From mboxrd@z Thu Jan 1 00:00:00 1970 From: Heiko Schocher Date: Fri, 17 Sep 2010 13:10:29 +0200 Subject: [U-Boot] [PATCH 02/26 v2][NEXT] ARM: cp15: setup mmu and enable dcache In-Reply-To: <1284721853-8298-2-git-send-email-hs@denx.de> References: <4C62E8C3.8050006@denx.de> <1284721853-8298-1-git-send-email-hs@denx.de> <1284721853-8298-2-git-send-email-hs@denx.de> Message-ID: <1284721853-8298-3-git-send-email-hs@denx.de> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de This has been tested on at91sam9263 and STN8815. Again, I didn't check if it has bad effects on non-arm926 cores. Initially I had a "done" bit to only set up page tables at the beginning. However, since the aligmnent requirement was for the whole object file, this extra integer tool 16kB in BSS, so I chose to remove it. Also, note not all boards use PHYS_SDRAM, but it looks like it's the most used name (more than CONFIG_SYS_DRAM_BASE for example). Portions of this work were supported by funding from the CE Linux Forum. Signed-off-by: Alessandro Rubini Signed-off-by: Heiko Schocher --- arch/arm/lib/cache-cp15.c | 51 +++++++++++++++++++++++++++++++++++++++++++++ 1 files changed, 51 insertions(+), 0 deletions(-) diff --git a/arch/arm/lib/cache-cp15.c b/arch/arm/lib/cache-cp15.c index 62ed54f..b2811f3 100644 --- a/arch/arm/lib/cache-cp15.c +++ b/arch/arm/lib/cache-cp15.c @@ -25,6 +25,15 @@ #include #if !(defined(CONFIG_SYS_NO_ICACHE) && defined(CONFIG_SYS_NO_DCACHE)) + +#if defined(CONFIG_SYS_ARM_CACHE_WRITETHROUGH) +#define CACHE_SETUP 0x1a +#else +#define CACHE_SETUP 0x1e +#endif + +DECLARE_GLOBAL_DATA_PTR; + static void cp_delay (void) { volatile int i; @@ -32,6 +41,40 @@ static void cp_delay (void) /* copro seems to need some delay between reading and writing */ for (i = 0; i < 100; i++) nop(); + asm volatile("" : : : "memory"); +} + +/* to activate the MMU we need to set up virtual memory: use 1M areas in bss */ +static inline void mmu_setup(void) +{ + static u32 __attribute__((aligned(16384))) page_table[4096]; + bd_t *bd = gd->bd; + int i, j; + u32 reg; + + /* Set up an identity-mapping for all 4GB, rw for everyone */ + for (i = 0; i < 4096; i++) + page_table[i] = i << 20 | (3 << 10) | 0x12; + /* Then, enable cacheable and bufferable for RAM only */ + for (j = 0; j < CONFIG_NR_DRAM_BANKS; j++) { + for (i = bd->bi_dram[j].start >> 20; + i < (bd->bi_dram[j].start + bd->bi_dram[j].size) >> 20; + i++) { + page_table[i] = i << 20 | (3 << 10) | CACHE_SETUP; + } + } + + /* Copy the page table address to cp15 */ + asm volatile("mcr p15, 0, %0, c2, c0, 0" + : : "r" (page_table) : "memory"); + /* Set the access control to all-supervisor */ + asm volatile("mcr p15, 0, %0, c3, c0, 0" + : : "r" (~0)); + /* and enable the mmu */ + reg = get_cr(); /* get control reg. */ + cp_delay(); + set_cr(reg | CR_M); + } /* cache_bit must be either CR_I or CR_C */ @@ -39,6 +82,9 @@ static void cache_enable(uint32_t cache_bit) { uint32_t reg; + /* The data cache is not active unless the mmu is enabled too */ + if (cache_bit == CR_C) + mmu_setup(); reg = get_cr(); /* get control reg. */ cp_delay(); set_cr(reg | cache_bit); @@ -49,6 +95,11 @@ static void cache_disable(uint32_t cache_bit) { uint32_t reg; + if (cache_bit == CR_C) { + /* if disabling data cache, disable mmu too */ + cache_bit |= CR_M; + flush_cache(0, ~0); + } reg = get_cr(); cp_delay(); set_cr(reg & ~cache_bit); -- 1.6.2.5