[U-Boot] [PATCH v3] usb: lpc32xx: add i2c DM support

[Marek Vasut <marex@denx.de>]

On 04/26/2017 01:57 PM, Sylvain Lemieux wrote:
> From: Liam Beguin <lbeguin@tycoint.com>
> 
> Add DM support for i2c functions.
> 
> Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
> Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>

Reviewed-by: Marek Vasut <marex@denx.de>

> ---
> Changes from v2 to v3:
> * Code clean-up to remove conditional compile else section (CONFIG_DM_I2C).
> * As suggested by Marek, added Simon Glass to the list of cc for the patch.
> 
> Changes from v1 to v2:
> * Do not request udevice on each single i2c write.
> 
> Note:
> * This patch is require as part of the DM support of the LPC32xx I2C driver.
>   All I2C drivers should be converted, to DM, by the end of June 2017.
> 
> * The USB driver is supporting the DM and non-DM API.
> 
> * Once the ustream LPC32xx boards (devkit3250 & work_92105) are migrated
>   to DM (I2C), the non-DM API support can be remove from this driver.
> 
>  drivers/usb/host/ohci-lpc32xx.c | 64 +++++++++++++++++++++++++++++------------
>  1 file changed, 46 insertions(+), 18 deletions(-)
> 
> diff --git a/drivers/usb/host/ohci-lpc32xx.c b/drivers/usb/host/ohci-lpc32xx.c
> index 9245126ed6..c0c423b994 100644
> --- a/drivers/usb/host/ohci-lpc32xx.c
> +++ b/drivers/usb/host/ohci-lpc32xx.c
> @@ -14,8 +14,10 @@
>  #include <asm/io.h>
>  #include <asm/arch/cpu.h>
>  #include <asm/arch/clk.h>
> +#include <asm/arch/i2c.h>
>  #include <usb.h>
>  #include <i2c.h>
> +#include <dm.h>
>  
>  /* OTG I2C controller module register structures */
>  struct otgi2c_regs {
> @@ -81,14 +83,20 @@ struct otg_regs {
>  static struct otg_regs *otg = (struct otg_regs *)USB_BASE;
>  static struct clk_pm_regs *clk_pwr = (struct clk_pm_regs *)CLK_PM_BASE;
>  
> -static int isp1301_set_value(int reg, u8 value)
> +static int isp1301_set_value(struct udevice *dev, int reg, u8 value)
>  {
> +#ifndef CONFIG_DM_I2C
>  	return i2c_write(ISP1301_I2C_ADDR, reg, 1, &value, 1);
> +#else
> +	return dm_i2c_write(dev, reg, &value, 1);
> +#endif
>  }
>  
> -static void isp1301_configure(void)
> +static void isp1301_configure(struct udevice *dev)
>  {
> +#ifndef CONFIG_DM_I2C
>  	i2c_set_bus_num(I2C_2);
> +#endif
>  
>  	/*
>  	 * LPC32XX only supports DAT_SE0 USB mode
> @@ -96,23 +104,23 @@ static void isp1301_configure(void)
>  	 */
>  
>  	/* Disable transparent UART mode first */
> -	isp1301_set_value(ISP1301_I2C_MODE_CONTROL_1_CLR, MC1_UART_EN);
> +	isp1301_set_value(dev, ISP1301_I2C_MODE_CONTROL_1_CLR, MC1_UART_EN);
>  
> -	isp1301_set_value(ISP1301_I2C_MODE_CONTROL_1_CLR, ~MC1_SPEED_REG);
> -	isp1301_set_value(ISP1301_I2C_MODE_CONTROL_1_SET, MC1_SPEED_REG);
> -	isp1301_set_value(ISP1301_I2C_MODE_CONTROL_2_CLR, ~0);
> -	isp1301_set_value(ISP1301_I2C_MODE_CONTROL_2_SET,
> +	isp1301_set_value(dev, ISP1301_I2C_MODE_CONTROL_1_CLR, ~MC1_SPEED_REG);
> +	isp1301_set_value(dev, ISP1301_I2C_MODE_CONTROL_1_SET, MC1_SPEED_REG);
> +	isp1301_set_value(dev, ISP1301_I2C_MODE_CONTROL_2_CLR, ~0);
> +	isp1301_set_value(dev, ISP1301_I2C_MODE_CONTROL_2_SET,
>  			  MC2_BI_DI | MC2_PSW_EN | MC2_SPD_SUSP_CTRL);
>  
> -	isp1301_set_value(ISP1301_I2C_OTG_CONTROL_1_CLR, ~0);
> -	isp1301_set_value(ISP1301_I2C_MODE_CONTROL_1_SET, MC1_DAT_SE0);
> -	isp1301_set_value(ISP1301_I2C_OTG_CONTROL_1_SET,
> +	isp1301_set_value(dev, ISP1301_I2C_OTG_CONTROL_1_CLR, ~0);
> +	isp1301_set_value(dev, ISP1301_I2C_MODE_CONTROL_1_SET, MC1_DAT_SE0);
> +	isp1301_set_value(dev, ISP1301_I2C_OTG_CONTROL_1_SET,
>  			  OTG1_DM_PULLDOWN | OTG1_DP_PULLDOWN);
> -	isp1301_set_value(ISP1301_I2C_OTG_CONTROL_1_CLR,
> +	isp1301_set_value(dev, ISP1301_I2C_OTG_CONTROL_1_CLR,
>  			  OTG1_DM_PULLUP | OTG1_DP_PULLUP);
> -	isp1301_set_value(ISP1301_I2C_INTERRUPT_LATCH_CLR, ~0);
> -	isp1301_set_value(ISP1301_I2C_INTERRUPT_FALLING_CLR, ~0);
> -	isp1301_set_value(ISP1301_I2C_INTERRUPT_RISING_CLR, ~0);
> +	isp1301_set_value(dev, ISP1301_I2C_INTERRUPT_LATCH_CLR, ~0);
> +	isp1301_set_value(dev, ISP1301_I2C_INTERRUPT_FALLING_CLR, ~0);
> +	isp1301_set_value(dev, ISP1301_I2C_INTERRUPT_RISING_CLR, ~0);
>  
>  	/* Enable usb_need_clk clock after transceiver is initialized */
>  	setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_USBDVND_EN);
> @@ -149,6 +157,15 @@ static int usbpll_setup(void)
>  int usb_cpu_init(void)
>  {
>  	u32 ret;
> +	struct udevice *dev = NULL;
> +
> +#ifdef CONFIG_DM_I2C
> +	ret = i2c_get_chip_for_busnum(I2C_2, ISP1301_I2C_ADDR, 1, &dev);
> +	if (ret) {
> +		debug("%s: No bus %d\n", __func__, I2C_2);
> +		return ret;
> +	}
> +#endif
>  
>  	/*
>  	 * USB pins routing setup is done by "lpc32xx_usb_init()" and should
> @@ -167,7 +184,7 @@ int usb_cpu_init(void)
>  		return ret;
>  
>  	/* Configure ISP1301 */
> -	isp1301_configure();
> +	isp1301_configure(dev);
>  
>  	/* setup USB clocks and PLL */
>  	ret = usbpll_setup();
> @@ -188,21 +205,32 @@ int usb_cpu_init(void)
>  		return ret;
>  
>  	setbits_le32(&otg->otg_sts_ctrl, OTG_HOST_EN);
> -	isp1301_set_value(ISP1301_I2C_OTG_CONTROL_1_SET, OTG1_VBUS_DRV);
> +	isp1301_set_value(dev, ISP1301_I2C_OTG_CONTROL_1_SET, OTG1_VBUS_DRV);
>  
>  	return 0;
>  }
>  
>  int usb_cpu_stop(void)
>  {
> +	struct udevice *dev = NULL;
> +	int ret = 0;
> +
> +#ifdef CONFIG_DM_I2C
> +	ret = i2c_get_chip_for_busnum(I2C_2, ISP1301_I2C_ADDR, 1, &dev);
> +	if (ret) {
> +		debug("%s: No bus %d\n", __func__, I2C_2);
> +		return ret;
> +	}
> +#endif
> +
>  	/* vbus off */
> -	isp1301_set_value(ISP1301_I2C_OTG_CONTROL_1_SET, OTG1_VBUS_DRV);
> +	isp1301_set_value(dev, ISP1301_I2C_OTG_CONTROL_1_SET, OTG1_VBUS_DRV);
>  
>  	clrbits_le32(&otg->otg_sts_ctrl, OTG_HOST_EN);
>  
>  	clrbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_HCLK_EN);
>  
> -	return 0;
> +	return ret;
>  }
>  
>  int usb_cpu_init_fail(void)
> 


-- 
Best regards,
Marek Vasut