From: "Sireesh Kodali" <sireeshkodali1@gmail.com>
To: "Krzysztof Kozlowski" <krzysztof.kozlowski@linaro.org>,
<linux-remoteproc@vger.kernel.org>
Cc: <linux-arm-msm@vger.kernel.org>,
<~postmarketos/upstreaming@lists.sr.ht>,
<bjorn.andersson@linaro.org>, <devicetree@vger.kernel.org>,
<phone-devel@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
"Andy Gross" <agross@kernel.org>,
"Mathieu Poirier" <mathieu.poirier@linaro.org>,
"Rob Herring" <robh+dt@kernel.org>,
"Krzysztof Kozlowski" <krzysztof.kozlowski+dt@linaro.org>
Subject: Re: [PATCH 6/9] dt-bindings: remoteproc: qcom: mss: Convert bindings to YAML
Date: Thu, 12 May 2022 15:20:59 +0530 [thread overview]
Message-ID: <CJXOUUY3IV5I.33259TNMB50JG@skynet-linux> (raw)
In-Reply-To: <29a8871f-59ab-05f2-d258-eea52b7ac6ee@linaro.org>
On Wed May 11, 2022 at 11:20 PM IST, Krzysztof Kozlowski wrote:
> On 11/05/2022 18:15, Sireesh Kodali wrote:
> > Convert the bindings to YAML from txt. The bindings follow a similar
> > schema to `qcom,adsp.yaml`.
> >
> > Signed-off-by: Sireesh Kodali <sireeshkodali1@gmail.com>
> > ---
> > .../bindings/remoteproc/qcom,q6v5.txt | 302 --------
> > .../bindings/remoteproc/qcom,q6v5.yaml | 702 ++++++++++++++++++
> > 2 files changed, 702 insertions(+), 302 deletions(-)
> > delete mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
> > create mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,q6v5.yaml
>
> Same comments as for patch 4 apply here. Some of them seems fixed so it
> makes me wonder - why you wrote two bindings in entirely different way?
>
This was largely based on the existing qcom,adsp.yaml. That's probably
why there are less mistakes.
> > + This document defines the binding for a component that loads and boots firmware
> > + on the Qualcomm Hexagon core.
> > +
> > +properties:
> > + compatible:
> > + # Special case, because older platforms like MSM8916 use both compatibles together
> > + minItems: 1
> > + maxItems: 2
> > + oneOf:
> > + - items:
> > + - enum:
> > + - qcom,msm8916-mss-pil
> > + - enum:
> > + - qcom,q6v5-pil
>
> Everywhere - same comments as in patch 4.
>
Will be fixed in v2.
> > + - items:
> > + - enum:
> > + - qcom,q6v5-pil
> > + - qcom,ipq8074-wcss-pil
> > + - qcom,qcs404-wcss-pil
> > + - qcom,msm8916-mss-pil
> > + - qcom,msm8974-mss-pil
> > + - qcom,msm8996-mss-pil
> > + - qcom,msm8998-mss-pil
> > + - qcom,sc7180-mss-pil
> > + - qcom,sc7280-mss-pil
> > + - qcom,sdm845-mss-pil
> > +
> > + reg:
> > + description: must specify the base address and size of the qdsp6 and rmb
> > + register blocks
> > + maxItems: 2
> > +
> > + reg-names:
> > + items:
> > + - const: qdsp6
> > + - const: rmb
> > +
> > + interrupts-extended:
> > + minItems: 5
> > + maxItems: 6
> > +
> > + interrupt-names:
> > + minItems: 5
> > + maxItems: 6
> > +
> > + firmware-name:
> > + $ref: /schemas/types.yaml#/definitions/string-array
> > + description: List the relative firmware image paths for the mba and
> > + modem. They are used for booting and authenticating the Hexagon core.
> > + maxItems: 2
> > +
> > + clocks:
> > + minItems: 4
> > + maxItems: 10
> > +
> > + clock-names:
> > + minItems: 4
> > + maxItems: 10
> > +
> > + resets:
> > + description: Reference to the reset-controllwer for the modem subsystem
> > + minItems: 1
> > + maxItems: 3
> > +
> > + reset-names:
> > + minItems: 1
> > + maxItems: 3
> > +
> > + memory-region:
> > + maxItems: 1
> > + description: Reference to the reserved-memory for the mba region followed
> > + by the mpss region. Required if the mba and mpss sub-nodes are not
> > + specified.
> > +
> > + cx-supply:
> > + description: Phandle to the CX regulator
> > +
> > + mx-supply:
> > + description: Phandle to the MX regulator
> > +
> > + pll-supply:
> > + description: Phandle to the PLL regulator, to be held on behalf of the
> > + booting Hexagon core
> > +
> > + mss-supply:
> > + description: Phandle to the mss regulator, to be held on behalf of the
> > + booting Hexagon core
>
> s/Phandle to//, everywhere.
>
> > +
> > + power-domains:
> > + minItems: 1
> > + maxItems: 4
> > +
> > + power-domain-names:
> > + minItems: 1
> > + maxItems: 4
> > +
> > + qcom,qmp:
> > + $ref: /schemas/types.yaml#/definitions/phandle
> > + description: Reference to the AOSS side-channel message RAM.
> > +
> > + qcom,smem-states:
> > + $ref: /schemas/types.yaml#/definitions/phandle-array
> > + description: States used by the AP to signal the Hexagon core
> > + items:
> > + - description: Stop the modem
> > +
> > + qcom,smem-state-names:
> > + $ref: /schemas/types.yaml#/definitions/string-array
> > + description: The names of the state bits used for SMP2P output
> > + items:
> > + - const: stop
> > +
> > + qcom,halt-regs:
> > + $ref: /schemas/types.yaml#/definitions/phandle-array
> > + description:
> > + Phandle reference to a syscon representing TCSR followed by the
> > + three offsets within syscon for q6, modem and nc halt registers.
> > +
> > + qcom,spare-regs:
> > + $ref: /schemas/types.yaml#/definitions/phandle-array
> > + description:
> > + A phandle reference to a syscon representing TCSR followed by the
> > + offset within syscon for conn_box_spare0 register used by the modem
> > + sub-system running on SC7180 SoC.
> > +
> > + qcom,ext-regs:
> > + $ref: /schemas/types.yaml#/definitions/phandle-array
> > + description:
> > + Two phandle references to syscons representing TCSR_REG and TCSR
> > + register space followed by the two offsets within the syscon to
> > + force_clk_en/rscc_disable and axim1_clk_off/crypto_clk_off registers
> > + respectively.
> > +
> > + qcom,qaccept-regs:
> > + $ref: /schemas/types.yaml#/definitions/phandle-array
> > + description:
> > + A phandle reference to a syscon representing TCSR followed by the three
> > + offsets within syscon for mdm, cx and axi qaccept registers used by the
> > + modem sub-system running on SC7280 SoC.
> > +
> > + iommus:
> > + description:
> > + Only required on platforms that do not have TrustZone.
> > +
> > + smd-edge:
> > + type: object
> > + description:
> > + Qualcomm Shared Memory subnode which represents communication edge,
> > + channels and devices related to the ADSP.
> > +
> > + glink-edge:
> > + type: object
> > + description:
> > + Qualcomm G-Link subnode which represents communication edge, channels
> > + and devices related to the ADSP.
> > +
> > + mba:
> > + type: object
>
> description needed.
>
> > + properties:
> > + memory-region:
> > + maxItems: 1
> > +
> > + required:
> > + - memory-region
> > +
> > + mpss:
>
> description needed.
>
> > + type: object
> > + properties:
> > + memory-region:
> > + maxItems: 1
> > +
> > + required:
> > + - memory-region
> > +
> > +required:
> > + - compatible
> > + - clocks
> > + - clock-names
> > + - interrupts-extended
> > + - interrupt-names
> > + - qcom,smem-states
> > + - qcom,smem-state-names
> > +
> > +additionalProperties: false
> > +
> > +allOf:
> > + - if:
> > + properties:
> > + compatible:
> > + contains:
> > + enum:
> > + - qcom,ipq8074-wcss-pil
> > + then:
> > + properties:
> > + clocks: false
> > + clock-names: false
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + contains:
> > + enum:
> > + - qcom,qcs404-wcss-pil
> > + then:
> > + properties:
> > + clocks:
> > + items:
> > + - description: GCC_AHBS_CBCR clock
> > + - description: GCC_AXIM_CBCR clock
> > + - description: LCC_AHBFABRIC_CBC clock
> > + - description: TCSR_LCC_CBC clock
> > + - description: LCC_AHBS_CBC clock
> > + - description: LCC_TCM_SLAVE_CBC clock
> > + - description: LCC_ABHM_CBC clock
> > + - description: LCC_AXIM_CBC clock
> > + - description: LCC_BCR_SLEEP clock
> > + - description: XO clock
> > + clock-names:
> > + items:
> > + - const: gcc_ahbs_cbcr
> > + - const: gcc_axim_cbcr
> > + - const: lcc_ahbfabric_cbc
> > + - const: tcsr_lcc_cbc
> > + - const: lcc_abhs_cbc
> > + - const: lcc_tcm_slave_cbc
> > + - const: lcc_abhm_cbc
> > + - const: lcc_axim_cbc
> > + - const: lcc_bcr_sleep
> > + - const: xo
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + contains:
> > + enum:
> > + - qcom,q6v5-pil
> > + - qcom,msm8916-mss-pil
> > + - qcom,msm8974-mss-pil
> > + then:
> > + properties:
> > + clocks:
> > + items:
> > + - description: Interface clock
> > + - description: Bus clock
> > + - description: Memory clock
> > + - description: XO clock
> > + clock-names:
> > + items:
> > + - const: iface
> > + - const: bus
> > + - const: mem
> > + - const: xo
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + contains:
> > + enum:
> > + - qcom,msm8996-mss-pil
> > + then:
> > + properties:
> > + clocks:
> > + items:
> > + - description: Interface clock
> > + - description: Bus clock
> > + - description: Memory clock
> > + - description: GPLL0_MSS clock
> > + - description: SNOC_AXI clock
> > + - description: MNOC_AXI clock
> > + - description: PNOC clock
> > + - description: QDSS clock
> > + - description: XO clock
> > + clock-names:
> > + items:
> > + - const: iface
> > + - const: bus
> > + - const: mem
> > + - const: gpll0_mss
> > + - const: snoc_axi
> > + - const: mnoc_axi
> > + - const: pnoc
> > + - const: qdss
> > + - const: xo
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + contains:
> > + enum:
> > + - qcom,msm8998-mss-pil
> > + then:
> > + properties:
> > + clocks:
> > + items:
> > + - description: Interface clock
> > + - description: Bus clock
> > + - description: Memory clock
> > + - description: GPLL0_MSS clock
> > + - description: SNOC_AXI clock
> > + - description: MNOC_AXI clock
> > + - description: QDSS clock
> > + - description: XO clock
> > + clock-names:
> > + items:
> > + - const: iface
> > + - const: bus
> > + - const: mem
> > + - const: gpll0_mss
> > + - const: snoc_axi
> > + - const: mnoc_axi
> > + - const: qdss
> > + - const: xo
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + contains:
> > + enum:
> > + - qcom,sc7180-mss-pil
> > + then:
> > + properties:
> > + clocks:
> > + items:
> > + - description: Interface clock
> > + - description: Bus clock
> > + - description: NAV clock
> > + - description: SNOC_AXI clock
> > + - description: MNOC_AXI clock
> > + - description: XO clock
> > + clock-names:
> > + items:
> > + - const: iface
> > + - const: bus
> > + - const: nav
> > + - const: snoc_axi
> > + - const: mnoc_axi
> > + - const: xo
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + contains:
> > + enum:
> > + - qcom,sc7280-mss-pil
> > + then:
> > + properties:
> > + clocks:
> > + items:
> > + - description: Interface clock
> > + - description: Offline clock
> > + - description: SNOC_AXI clock
> > + - description: PKA clock
> > + - description: XO clock
> > + clock-names:
> > + items:
> > + - const: iface
> > + - const: offline
> > + - const: snoc_axi
> > + - const: pka
> > + - const: xo
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + contains:
> > + enum:
> > + - qcom,sdm845-mss-pil
> > + then:
> > + properties:
> > + clocks:
> > + items:
> > + - description: Interface clock
> > + - description: Bus clock
> > + - description: Memory clock
> > + - description: GPLL0_MSS clock
> > + - description: SNOC_AXI clock
> > + - description: MNOC_AXI clock
> > + - description: PRNG clock
> > + - description: XO clock
> > + clock-names:
> > + items:
> > + - const: iface
> > + - const: bus
> > + - const: mem
> > + - const: gpll0_mss
> > + - const: snoc_axi
> > + - const: mnoc_axi
> > + - const: prng
> > + - const: xo
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + contains:
> > + enum:
> > + - qcom,q6v5-pil
> > + - qcom,ipq8074-wcss-pil
> > + - qcom,qcs404-wcss-pil
> > + - qcom,msm8916-mss-pil
> > + - qcom,msm8974-mss-pil
> > + then:
> > + properties:
> > + interrupts-extended:
>
> No extended.
>
> > + items:
> > + - description: Watchdog interrupt
> > + - description: Fatal interrupt
> > + - description: Ready interrupt
> > + - description: Handover interrupt
> > + - description: Stop acknowledge interrupt
> > + interrupt-names:
> > + items:
> > + - const: wdog
> > + - const: fatal
> > + - const: ready
> > + - const: handover
> > + - const: stop-ack
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + contains:
> > + enum:
> > + - qcom,msm8996-mss-pil
> > + - qcom,msm8998-mss-pil
> > + - qcom,sc7180-mss-pil
> > + - qcom,sc7280-mss-pil
> > + - qcom,sdm845-mss-pil
> > + then:
> > + properties:
> > + interrupts-extended:
> > + items:
> > + - description: Watchdog interrupt
> > + - description: Fatal interrupt
> > + - description: Ready interrupt
> > + - description: Handover interrupt
> > + - description: Stop acknowledge interrupt
> > + - description: Shutdown acknowledge interrupt
> > + interrupt-names:
> > + items:
> > + - const: wdog
> > + - const: fatal
> > + - const: ready
> > + - const: handover
> > + - const: stop-ack
> > + - const: shutdown-ack
>
> Both ifs should be written differently. Move the bigger list to
> properties with minItems: 5. For qcom,q6v5-pil you set maxItems:5. For
> qcom,msm8996-mss-pil you set minItems:6.
>
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + enum:
> > + - const: qcom,q6v5-pil
> > + - const: qcom,msm8916-mss-pil
> > + - const: qcom,msm8974-mss-pil
> > + then:
> > + properties:
> > + cx-supply:
> > + deprecated: true
> > + mx-supply:
> > + deprecated: true
> > +
> > + required:
> > + - pll-supply
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + enum:
> > + - qcom,msm8916-mss-pil
> > + - qcom,msm8974-mss-pil
> > + - qcom,msm8996-mss-pil
> > + - qcom,msm8998-mss-pil
> > + then:
> > + properties:
> > + power-domains:
> > + items:
> > + - description: CX power domain
> > + - description: MX power domain
> > + power-domain-names:
> > + items:
> > + - const: cx
> > + - const: mx
> > +
> > + required:
> > + - power-domains
> > + - power-domain-names
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + enum:
> > + - const: qcom,msm8996-mss-pil
> > + then:
> > + properties:
> > + cx-supply: false
> > + mx-supply: false
> > +
> > + required:
> > + - pll-supply
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + enum:
> > + - const: qcom,qcs404-wcss-pil
> > + then:
> > + required:
> > + - cx-supply
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + contains:
> > + enum:
> > + - qcom,sdm845-mss-pil
> > + - qcom,sc7180-mss-pil
> > + then:
> > + properties:
> > + power-domains:
> > + items:
> > + - description: CX power domain
> > + - description: MX power domain
> > + - description: MSS power domain
> > + power-domain-names:
> > + items:
> > + - const: cx
> > + - const: mx
> > + - const: mss
> > +
> > + required:
> > + - power-domains
> > + - power-domain-names
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + contains:
> > + enum:
> > + - qcom,sc7280-mss-pil
> > + then:
> > + properties:
> > + power-domains:
> > + items:
> > + - description: CX power domain
> > + - description: MSS power domain
> > + power-domain-names:
> > + items:
> > + - const: cx
> > + - const: mss
> > +
> > + required:
> > + - power-domains
> > + - power-domain-names
> > + - qcom,ext-regs
> > + - qcom,qaccept-regs
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + contains:
> > + enum:
> > + - qcom,q6v5-pil
> > + - qcom,msm8916-mss-pil
> > + - qcom,msm8974-mss-pil
> > + - qcom,msm8996-mss-pil
> > + - qcom,msm8998-mss-pil
> > + then:
> > + properties:
> > + resets:
> > + items:
> > + - description: MSS reset
> > + reset-names:
> > + items:
> > + - const: mss_restart
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + contains:
> > + enum:
> > + - qcom,ipq8074-wcss-pil
> > + - qcom,qcs404-wcss-pil
> > + then:
> > + properties:
> > + resets:
> > + items:
> > + - description: WCSS Always On restart
> > + - description: WCSS reset
> > + - description: WCSS Q6 reset
> > + reset-names:
> > + items:
> > + - const: wcss_aon_restart
> > + - const: wcss_reset
> > + - const: wcss_q6_reset
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + contains:
> > + enum:
> > + - qcom,sc7180-mss-pil
> > + - qcom,sc7280-mss-pil
> > + - qcom,sdm845-mss-pil
> > + then:
> > + properties:
> > + resets:
> > + items:
> > + - description: MSS restart
> > + - description: PDC reset
> > + reset-names:
> > + items:
> > + - const: mss_restart
> > + - const: pdc_reset
> > +
> > + - if:
> > + properties:
> > + compatible:
> > + contains:
> > + enum:
> > + - qcom,q6v5-pil
> > + - qcom,ipq8074-wcss-pil
> > + - qcom,qcs404-wcss-pil
> > + - qcom,msm8916-mss-pil
> > + - qcom,msm8974-mss-pil
> > + - qcom,msm8996-mss-pil
> > + - qcom,msm8998-mss-pil
> > + then:
> > + properties:
> > + qcom,qmp: false
> > + iommus: false
> > +
> > +examples:
> > + - |
> > + #include <dt-bindings/clock/qcom,rpmcc.h>
> > + #include <dt-bindings/interrupt-controller/irq.h>
> > + #include <dt-bindings/clock/qcom,gcc-msm8974.h>
> > + #include <dt-bindings/reset/qcom,gcc-msm8974.h>
> > + #include <dt-bindings/interrupt-controller/arm-gic.h>
> > + modem-rproc@fc880000 {
>
> Generic node name, so "remoteproc"
Will fix in v2
>
> > + compatible = "qcom,q6v5-pil";
> > + reg = <0xfc880000 0x100>,
> > + <0xfc820000 0x020>;
> > + reg-names = "qdsp6", "rmb";
> > +
> > + interrupts-extended = <&intc GIC_SPI 24 IRQ_TYPE_EDGE_RISING>,
> > + <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> > + <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> > + <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> > + <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
> > + interrupt-names = "wdog",
> > + "fatal",
> > + "ready",
> > + "handover",
> > + "stop-ack";
> > +
> > + clocks = <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
> > + <&gcc GCC_MSS_CFG_AHB_CLK>,
> > + <&gcc GCC_BOOT_ROM_AHB_CLK>,
> > + <&xo_board>;
> > + clock-names = "iface", "bus", "mem", "xo";
> > +
> > + qcom,halt-regs = <&tcsr_mutex_block 0x1180 0x1200 0x1280>;
>
> Does this pass the tests? Did you test the bindings?
Yes, both dtbs_check and dt_binding_check
>
> > +
> > + resets = <&gcc GCC_MSS_RESTART>;
> > + reset-names = "mss_restart";
> > +
> > + cx-supply = <&pm8841_s2>;
> > + mss-supply = <&pm8841_s3>;
> > + mx-supply = <&pm8841_s1>;
> > + pll-supply = <&pm8941_l12>;
> > +
> > + qcom,smem-states = <&modem_smp2p_out 0>;
> > + qcom,smem-state-names = "stop";
> > +
> > + mba {
> > + memory-region = <&mba_region>;
>
> Wrong indentation.
>
Will fix in v2
> > + };
> > +
> > + mpss {
> > + memory-region = <&mpss_region>;
> > + };
> > +
> > + smd-edge {
> > + interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
> > +
> > + qcom,ipc = <&apcs 8 12>;
> > + qcom,smd-edge = <0>;
> > +
> > + label = "modem";
> > + };
> > + };
>
>
> Best regards,
> Krzysztof
Thanks,
Sireesh Kodali
next prev parent reply other threads:[~2022-05-12 9:51 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-05-11 16:15 [PATCH 0/9] Add support for remoteprocs on the MSM8953 platform Sireesh Kodali
2022-05-11 16:15 ` [PATCH 1/9] remoteproc: qcom: pas: Add MSM8953 ADSP PIL support Sireesh Kodali
2022-05-11 16:49 ` Dmitry Baryshkov
2022-05-11 16:51 ` Dmitry Baryshkov
2022-05-12 10:39 ` Sireesh Kodali
2022-05-11 16:15 ` [PATCH 2/9] remoteproc: qcom: q6v5-mss: Add modem support on MSM8953 Sireesh Kodali
2022-05-11 16:54 ` Dmitry Baryshkov
2022-05-12 5:16 ` Sireesh Kodali
2022-05-12 10:38 ` Sireesh Kodali
2022-05-11 16:15 ` [PATCH 3/9] remoteproc: qcom: qcom_wcnss: Add support for pronto-v3 Sireesh Kodali
2022-05-11 16:15 ` [PATCH 4/9] dt-bindings: remoteproc: qcom: wcnss: Convert to YAML Sireesh Kodali
2022-05-11 17:15 ` Krzysztof Kozlowski
2022-05-12 6:50 ` Sireesh Kodali
2022-05-12 8:14 ` Krzysztof Kozlowski
2022-05-12 9:32 ` Sireesh Kodali
2022-05-12 11:02 ` Krzysztof Kozlowski
2022-05-12 13:42 ` Sireesh Kodali
2022-05-12 8:36 ` Krzysztof Kozlowski
2022-05-12 10:01 ` Sireesh Kodali
2022-05-12 13:49 ` Rob Herring
2022-12-01 13:22 ` Krzysztof Kozlowski
2022-12-01 16:17 ` Sireesh Kodali
2022-12-01 16:24 ` Krzysztof Kozlowski
2022-05-11 16:15 ` [PATCH 5/9] dt-bindings: remoteproc: qcom: wcnss: Add compatible for pronto v3 Sireesh Kodali
2022-05-11 16:15 ` [PATCH 6/9] dt-bindings: remoteproc: qcom: mss: Convert bindings to YAML Sireesh Kodali
2022-05-11 17:50 ` Krzysztof Kozlowski
2022-05-12 9:50 ` Sireesh Kodali [this message]
2022-05-12 13:49 ` Rob Herring
2022-05-11 16:16 ` [PATCH 7/9] dt-bindings: remoteproc: qcom: mss: Add MSS on MSM8953 Sireesh Kodali
2022-05-11 16:16 ` [PATCH 8/9] dt-bindings: remoteproc: qcom: adsp: Add ADSP " Sireesh Kodali
2022-05-11 16:16 ` [PATCH 9/9] arm64: dts: qcom: msm8953: Add remote processor nodes Sireesh Kodali
2022-05-11 17:55 ` Krzysztof Kozlowski
2022-05-12 9:19 ` Sireesh Kodali
2022-05-12 14:37 ` Krzysztof Kozlowski
2022-05-12 15:15 ` Sireesh Kodali
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CJXOUUY3IV5I.33259TNMB50JG@skynet-linux \
--to=sireeshkodali1@gmail.com \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=krzysztof.kozlowski@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-remoteproc@vger.kernel.org \
--cc=mathieu.poirier@linaro.org \
--cc=phone-devel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=~postmarketos/upstreaming@lists.sr.ht \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.