, sizeof(*pmic), GFP_KERNEL);
+ if (!pmic)
+ return -ENOMEM;
+
+ memcpy(pmic->descs, bd71815_regulators, sizeof(pmic->descs));
+
+ pmic->dev = &pdev->dev;
+ pmic->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!pmic->regmap) {
+ dev_err(pmic->dev, "No parent regmap\n");
+ return -ENODEV;
+ }
+ platform_set_drvdata(pdev, pmic);
+ ldo4_en = devm_gpiod_get_from_of_node(&pdev->dev,
+ pdev->dev.parent->of_node,
+ "rohm,vsel-gpios", 0,
+ GPIOD_ASIS, "ldo4-en");
+
+ if (IS_ERR(ldo4_en)) {
+ ret = PTR_ERR(ldo4_en);
+ if (ret != -ENOENT)
+ return ret;
+ ldo4_en = NULL;
+ }
+
+ /* Disable to go to ship-mode */
+ ret = regmap_update_bits(pmic->regmap, BD71815_REG_PWRCTRL,
+ RESTARTEN, 0);
+ if (ret)
+ return ret;
+
+ config.dev = pdev->dev.parent;
+ config.regmap = pmic->regmap;
+
+ for (i = 0; i < BD71815_REGULATOR_CNT; i++) {
+ struct regulator_desc *desc;
+ struct regulator_dev *rdev;
+
+ desc = &pmic->descs[i].desc;
+ if (i == BD71815_LDO4)
+ config.ena_gpiod = ldo4_en;
+
+ config.driver_data = pmic;
+
+ rdev = devm_regulator_register(&pdev->dev, desc, &config);
+ if (IS_ERR(rdev)) {
+ dev_err(&pdev->dev,
+ "failed to register %s regulator\n",
+ desc->name);
+ return PTR_ERR(rdev);
+ }
+ config.ena_gpiod = NULL;
+ pmic->rdev[i] = rdev;
+ }
+ return 0;
+}
+
+static const struct platform_device_id bd7181x_pmic_id[] = {
+ { "bd71815-pmic", ROHM_CHIP_TYPE_BD71815 },
+ { },
+};
+MODULE_DEVICE_TABLE(platform, bd7181x_pmic_id);
+
+static struct platform_driver bd7181x_regulator = {
+ .driver = {
+ .name = "bd7181x-pmic",
+ .owner = THIS_MODULE,
+ },
+ .probe = bd7181x_probe,
+ .id_table = bd7181x_pmic_id,
+};
+module_platform_driver(bd7181x_regulator);
+
+MODULE_AUTHOR("Tony Luo <luofc@embedinfo.com>");
+MODULE_DESCRIPTION("BD71815 voltage regulator driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:bd7181x-pmic");
--
2.25.4
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
next prev parent reply other threads:[~2021-04-05 11:44 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-04-05 11:40 [PATCH v6 00/16] Support ROHM BD71815 PMIC Matti Vaittinen
2021-04-05 11:40 ` [PATCH v6 01/16] rtc: bd70528: Do not require parent data Matti Vaittinen
2021-04-05 11:40 ` [PATCH v6 02/16] mfd: bd718x7: simplify by cleaning unnecessary device data Matti Vaittinen
2021-04-05 11:41 ` [PATCH v6 03/16] dt_bindings: bd71828: Add clock output mode Matti Vaittinen
2021-04-05 11:41 ` [PATCH v6 04/16] dt_bindings: regulator: Add ROHM BD71815 PMIC regulators Matti Vaittinen
2021-04-05 11:41 ` [PATCH v6 05/16] dt_bindings: mfd: Add ROHM BD71815 PMIC Matti Vaittinen
2021-04-05 11:42 ` [PATCH v6 06/16] mfd: Add ROHM BD71815 ID Matti Vaittinen
2021-04-05 11:42 ` [PATCH v6 07/16] mfd: Sort ROHM chip ID list for better readability Matti Vaittinen
2021-04-05 11:42 ` [PATCH v6 08/16] mfd: Support for ROHM BD71815 PMIC core Matti Vaittinen
2021-04-05 11:43 ` [PATCH v6 09/16] gpio: support ROHM BD71815 GPOs Matti Vaittinen
2021-04-05 11:43 ` [PATCH v6 10/16] regulator: rohm-regulator: linear voltage support Matti Vaittinen
2021-04-05 11:43 ` [PATCH v6 11/16] regulator: rohm-regulator: Support SNVS HW state Matti Vaittinen
2021-04-05 11:44 ` [PATCH v6 12/16] regulator: bd718x7, bd71828: Use ramp-delay helper Matti Vaittinen
2021-04-05 11:44 ` Matti Vaittinen [this message]
2021-04-05 11:44 ` [PATCH v6 14/16] clk: bd718x7: Add support for clk gate on ROHM BD71815 PMIC Matti Vaittinen
2021-04-05 11:44 ` [PATCH v6 15/16] rtc: bd70528: Support RTC on ROHM BD71815 Matti Vaittinen
2021-04-05 11:45 ` [PATCH v6 16/16] MAINTAINERS: Add ROHM BD71815AGW Matti Vaittinen
2021-04-14 13:11 ` [GIT PULL] Immutable branch between MFD, Clock, GPIO, Regulator and RTC due for the v5.13 merge window Lee Jones
2021-04-14 14:53 ` Lee Jones
2021-04-14 17:09 ` Vaittinen, Matti
2021-04-14 17:15 ` Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=9964349abe1c3e5fe06f71019d86ba1a967d01a8.1617616855.git.matti.vaittinen@fi.rohmeurope.com \
--to=matti.vaittinen@fi.rohmeurope.com \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=lee.jones@linaro.org \
--cc=lgirdwood@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-power@fi.rohmeurope.com \
--cc=mazziesaccount@gmail.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.