i.MX unnecessary ifdef removal

i.MX unnecessary ifdef removal

[Sascha Hauer]

The following patches remove several unnecessary ifdefs in board
files.

Sascha

The following changes since commit 376e9c5848abef8c72c09bd89f2f7ee128caa104:

  ARM: mxs: add initial pm support (2011-01-26 08:30:49 +0100)

are available in the git repository at:
  none ..BRANCH.NOT.VERIFIED..

Sascha Hauer (13):
      ARM i.MX35 pcm043: remove unnecessary CONFIG_I2C ifdefs
      ARM i.MX35 pcm043: put usbh1 outside CONFIG_USB_ULPI
      ARM i.MX31 mx31ads: remove unnecessary CONFIG_I2C ifdefs
      ARM i.MX31 mx31ads: remove unnecessary CONFIG_SERIAL_IMX ifdefs
      ARM i.MX31 mx31ads: remove unnecessary CONFIG_SERIAL_8250 ifdefs
      ARM i.MX27 pca100: remove unnecessary CONFIG_SPI_IMX ifdefs
      ARM i.MX27 eukrea mbimx27: remove unnecessary CONFIG_SPI_IMX ifdefs
      ARM i.MX31 pcm037 eet: remove unnecessary CONFIG_SPI_IMX ifdefs
      ARM i.MX51 mx51 3ds: remove unnecessary CONFIG_SERIAL_IMX ifdefs
      ARM i.MX51 mx51 babbage: remove unnecessary CONFIG_SERIAL_IMX ifdefs
      ARM i.MX51 mx51 babbage: remove unnecessary CONFIG_KEYBOARD_IMX ifdefs
      ARM i.MX51 cpuimx51: remove unnecessary CONFIG_SERIAL_8250 ifdefs
      ARM i.MX51 efikamx: remove unnecessary CONFIG_SERIAL_IMX ifdefs

 arch/arm/mach-imx/eukrea_mbimx27-baseboard.c |    2 -
 arch/arm/mach-imx/mach-pca100.c              |    4 ---
 arch/arm/mach-mx3/mach-mx31ads.c             |   21 +-------------------
 arch/arm/mach-mx3/mach-pcm037_eet.c          |    2 -
 arch/arm/mach-mx3/mach-pcm043.c              |   10 ++------
 arch/arm/mach-mx5/board-cpuimx51.c           |    4 ---
 arch/arm/mach-mx5/board-mx51_3ds.c           |   27 ++++---------------------
 arch/arm/mach-mx5/board-mx51_babbage.c       |   19 ++++-------------
 arch/arm/mach-mx5/board-mx51_efikamx.c       |   17 ++-------------
 9 files changed, 17 insertions(+), 89 deletions(-)

[PATCH 01/13] ARM i.MX35 pcm043: remove unnecessary CONFIG_I2C ifdefs

[Sascha Hauer]

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-mx3/mach-pcm043.c |    4 ----
 1 files changed, 0 insertions(+), 4 deletions(-)

diff --git a/arch/arm/mach-mx3/mach-pcm043.c b/arch/arm/mach-mx3/mach-pcm043.c
index bcf83fc..a27022d 100644
--- a/arch/arm/mach-mx3/mach-pcm043.c
+++ b/arch/arm/mach-mx3/mach-pcm043.c
@@ -115,7 +115,6 @@ static const struct imxuart_platform_data uart_pdata __initconst = {
 	.flags = IMXUART_HAVE_RTSCTS,
 };
 
-#if defined CONFIG_I2C_IMX || defined CONFIG_I2C_IMX_MODULE
 static const struct imxi2c_platform_data pcm043_i2c0_data __initconst = {
 	.bitrate = 50000,
 };
@@ -134,7 +133,6 @@ static struct i2c_board_info pcm043_i2c_devices[] = {
 		I2C_BOARD_INFO("pcf8563", 0x51),
 	}
 };
-#endif
 
 static struct platform_device *devices[] __initdata = {
 	&pcm043_flash,
@@ -369,12 +367,10 @@ static void __init mxc_board_init(void)
 
 	imx35_add_imx_uart1(&uart_pdata);
 
-#if defined CONFIG_I2C_IMX || defined CONFIG_I2C_IMX_MODULE
 	i2c_register_board_info(0, pcm043_i2c_devices,
 			ARRAY_SIZE(pcm043_i2c_devices));
 
 	imx35_add_imx_i2c0(&pcm043_i2c0_data);
-#endif
 
 	mxc_register_device(&mx3_ipu, &mx3_ipu_data);
 	mxc_register_device(&mx3_fb, &mx3fb_pdata);
-- 
1.7.2.3

[PATCH 02/13] ARM i.MX35 pcm043: put usbh1 outside CONFIG_USB_ULPI

[Sascha Hauer]

The usbh1 port of the pcm043 does not use ulpi, so put it outside
the corresponding ifdefs.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-mx3/mach-pcm043.c |    6 +++---
 1 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-mx3/mach-pcm043.c b/arch/arm/mach-mx3/mach-pcm043.c
index a27022d..a515290 100644
--- a/arch/arm/mach-mx3/mach-pcm043.c
+++ b/arch/arm/mach-mx3/mach-pcm043.c
@@ -310,13 +310,13 @@ static struct mxc_usbh_platform_data otg_pdata __initdata = {
 	.portsc	= MXC_EHCI_MODE_UTMI,
 	.flags	= MXC_EHCI_INTERFACE_DIFF_UNI,
 };
+#endif
 
 static const struct mxc_usbh_platform_data usbh1_pdata __initconst = {
 	.portsc	= MXC_EHCI_MODE_SERIAL,
 	.flags	= MXC_EHCI_INTERFACE_SINGLE_UNI | MXC_EHCI_INTERNAL_PHY |
 		  MXC_EHCI_IPPUE_DOWN,
 };
-#endif
 
 static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
 	.operating_mode = FSL_USB2_DR_DEVICE,
@@ -382,9 +382,9 @@ static void __init mxc_board_init(void)
 
 		imx35_add_mxc_ehci_otg(&otg_pdata);
 	}
-
-	imx35_add_mxc_ehci_hs(&usbh1_pdata);
 #endif
+	imx35_add_mxc_ehci_hs(&usbh1_pdata);
+
 	if (!otg_mode_host)
 		imx35_add_fsl_usb2_udc(&otg_device_pdata);
 
-- 
1.7.2.3

[PATCH 03/13] ARM i.MX31 mx31ads: remove unnecessary CONFIG_I2C ifdefs

[Sascha Hauer]

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-mx3/mach-mx31ads.c |    6 ------
 1 files changed, 0 insertions(+), 6 deletions(-)

diff --git a/arch/arm/mach-mx3/mach-mx31ads.c b/arch/arm/mach-mx3/mach-mx31ads.c
index 88b97d6..f9a7109 100644
--- a/arch/arm/mach-mx3/mach-mx31ads.c
+++ b/arch/arm/mach-mx3/mach-mx31ads.c
@@ -476,7 +476,6 @@ static struct wm8350_platform_data __initdata mx31_wm8350_pdata = {
 };
 #endif
 
-#if defined(CONFIG_I2C_IMX) || defined(CONFIG_I2C_IMX_MODULE)
 static struct i2c_board_info __initdata mx31ads_i2c1_devices[] = {
 #ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
 	{
@@ -497,11 +496,6 @@ static void mxc_init_i2c(void)
 
 	imx31_add_imx_i2c1(NULL);
 }
-#else
-static void mxc_init_i2c(void)
-{
-}
-#endif
 
 static unsigned int ssi_pins[] = {
 	MX31_PIN_SFS5__SFS5,
-- 
1.7.2.3

[PATCH 04/13] ARM i.MX31 mx31ads: remove unnecessary CONFIG_SERIAL_IMX ifdefs

[Sascha Hauer]

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-mx3/mach-mx31ads.c |    6 ------
 1 files changed, 0 insertions(+), 6 deletions(-)

diff --git a/arch/arm/mach-mx3/mach-mx31ads.c b/arch/arm/mach-mx3/mach-mx31ads.c
index f9a7109..1a83dc5 100644
--- a/arch/arm/mach-mx3/mach-mx31ads.c
+++ b/arch/arm/mach-mx3/mach-mx31ads.c
@@ -117,7 +117,6 @@ static inline int mxc_init_extuart(void)
 }
 #endif
 
-#if defined(CONFIG_SERIAL_IMX) || defined(CONFIG_SERIAL_IMX_MODULE)
 static const struct imxuart_platform_data uart_pdata __initconst = {
 	.flags = IMXUART_HAVE_RTSCTS,
 };
@@ -134,11 +133,6 @@ static inline void mxc_init_imx_uart(void)
 	mxc_iomux_setup_multiple_pins(uart_pins, ARRAY_SIZE(uart_pins), "uart-0");
 	imx31_add_imx_uart0(&uart_pdata);
 }
-#else /* !SERIAL_IMX */
-static inline void mxc_init_imx_uart(void)
-{
-}
-#endif /* !SERIAL_IMX */
 
 static void mx31ads_expio_irq_handler(u32 irq, struct irq_desc *desc)
 {
-- 
1.7.2.3

[PATCH 05/13] ARM i.MX31 mx31ads: remove unnecessary CONFIG_SERIAL_8250 ifdefs

[Sascha Hauer]

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-mx3/mach-mx31ads.c |    9 +--------
 1 files changed, 1 insertions(+), 8 deletions(-)

diff --git a/arch/arm/mach-mx3/mach-mx31ads.c b/arch/arm/mach-mx3/mach-mx31ads.c
index 1a83dc5..e40eb6e 100644
--- a/arch/arm/mach-mx3/mach-mx31ads.c
+++ b/arch/arm/mach-mx3/mach-mx31ads.c
@@ -73,8 +73,7 @@
  * This file contains the board-specific initialization routines.
  */
 
-#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
-/*!
+/*
  * The serial port definition structure.
  */
 static struct plat_serial8250_port serial_platform_data[] = {
@@ -110,12 +109,6 @@ static int __init mxc_init_extuart(void)
 {
 	return platform_device_register(&serial_device);
 }
-#else
-static inline int mxc_init_extuart(void)
-{
-	return 0;
-}
-#endif
 
 static const struct imxuart_platform_data uart_pdata __initconst = {
 	.flags = IMXUART_HAVE_RTSCTS,
-- 
1.7.2.3

[PATCH 06/13] ARM i.MX27 pca100: remove unnecessary CONFIG_SPI_IMX ifdefs

[Sascha Hauer]

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-imx/mach-pca100.c |    4 ----
 1 files changed, 0 insertions(+), 4 deletions(-)

diff --git a/arch/arm/mach-imx/mach-pca100.c b/arch/arm/mach-imx/mach-pca100.c
index cccc0a0..faa4e04 100644
--- a/arch/arm/mach-imx/mach-pca100.c
+++ b/arch/arm/mach-imx/mach-pca100.c
@@ -187,7 +187,6 @@ static struct i2c_board_info pca100_i2c_devices[] = {
 	}
 };
 
-#if defined(CONFIG_SPI_IMX) || defined(CONFIG_SPI_IMX_MODULE)
 static struct spi_eeprom at25320 = {
 	.name		= "at25320an",
 	.byte_len	= 4096,
@@ -211,7 +210,6 @@ static const struct spi_imx_master pca100_spi0_data __initconst = {
 	.chipselect	= pca100_spi_cs,
 	.num_chipselect = ARRAY_SIZE(pca100_spi_cs),
 };
-#endif
 
 static void pca100_ac97_warm_reset(struct snd_ac97 *ac97)
 {
@@ -389,13 +387,11 @@ static void __init pca100_init(void)
 
 	imx27_add_imx_i2c(1, &pca100_i2c1_data);
 
-#if defined(CONFIG_SPI_IMX) || defined(CONFIG_SPI_IMX_MODULE)
 	mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_IN);
 	mxc_gpio_mode(GPIO_PORTD | 27 | GPIO_GPIO | GPIO_IN);
 	spi_register_board_info(pca100_spi_board_info,
 				ARRAY_SIZE(pca100_spi_board_info));
 	imx27_add_spi_imx0(&pca100_spi0_data);
-#endif
 
 	gpio_request(OTG_PHY_CS_GPIO, "usb-otg-cs");
 	gpio_direction_output(OTG_PHY_CS_GPIO, 1);
-- 
1.7.2.3

[PATCH 07/13] ARM i.MX27 eukrea mbimx27: remove unnecessary CONFIG_SPI_IMX ifdefs

[Sascha Hauer]

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-imx/eukrea_mbimx27-baseboard.c |    2 --
 1 files changed, 0 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-imx/eukrea_mbimx27-baseboard.c b/arch/arm/mach-imx/eukrea_mbimx27-baseboard.c
index 275c858..b6d68cf 100644
--- a/arch/arm/mach-imx/eukrea_mbimx27-baseboard.c
+++ b/arch/arm/mach-imx/eukrea_mbimx27-baseboard.c
@@ -357,13 +357,11 @@ void __init eukrea_mbimx27_baseboard_init(void)
 	ads7846_dev_init();
 #endif
 
-#if defined(CONFIG_SPI_IMX) || defined(CONFIG_SPI_IMX_MODULE)
 	/* SPI_CS0 init */
 	mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_OUT);
 	imx27_add_spi_imx0(&eukrea_mbimx27_spi0_data);
 	spi_register_board_info(eukrea_mbimx27_spi_board_info,
 			ARRAY_SIZE(eukrea_mbimx27_spi_board_info));
-#endif
 
 	/* Leds configuration */
 	mxc_gpio_mode(GPIO_PORTF | 16 | GPIO_GPIO | GPIO_OUT);
-- 
1.7.2.3

[PATCH 08/13] ARM i.MX31 pcm037 eet: remove unnecessary CONFIG_SPI_IMX ifdefs

[Sascha Hauer]

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-mx3/mach-pcm037_eet.c |    2 --
 1 files changed, 0 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-mx3/mach-pcm037_eet.c b/arch/arm/mach-mx3/mach-pcm037_eet.c
index fda5654..df6fb07 100644
--- a/arch/arm/mach-mx3/mach-pcm037_eet.c
+++ b/arch/arm/mach-mx3/mach-pcm037_eet.c
@@ -180,9 +180,7 @@ static int __init eet_init_devices(void)
 
 	/* SPI */
 	spi_register_board_info(pcm037_spi_dev, ARRAY_SIZE(pcm037_spi_dev));
-#if defined(CONFIG_SPI_IMX) || defined(CONFIG_SPI_IMX_MODULE)
 	imx31_add_spi_imx0(&pcm037_spi1_pdata);
-#endif
 
 	platform_device_register(&pcm037_gpio_keys_device);
 
-- 
1.7.2.3

[PATCH 09/13] ARM i.MX51 mx51 3ds: remove unnecessary CONFIG_SERIAL_IMX ifdefs

[Sascha Hauer]

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-mx5/board-mx51_3ds.c |   14 ++++----------
 1 files changed, 4 insertions(+), 10 deletions(-)

diff --git a/arch/arm/mach-mx5/board-mx51_3ds.c b/arch/arm/mach-mx5/board-mx51_3ds.c
index 8a0619b..feb2800 100644
--- a/arch/arm/mach-mx5/board-mx51_3ds.c
+++ b/arch/arm/mach-mx5/board-mx51_3ds.c
@@ -71,22 +71,13 @@ static iomux_v3_cfg_t mx51_3ds_pads[] = {
 };
 
 /* Serial ports */
-#if defined(CONFIG_SERIAL_IMX) || defined(CONFIG_SERIAL_IMX_MODULE)
 static const struct imxuart_platform_data uart_pdata __initconst = {
 	.flags = IMXUART_HAVE_RTSCTS,
 };
 
 static inline void mxc_init_imx_uart(void)
 {
-	imx51_add_imx_uart(0, &uart_pdata);
-	imx51_add_imx_uart(1, &uart_pdata);
-	imx51_add_imx_uart(2, &uart_pdata);
-}
-#else /* !SERIAL_IMX */
-static inline void mxc_init_imx_uart(void)
-{
 }
-#endif /* SERIAL_IMX */
 
 #if defined(CONFIG_KEYBOARD_IMX) || defined(CONFIG_KEYBOARD_IMX_MODULE)
 static int mx51_3ds_board_keymap[] = {
@@ -161,7 +152,10 @@ static void __init mxc_board_init(void)
 {
 	mxc_iomux_v3_setup_multiple_pads(mx51_3ds_pads,
 					ARRAY_SIZE(mx51_3ds_pads));
-	mxc_init_imx_uart();
+
+	imx51_add_imx_uart(0, &uart_pdata);
+	imx51_add_imx_uart(1, &uart_pdata);
+	imx51_add_imx_uart(2, &uart_pdata);
 
 	imx51_add_ecspi(1, &mx51_3ds_ecspi2_pdata);
 	spi_register_board_info(mx51_3ds_spi_nor_device,
-- 
1.7.2.3

[PATCH 10/13] ARM i.MX51 mx51 babbage: remove unnecessary CONFIG_SERIAL_IMX ifdefs

[Sascha Hauer]

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-mx5/board-mx51_babbage.c |   19 +++++--------------
 1 files changed, 5 insertions(+), 14 deletions(-)

diff --git a/arch/arm/mach-mx5/board-mx51_babbage.c b/arch/arm/mach-mx5/board-mx51_babbage.c
index 1d231e8..d9d402e 100644
--- a/arch/arm/mach-mx5/board-mx51_babbage.c
+++ b/arch/arm/mach-mx5/board-mx51_babbage.c
@@ -161,23 +161,10 @@ static iomux_v3_cfg_t mx51babbage_pads[] = {
 };
 
 /* Serial ports */
-#if defined(CONFIG_SERIAL_IMX) || defined(CONFIG_SERIAL_IMX_MODULE)
 static const struct imxuart_platform_data uart_pdata __initconst = {
 	.flags = IMXUART_HAVE_RTSCTS,
 };
 
-static inline void mxc_init_imx_uart(void)
-{
-	imx51_add_imx_uart(0, &uart_pdata);
-	imx51_add_imx_uart(1, &uart_pdata);
-	imx51_add_imx_uart(2, &uart_pdata);
-}
-#else /* !SERIAL_IMX */
-static inline void mxc_init_imx_uart(void)
-{
-}
-#endif /* SERIAL_IMX */
-
 static const struct imxi2c_platform_data babbage_i2c_data __initconst = {
 	.bitrate = 100000,
 };
@@ -360,7 +347,11 @@ static void __init mxc_board_init(void)
 #endif
 	mxc_iomux_v3_setup_multiple_pads(mx51babbage_pads,
 					ARRAY_SIZE(mx51babbage_pads));
-	mxc_init_imx_uart();
+
+	imx51_add_imx_uart(0, &uart_pdata);
+	imx51_add_imx_uart(1, &uart_pdata);
+	imx51_add_imx_uart(2, &uart_pdata);
+
 	babbage_fec_reset();
 	imx51_add_fec(NULL);
 
-- 
1.7.2.3

[PATCH 11/13] ARM i.MX51 mx51 babbage: remove unnecessary CONFIG_KEYBOARD_IMX ifdefs

[Sascha Hauer]

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-mx5/board-mx51_3ds.c |   13 +------------
 1 files changed, 1 insertions(+), 12 deletions(-)

diff --git a/arch/arm/mach-mx5/board-mx51_3ds.c b/arch/arm/mach-mx5/board-mx51_3ds.c
index feb2800..58a2574 100644
--- a/arch/arm/mach-mx5/board-mx51_3ds.c
+++ b/arch/arm/mach-mx5/board-mx51_3ds.c
@@ -79,7 +79,6 @@ static inline void mxc_init_imx_uart(void)
 {
 }
 
-#if defined(CONFIG_KEYBOARD_IMX) || defined(CONFIG_KEYBOARD_IMX_MODULE)
 static int mx51_3ds_board_keymap[] = {
 	KEY(0, 0, KEY_1),
 	KEY(0, 1, KEY_2),
@@ -115,16 +114,6 @@ static const struct matrix_keymap_data mx51_3ds_map_data __initconst = {
 	.keymap_size	= ARRAY_SIZE(mx51_3ds_board_keymap),
 };
 
-static void mxc_init_keypad(void)
-{
-	imx51_add_imx_keypad(&mx51_3ds_map_data);
-}
-#else
-static inline void mxc_init_keypad(void)
-{
-}
-#endif
-
 static int mx51_3ds_spi2_cs[] = {
 	MXC_SPI_CS(0),
 	MX51_3DS_ECSPI2_CS,
@@ -166,7 +155,7 @@ static void __init mxc_board_init(void)
 				    "devices on the board are unusable.\n");
 
 	imx51_add_sdhci_esdhc_imx(0, NULL);
-	mxc_init_keypad();
+	imx51_add_imx_keypad(&mx51_3ds_map_data);
 	imx51_add_imx2_wdt(0, NULL);
 }
 
-- 
1.7.2.3

[PATCH 12/13] ARM i.MX51 cpuimx51: remove unnecessary CONFIG_SERIAL_8250 ifdefs

[Sascha Hauer]

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-mx5/board-cpuimx51.c |    4 ----
 1 files changed, 0 insertions(+), 4 deletions(-)

diff --git a/arch/arm/mach-mx5/board-cpuimx51.c b/arch/arm/mach-mx5/board-cpuimx51.c
index f8652ef..f576a97 100644
--- a/arch/arm/mach-mx5/board-cpuimx51.c
+++ b/arch/arm/mach-mx5/board-cpuimx51.c
@@ -60,7 +60,6 @@
 #define	MX51_USB_PLL_DIV_19_2_MHZ	0x01
 #define	MX51_USB_PLL_DIV_24_MHZ		0x02
 
-#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
 static struct plat_serial8250_port serial_platform_data[] = {
 	{
 		.mapbase = (unsigned long)(MX51_CS1_BASE_ADDR + 0x400000),
@@ -105,12 +104,9 @@ static struct platform_device serial_device = {
 		.platform_data = serial_platform_data,
 	},
 };
-#endif
 
 static struct platform_device *devices[] __initdata = {
-#if defined(CONFIG_SERIAL_8250) || defined(CONFIG_SERIAL_8250_MODULE)
 	&serial_device,
-#endif
 };
 
 static iomux_v3_cfg_t eukrea_cpuimx51_pads[] = {
-- 
1.7.2.3

[PATCH 13/13] ARM i.MX51 efikamx: remove unnecessary CONFIG_SERIAL_IMX ifdefs

[Sascha Hauer]

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-mx5/board-mx51_efikamx.c |   17 +++--------------
 1 files changed, 3 insertions(+), 14 deletions(-)

diff --git a/arch/arm/mach-mx5/board-mx51_efikamx.c b/arch/arm/mach-mx5/board-mx51_efikamx.c
index b7946f8..e237040 100644
--- a/arch/arm/mach-mx5/board-mx51_efikamx.c
+++ b/arch/arm/mach-mx5/board-mx51_efikamx.c
@@ -121,23 +121,10 @@ static iomux_v3_cfg_t mx51efikamx_pads[] = {
 };
 
 /* Serial ports */
-#if defined(CONFIG_SERIAL_IMX) || defined(CONFIG_SERIAL_IMX_MODULE)
 static const struct imxuart_platform_data uart_pdata = {
 	.flags = IMXUART_HAVE_RTSCTS,
 };
 
-static inline void mxc_init_imx_uart(void)
-{
-	imx51_add_imx_uart(0, &uart_pdata);
-	imx51_add_imx_uart(1, &uart_pdata);
-	imx51_add_imx_uart(2, &uart_pdata);
-}
-#else /* !SERIAL_IMX */
-static inline void mxc_init_imx_uart(void)
-{
-}
-#endif /* SERIAL_IMX */
-
 /* This function is board specific as the bit mask for the plldiv will also
  * be different for other Freescale SoCs, thus a common bitmask is not
  * possible and cannot get place in /plat-mxc/ehci.c.
@@ -320,7 +307,9 @@ static void __init mxc_board_init(void)
 					ARRAY_SIZE(mx51efikamx_pads));
 	mx51_efikamx_board_id();
 	mxc_register_device(&mxc_usbdr_host_device, &dr_utmi_config);
-	mxc_init_imx_uart();
+	imx51_add_imx_uart(0, &uart_pdata);
+	imx51_add_imx_uart(1, &uart_pdata);
+	imx51_add_imx_uart(2, &uart_pdata);
 	imx51_add_sdhci_esdhc_imx(0, NULL);
 
 	/* on < 1.2 boards both SD controllers are used */
-- 
1.7.2.3

[PATCH 11/13] ARM i.MX51 mx51 babbage: remove unnecessary CONFIG_KEYBOARD_IMX ifdefs

[Fabio Estevam]

Hi Sascha,

On Thu, Jan 27, 2011 at 11:00 AM, Sascha Hauer <s.hauer@pengutronix.de> wrote:
> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
> ---
> ?arch/arm/mach-mx5/board-mx51_3ds.c | ? 13 +------------
> ?1 files changed, 1 insertions(+), 12 deletions(-)
>
> diff --git a/arch/arm/mach-mx5/board-mx51_3ds.c b/arch/arm/mach-mx5/board-mx51_3ds.c
> index feb2800..58a2574 100644
> --- a/arch/arm/mach-mx5/board-mx51_3ds.c
> +++ b/arch/arm/mach-mx5/board-mx51_3ds.c

In the subject field you should put MX51_3ds instead of Babbage.

Regards,

Fabio Estevam

[PATCH 09/13] ARM i.MX51 mx51 3ds: remove unnecessary CONFIG_SERIAL_IMX ifdefs

[Sergei Shtylyov]

Hello.

On 27-01-2011 16:00, Sascha Hauer wrote:

> Signed-off-by: Sascha Hauer<s.hauer@pengutronix.de>
> ---
>   arch/arm/mach-mx5/board-mx51_3ds.c |   14 ++++----------
>   1 files changed, 4 insertions(+), 10 deletions(-)

> diff --git a/arch/arm/mach-mx5/board-mx51_3ds.c b/arch/arm/mach-mx5/board-mx51_3ds.c
> index 8a0619b..feb2800 100644
> --- a/arch/arm/mach-mx5/board-mx51_3ds.c
> +++ b/arch/arm/mach-mx5/board-mx51_3ds.c
> @@ -71,22 +71,13 @@ static iomux_v3_cfg_t mx51_3ds_pads[] = {
>   };
>
>   /* Serial ports */
> -#if defined(CONFIG_SERIAL_IMX) || defined(CONFIG_SERIAL_IMX_MODULE)
>   static const struct imxuart_platform_data uart_pdata __initconst = {
>   	.flags = IMXUART_HAVE_RTSCTS,
>   };
>
>   static inline void mxc_init_imx_uart(void)
>   {
> -	imx51_add_imx_uart(0, &uart_pdata);
> -	imx51_add_imx_uart(1, &uart_pdata);
> -	imx51_add_imx_uart(2, &uart_pdata);
> -}
> -#else /* !SERIAL_IMX */
> -static inline void mxc_init_imx_uart(void)
> -{
>   }

    Why then leave the empty function?

> -#endif /* SERIAL_IMX */
>
>   #if defined(CONFIG_KEYBOARD_IMX) || defined(CONFIG_KEYBOARD_IMX_MODULE)
>   static int mx51_3ds_board_keymap[] = {
> @@ -161,7 +152,10 @@ static void __init mxc_board_init(void)
>   {
>   	mxc_iomux_v3_setup_multiple_pads(mx51_3ds_pads,
>   					ARRAY_SIZE(mx51_3ds_pads));
> -	mxc_init_imx_uart();
> +
> +	imx51_add_imx_uart(0, &uart_pdata);
> +	imx51_add_imx_uart(1, &uart_pdata);
> +	imx51_add_imx_uart(2, &uart_pdata);
>
>   	imx51_add_ecspi(1,&mx51_3ds_ecspi2_pdata);
>   	spi_register_board_info(mx51_3ds_spi_nor_device,

WBR, Sergei

[PATCH 13/13] ARM i.MX51 efikamx: remove unnecessary CONFIG_SERIAL_IMX ifdefs

[Arnaud Patard (Rtp)]

Sascha Hauer <s.hauer@pengutronix.de> writes:

Hi,

> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
> ---
>  arch/arm/mach-mx5/board-mx51_efikamx.c |   17 +++--------------
>  1 files changed, 3 insertions(+), 14 deletions(-)
>
> diff --git a/arch/arm/mach-mx5/board-mx51_efikamx.c b/arch/arm/mach-mx5/board-mx51_efikamx.c
> index b7946f8..e237040 100644
> --- a/arch/arm/mach-mx5/board-mx51_efikamx.c
> +++ b/arch/arm/mach-mx5/board-mx51_efikamx.c
> @@ -121,23 +121,10 @@ static iomux_v3_cfg_t mx51efikamx_pads[] = {
>  };
>  
>  /* Serial ports */
> -#if defined(CONFIG_SERIAL_IMX) || defined(CONFIG_SERIAL_IMX_MODULE)
>  static const struct imxuart_platform_data uart_pdata = {
>  	.flags = IMXUART_HAVE_RTSCTS,
>  };
>  
> -static inline void mxc_init_imx_uart(void)
> -{
> -	imx51_add_imx_uart(0, &uart_pdata);
> -	imx51_add_imx_uart(1, &uart_pdata);
> -	imx51_add_imx_uart(2, &uart_pdata);
> -}
> -#else /* !SERIAL_IMX */
> -static inline void mxc_init_imx_uart(void)
> -{
> -}
> -#endif /* SERIAL_IMX */
> -
>  /* This function is board specific as the bit mask for the plldiv will also
>   * be different for other Freescale SoCs, thus a common bitmask is not
>   * possible and cannot get place in /plat-mxc/ehci.c.
> @@ -320,7 +307,9 @@ static void __init mxc_board_init(void)
>  					ARRAY_SIZE(mx51efikamx_pads));
>  	mx51_efikamx_board_id();
>  	mxc_register_device(&mxc_usbdr_host_device, &dr_utmi_config);
> -	mxc_init_imx_uart();
> +	imx51_add_imx_uart(0, &uart_pdata);
> +	imx51_add_imx_uart(1, &uart_pdata);
> +	imx51_add_imx_uart(2, &uart_pdata);

I'm even wondering if configuring uart 1 and 2 is necessary. afair only
ttymxc0 is really used

Arnaud

[PATCH 13/13] ARM i.MX51 efikamx: remove unnecessary CONFIG_SERIAL_IMX ifdefs

[Sascha Hauer]

On Thu, Jan 27, 2011 at 02:48:25PM +0100, Arnaud Patard wrote:
> Sascha Hauer <s.hauer@pengutronix.de> writes:
> 
> Hi,
> 
> > Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
> > ---
> >  arch/arm/mach-mx5/board-mx51_efikamx.c |   17 +++--------------
> >  1 files changed, 3 insertions(+), 14 deletions(-)
> >
> > diff --git a/arch/arm/mach-mx5/board-mx51_efikamx.c b/arch/arm/mach-mx5/board-mx51_efikamx.c
> > index b7946f8..e237040 100644
> > --- a/arch/arm/mach-mx5/board-mx51_efikamx.c
> > +++ b/arch/arm/mach-mx5/board-mx51_efikamx.c
> > @@ -121,23 +121,10 @@ static iomux_v3_cfg_t mx51efikamx_pads[] = {
> >  };
> >  
> >  /* Serial ports */
> > -#if defined(CONFIG_SERIAL_IMX) || defined(CONFIG_SERIAL_IMX_MODULE)
> >  static const struct imxuart_platform_data uart_pdata = {
> >  	.flags = IMXUART_HAVE_RTSCTS,
> >  };
> >  
> > -static inline void mxc_init_imx_uart(void)
> > -{
> > -	imx51_add_imx_uart(0, &uart_pdata);
> > -	imx51_add_imx_uart(1, &uart_pdata);
> > -	imx51_add_imx_uart(2, &uart_pdata);
> > -}
> > -#else /* !SERIAL_IMX */
> > -static inline void mxc_init_imx_uart(void)
> > -{
> > -}
> > -#endif /* SERIAL_IMX */
> > -
> >  /* This function is board specific as the bit mask for the plldiv will also
> >   * be different for other Freescale SoCs, thus a common bitmask is not
> >   * possible and cannot get place in /plat-mxc/ehci.c.
> > @@ -320,7 +307,9 @@ static void __init mxc_board_init(void)
> >  					ARRAY_SIZE(mx51efikamx_pads));
> >  	mx51_efikamx_board_id();
> >  	mxc_register_device(&mxc_usbdr_host_device, &dr_utmi_config);
> > -	mxc_init_imx_uart();
> > +	imx51_add_imx_uart(0, &uart_pdata);
> > +	imx51_add_imx_uart(1, &uart_pdata);
> > +	imx51_add_imx_uart(2, &uart_pdata);
> 
> I'm even wondering if configuring uart 1 and 2 is necessary. afair only
> ttymxc0 is really used

I can't say because I do not have the hardware. Anyway, this would be
subject to another patch.

Sascha

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |